Toshiba IK-TF9U instruction manual PW SR Pulse width trigger SYNC-RESET

Page 27

( 4 ) PW SR (Pulse width trigger SYNC-RESET)

The trigger input to the CC1 of the DIGITAL terminal develops 1 frame images.

(4. 1) 1 Pulse Width Trigger SYNC-RESET Picture Output Timing

Negative polarity mode

Trigger*1

Positive polarity mode

About 1 ∝s	About 7 ∝s
	Exposure period*2
Exposure completion
	0 to 2H

(Internal VD)*3

RGB data (video interval image)

FVAL

LVAL,

DVAL

58H (Partial scanning OFF)

40H (Partial scanning 25fps)

56H (Partial scanning 30fps)

66H (Partial scanning 35fps)

78H (Partial scanning 40fps)

80H (Partial scanning 45fps)

86H (Partial scanning 50fps)

*1: Externally input signal

*2: Exposure time = Trigger pulse width + 6 ∝s

(Valid trigger pulse width is 2 ∝s or greater for external trigger shutter operation.)

*3: VD is generated after 0 to 2H following the completion of the exposure period and the video is synchro- nized to this and output.

Note:

When the next trigger is input before completion of the output of the video corresponding to the trig- ger, there will be an effect on the video.

27

Image 27

Contents Following information is only for EU-member states IK-TF9USafety Precautions Disclaimer Table of Contents Components Names and Functions Connector Pin Assignments ConnectionStandard Connection Operation Automatic Black BalanceWhite Balance Temp LOW Result displayed MeaningAvailable selections Items Controlled by Using on Screen DisplayUsing the Menus Mode Setting by on Screen DisplayTRG MenusShutter Electronic shutter Flicker may be largeMenu UP, Down Changing each setting in Manu modeMode = Manual Partial scanning settingChanging each setting in SS synchro. scan mode Mode = SSChanging the shutter speed setting Changing 1P SNR exposure time setting Changing each setting in E.TRG modeChanging each setting in 1P SNR mode Changing the polarity of inputting trigger pulse setting1P SNR, 1P SR, PW SNR, PW SR Changing each setting in 1P SR modeMode = E.TRG E.TRG = 1P SR Changing 1P SR exposure time settingMode = E.TRG E.TRG = PW SNR Changing each setting in PW SNR modeChanging each setting in PW SR mode Mode = E.TRG E.TRG = PW SRMode = E.TRG E.TRG = RR Changing each setting in Gain Changing the gain in Manu modeGain Video gain WHT BAL White balance Changing R pedestal MANU/OFFChanging gamma correction Changing master pedestalOption SyncSynchro. Scan Operation Setting by the frameSetting to factory setting status Setting by 2HFval Lval Dval 1P SNR 1 Pulse Trigger Sync Non Reset1 Pulse Trigger SYNC-NON Reset Picture Output Timing E. TRG External trigger1 Pulse Trigger SYNC-RESET Picture Output Timing 1P SR 1 Pulse Trigger Sync ResetPulse Width Trigger SYNC-NON Reset Picture Output Timing PW SNR Pulse width trigger SYNC-NON Reset1 Pulse Width Trigger SYNC-RESET Picture Output Timing PW SR Pulse width trigger SYNC-RESETRR Reset restart Input Timing Chart ExampleLong Term Exposure Partial Scanning on When Partial Scanning Mode is onPartial Read Partial Scanning OFF All pixels scanningExternal sync frequency range External sync signal polarityUsing the unit with external sync signal External SyncFval LVAL、 Dval Output Waveform Timing ChartHorizontal Output Waveform Timing Chart Vertical Output Waveform Timing ChartRGB, 3CCD SpecificationsExternal Appearance Diagram Before Making a Service CallSymptom Items to be checked Your Responsibilities Limited Warranty Toshiba CCD CameraOne 1 Year Limited Warranty of Labor and Parts How to Obtain Warranty Service Step-By-Step Procedures