Millennium Enterprises Integrated Modeling Amplifier manual Power Amp Section, Audio Outputs

Page 95

Johnson Millennium

Section - 7 Appendix

Millennium Specifications

Power Amp Section:

80 Watts RMS per channel @ 8 ohms

125 Watts RMS per channel @ 4 ohms

Audio Outputs:

Left Speaker outputs: 2-1/4 inch jacks paralleled

Right Speaker outputs: 2-1/4 inch jacks paralleled

Loop Send: 1/4 inch TRS balanced / unbalanced: -10dBu Left/Right Direct/Recording

Outputs: 2- XLR servo-balanced: +4 dBu:

1 ground Maximum level: +18 dBu

Impedance: 100 ohms

Audio Inputs:

Bright Input: 1/4 inch unbalanced: sensitivity adjustable by input level control Impedance: 1 megohm

Normal Input: 1/4 inch unbalanced sensitivity adjustable by input level control Impedance: 1 megohm

Loop Return: 1/4 inch unbalanced: +18 dBu

Maximum Level: +18 dBu

Impedance: 10 kΩ

Controller Connections:

MIDI: In, Out/Thru

Expression Pedal inputs: 2- 1/4 inch;

compatible with any standard volume pedal with 25K to 1M Ω or voltage control pedal (0-5v).

J-3 footswitch input: 1/4inch TRS

J-12 Controller Input: 5 pin DIN female

Tube Complement:

2- 12Ax7 triodes: 300 volt power supply

DSP Section:

A/D Converter: 20 bit 128X oversampled delta sigma stereo

D/A Converter: 20 bit 128X oversampled

Sampling frequency: 44.1 kHz

Static Dynamic Instruction Set Computer (S-DISC II) Digital signal path width: 24 bits

Internal Data path width: 24 bits

Delay DRAM: 256 K x 24 (5.9 sec.)

Delay SRAM: 256 24 bit registers

Data ALU processing: 11.3 MIPS

Multiplier size: 24 x 24 bits

DSP co-processor

Digital Signal Path width: 24 bits

Internal Data Path width: 48 bits

Delay SRAM: 768 - 24 bit registers

Data ALU processing: 22.6 MIPS

Multiplier size: 24 X 24 bits

Power Requirements:

100, 120, 230 and 240 VAC 50/60 Hz 550 W Fuse: 100, 120 VAC 1/4” X 1 1/4” 6A

230, 240 VAC 5mm X 20mm 3.15A

Memory Capacity:

Factory: 100 Presets

User: 100 Presets

Dimensions: 28” (711mm) W x 11” (265mm) H x 12” (305mm) D

Net Weight: 42 lbs

Shipping Weight: 47 lbs

User Guide

87

Page 94 Page 96
Image 95
Page 94 Page 96
Contents User’s Guide Mains Plug Warning Product Name Manufacturer’s Name8760 S. Sandy Parkway Sandy, Utah 84070, USAQuick Start Table of Contents Digital Effects Section Editing Modules Advanced TopicsAmplifier Section Midi FunctionsAppendix Using the Johnson Amplification J-12 Foot ControllerUser Guide Congratulations IntroductionUser Guide Front Panel Quick Tour of the Millennium Two-Fifty100 User Guide F FX Library Buttons Loop Send Jack This is the effects loop send jack Rear PanelFuse- 100, 120 VAC 6 Amp fuse is inserted here American Stack Dual Rectifier, Boogie MK II, Soldano SLO Amplifier Model TypesEffects include Programmable Mono FX Loop Basic SpecificationsJohnson Amplification J-12 foot controller Foot Controller CompatibilityModule Sizes Module TypesMaking Connections Setting UpXLR Cabinet Emulation functions To exit this mode, simply press the Preset buttonAssign Mode Preset ModeFX Edit Mode Utility ModeGetting Sounds Input and Master Output AdjustmentsGain Adjustments EQ and Preset LevelAmplifier Contour Control Wet/Dry Mix Adjustments Global or LocalAmplifier Model and Channel Selection Digital FX Quick Adjust Knobs Press the Utility button once. The display reads Selecting a PresetUsing the Tuner Utility Menu Tuner ModeReference and Output Johnson Amplification J-12 Tuner ModeInstant Tuner Access Press the any button to exit the Tuner modeNaming the Preset Naming and Storing PresetsAfter which you are taken to the preset you have just stored Storing the PresetIntegrated Amplifier Model Selection Editing a PresetPreset Editing Sections Integrated Amplifier Model EditingBgain LVL Adig LVL Analog Wah EditingAvail Link for Pedal 1 OFF Noise Gate EditingTo exit Noise gate edit mode, press the Preset button Selecting Effect Configuration RoutesChanging Effect Modules Selecting a DefaultAdjusting the Module’s Parameters Custom DefaultsComparing Original Pst Comparing ChangesNaming the Default Storing/Naming DefaultsEditing a Module Storing the DefaultOutput Module Functions Scrolling through a Module’s PagesEffect Name Digital Effect Module Size and TypeChoruses Default ListAnalog Wah Parameters Effects LibraryAnalog Wah Amplifier TypesNoise Gate Parameters Noise GateStereo Reverb a true stereo version of the Reverb Module Digital EffectsReverbs ReverbReverb Parameters Gated ReverbTime Over TypeOver Freq Low PassChoruses and Flangers Chorus T C HChorus Parameters Flanger Parameters FlangerPhaser Parameters PhasersOver Rotary Speaker SimulatorMode LevelTremolo & Auto Panner Parameters Tremolo and Auto-PannerTremolo Auto PannerPitch Shifters Parameters Pitch Shifters and HarmonyDetuners Dtn E -H DelaysDetuner Parameters Smear Delay ParametersDly Time TapItCompressor Parameters CompressorGraphic Equalizer Parameters EqualizersGraphic Equalizers Parametric Equalizer Parameters Multi Effects Modules Chorus/Delay and Flange/DelayParametric Equalizers Multi-Effect Module Parameters Whammy EffectsAuto Wah Effect Parameters Auto WahWhammy Effect Parameters LFOs Assigning ModifiersMidi CCs Dynamic ModifiersLinking a Parameter to a Modifier External Expression PedalsSetting up a Dynamic Modifier Setting up an LFOAmplifier Morphing Morphing Pedal AssignmentsMorphing Between Effect Modules Volume Pedal AssignmentsVol Pdl Morph Pdl Midi Merging Setting the Midi ChannelsPreset Receive Map Midi FunctionsSysEx Device Channel Preset Transmit MapSysex Dumps After which it returns to the Preset dump screenSysEx Dump Bulk System After which it returns to the User default screenGlobal vs. Local XLR Cabinet Emulation Factory ResetOther Utility Functions Footswitch Set-Up Output Mode and Speaker Cabinet Voicing SelectionsExpression Pedal Names Configuring the PedalboardConnecting the Johnson Amplification J-12 Foot Controller Assigning Functions Assigning Presets to FootswitchesPress the Preset button to exit Gain Exp 1 Min 56Max Assigning Parameters to Footswitches/ Expression PedalsJ12FCBank FS=Tog CCTran Other Footswitch FunctionsAssigning Midi Control to the Expression Pedals 12 will appear like this When connected. The display now readsTurn Page knob to page 3 and the display will read Momentary Footswitch AssignmentNaming Banks Bank Up/ Tuner and Bank Down / Bypass FootswitchesUsing the Tuner Other Pedalboard TidbitsWill now read Un-Linking or Viewing Parameter ControlMatchless Bank 1 TopBank 2 Fender Bank 4 VoxStudio Bank 12 Alternative Bank 18 DynamicsBank 13 Country Bank 19 Morph Bank 14 VintageBank 3 Boogie/Soldano Millennium Preset DescriptionsBank 6 Marshall Bank 5 MatchlessBank 8 Signature Bank 13 Country Bank 12 AlternativeBank 16 Jazz/Fusion Bank 15 StudioBank 18 Dynamics ConfigStereo 2,2 ConfigParall 4,4,2 ConfigMonoSplit 4,4,4,4 Effect Configuration ChartHarmony Interval Charts Audio Inputs Power Amp SectionPower Requirements Audio OutputsRemarks Midi Implementation ChartJohnson Amplification System Exclusive ImplementationMidi Basics General Format ProceduresSYSHEAD, 11h, F7h SYSHEAD, 49h, F7hSyshead 48h, dd1st1 dd1st2, ... ddnth1, ddnth2, F7h Ddn Bbs Vv = Software version number Rr =Tt = Syshead 17h, aa1, aa2,bbs1, bbs2, F7hNumber of available parameters in the FX Module Number of ModulesModules User requested Indicates the beginning of the xth ModuleSYSHEAD, 54h, cc, F7h 02h Effect Module 03h 04h Whole Effect ModuleYy= effect ID # SYSHEAD, 21h, F7hSYSHEAD, 22h, F7h SYSHEAD, 13h, yy1, yy2, zz1, zz2 F7hKey Label Hex equivalent SysEx Button/Keys/Footswitch codesFX Module Count for Module Types 00 FX Module Class Type SysEx Preset Dump ExampleFx Module codes and numbers PEQ 100 101 102 103 104 105 106 107
Top Page Image Contents