Toshiba IK-TF9U Synchro. Scan Operation, Setting by the frame, Setting to factory setting status

Page 23

( 7 ) Setting to factory setting status

All the settings can be returned to the factory default status (preset status).

(1)If characters are displayed on the screen, press the [DISP] button to disable the character display.

(2)Push [MENU DOWN] and [DATA DOWN] buttons simultaneously for approx. 1 second.

(3)The preset operation starts. When the preset operation finishes, the character PRESET OK is displayed for approx. 1 second.

7. 3 Synchro. Scan Operation

The shutter speed can be set by the double horizontal scanning period (2H) or by the frame.

( 1 ) Setting by 2H

2H/1592H ~ 1590H/1592H stands for the setting by the 2H and the shutter speed can be set by the 2H (62.8 s).

When operating Partial Scannig, the number’s listed below can be used for setting.

25fps, E25fps

2H/1270H ~ 1268H/1270H

30fps, E30fps

2H/1060H ~ 1058H/1060H

35fps, E35fps

2H/910H ~ 908H/910H

40fps, E40fps

2H/774H ~ 772H/774H

45fps, E45fps

2H/706H ~ 704H/706H

50fps, E50fps

2H/636H ~ 634H/636H

( 2 ) Setting by the frame

2FRM to 512FRM stand for the setting (long period exposure) by the frame.

The video signal stored during the frame period set is output as 1 frame video image at a frame interval specified.

(Internal VD)

RGB data (video interval image)

FVAL

LVAL,

DAVL

n

n+1

(4FRM setting)

23

Image 23
Contents Following information is only for EU-member states IK-TF9USafety Precautions Disclaimer Table of Contents Components Names and Functions Standard Connection Connector Pin AssignmentsConnection White Balance OperationAutomatic Black Balance Temp LOW Result displayed MeaningAvailable selections Items Controlled by Using on Screen DisplayUsing the Menus Mode Setting by on Screen DisplayTRG MenusShutter Electronic shutter Flicker may be largeMenu UP, Down Changing each setting in Manu modeMode = Manual Partial scanning settingChanging the shutter speed setting Changing each setting in SS synchro. scan modeMode = SS Changing 1P SNR exposure time setting Changing each setting in E.TRG modeChanging each setting in 1P SNR mode Changing the polarity of inputting trigger pulse setting1P SNR, 1P SR, PW SNR, PW SR Changing each setting in 1P SR modeMode = E.TRG E.TRG = 1P SR Changing 1P SR exposure time settingMode = E.TRG E.TRG = PW SNR Changing each setting in PW SNR modeMode = E.TRG E.TRG = RR Changing each setting in PW SR modeMode = E.TRG E.TRG = PW SR Gain Video gain Changing each setting in GainChanging the gain in Manu mode WHT BAL White balance Changing R pedestal MANU/OFFChanging gamma correction Changing master pedestalOption SyncSynchro. Scan Operation Setting by the frameSetting to factory setting status Setting by 2HFval Lval Dval 1P SNR 1 Pulse Trigger Sync Non Reset1 Pulse Trigger SYNC-NON Reset Picture Output Timing E. TRG External trigger1 Pulse Trigger SYNC-RESET Picture Output Timing 1P SR 1 Pulse Trigger Sync ResetPulse Width Trigger SYNC-NON Reset Picture Output Timing PW SNR Pulse width trigger SYNC-NON Reset1 Pulse Width Trigger SYNC-RESET Picture Output Timing PW SR Pulse width trigger SYNC-RESETLong Term Exposure RR Reset restartInput Timing Chart Example Partial Scanning on When Partial Scanning Mode is onPartial Read Partial Scanning OFF All pixels scanningExternal sync frequency range External sync signal polarityUsing the unit with external sync signal External SyncFval LVAL、 Dval Output Waveform Timing ChartHorizontal Output Waveform Timing Chart Vertical Output Waveform Timing ChartRGB, 3CCD SpecificationsSymptom Items to be checked External Appearance DiagramBefore Making a Service Call Your Responsibilities Limited Warranty Toshiba CCD CameraOne 1 Year Limited Warranty of Labor and Parts How to Obtain Warranty Service Step-By-Step Procedures