Toshiba IK-TF9U instruction manual External Appearance Diagram, Before Making a Service Call

Page 33

10. EXTERNAL APPEARANCE DIAGRAM

1.73 [44]	0.21
1.73 [44]	[5.3]
1.73 [44]	[22]
	0.87
	0.18 [4.5]
	1.02 [26]

0.19 [4.8]

78 [3.07]	0.25
78 [3.07]	[6.3]
	34 [1.33]
0.19 [4.8]
2.20 [56]	4-M3 Depth 3
0.98 [25]	1.02 [26]
	4-M2 Depth 3

0.960.98

[24.5] [25]

Unit : inch [mm]

0.47 [12]

0.32 [8.2]

2-M2

0.76

[19.2]

* inch = mm/25.4

11. BEFORE MAKING A SERVICE CALL

Symptom	Items to be checked
No image	• Is the power supplied correctly?
	• Is the lens iris adjusted correctly?
	• Are the cables connected correctly?
	• Is the shutter mode set correctly?
	• Is the image process equipment set correctly?
Poor color	• Is the monitor adjusted correctly?
	• Is the white balance of the camera adjusted correctly?
	• Is the illumination dark?

Image 33

Contents Following information is only for EU-member states IK-TF9USafety Precautions Disclaimer Table of Contents Components Names and Functions Connector Pin Assignments ConnectionStandard Connection Operation Automatic Black BalanceWhite Balance Temp LOW Result displayed MeaningAvailable selections Items Controlled by Using on Screen DisplayUsing the Menus Mode Setting by on Screen DisplayShutter Electronic shutter MenusFlicker may be large TRGMode = Manual Changing each setting in Manu modePartial scanning setting Menu UP, DownChanging each setting in SS synchro. scan mode Mode = SSChanging the shutter speed setting Changing each setting in 1P SNR mode Changing each setting in E.TRG modeChanging the polarity of inputting trigger pulse setting Changing 1P SNR exposure time settingMode = E.TRG E.TRG = 1P SR Changing each setting in 1P SR modeChanging 1P SR exposure time setting 1P SNR, 1P SR, PW SNR, PW SRMode = E.TRG E.TRG = PW SNR Changing each setting in PW SNR modeChanging each setting in PW SR mode Mode = E.TRG E.TRG = PW SRMode = E.TRG E.TRG = RR Changing each setting in Gain Changing the gain in Manu modeGain Video gain WHT BAL White balance Changing gamma correction MANU/OFFChanging master pedestal Changing R pedestalOption SyncSetting to factory setting status Setting by the frameSetting by 2H Synchro. Scan Operation1 Pulse Trigger SYNC-NON Reset Picture Output Timing 1P SNR 1 Pulse Trigger Sync Non ResetE. TRG External trigger Fval Lval Dval1 Pulse Trigger SYNC-RESET Picture Output Timing 1P SR 1 Pulse Trigger Sync ResetPulse Width Trigger SYNC-NON Reset Picture Output Timing PW SNR Pulse width trigger SYNC-NON Reset1 Pulse Width Trigger SYNC-RESET Picture Output Timing PW SR Pulse width trigger SYNC-RESETRR Reset restart Input Timing Chart ExampleLong Term Exposure Partial Read When Partial Scanning Mode is onPartial Scanning OFF All pixels scanning Partial Scanning onUsing the unit with external sync signal External sync signal polarityExternal Sync External sync frequency rangeHorizontal Output Waveform Timing Chart Output Waveform Timing ChartVertical Output Waveform Timing Chart Fval LVAL、 DvalRGB, 3CCD SpecificationsExternal Appearance Diagram Before Making a Service CallSymptom Items to be checked One 1 Year Limited Warranty of Labor and Parts Limited Warranty Toshiba CCD CameraHow to Obtain Warranty Service Step-By-Step Procedures Your Responsibilities