Millennium Enterprises Integrated Modeling Amplifier manual General Format, Procedures

Page 98

Section - 7 Appendix

Johnson Millennium

Pitch Bend: Pitch Bend information is a higher resolution controller that is not supported in Johnson Amplification products, due to the density of the information and the resources needed to process it properly. Many MIDI control products offer the ability to map Pitch Bend to normal Continuous Controllers if a user wanted to control a parameter with a device such as a Pitch Bend Wheel.

General Format

The general format for the System Exclusive information is as follows (note: all SysEx values are displayed in Hexadecimal format, along with this symbol (h) for clarification):

Hex Value	Definition
F0(h)	System Exclusive ‘Begin Message’ byte
00(h)
00(h)	Manufacturer’s ID Number (Johnson Amplification)
10(h)
0n(h)	n = Unit’s Device or SysEx Channel number (minus one)
	e.g.	00(h)	is device or SysEx Ch 1
		01(h)	is device or SysEx Ch 2 etc...
		0F(h)	is device or SysEx Ch 16

dd	dd = device ID number	4A(h)	identifies the Millennium
pp	pp = Procedure number. The different procedure’s names and general formats are
		described in the Procedures Section.
dd(1)1, dd(1)2	dd(n)1, dd(n)2
	dd = Data as needed by procedures. Since the standard MMA MIDI Specification reserves 80(h)
	through FF(h) (decimal numbers 128 through 255) for specific commands, a split byte format is
	adopted for all data communication in this SysEx implementation. dd(n)2 denotes the 1st
	through 7th bits of the nth byte and dd(n)1 denotes th 8th bit of the nth byte. Note: All data that
	is requested or received, is in split byte format unless noted otherwise.
F7(h)	System Exclusive ‘End Message’ byte

Procedures

In the following section, SYS_HEAD refers to a valid System Exclusive header. The System Exclusive header starts with the System Exclusive status byte, and includes all bytes through the Johnson Amplification device type. F7(h) is the System Exclusive ‘Message End’ byte. All SysEx numbers in the format definition of each procedure are given as hexadecimal values, along with this symbol (h) for clarification. Binary numbers are identified with this symbol (b).

90

User Guide

Image 98

Contents User’s Guide Mains Plug Warning Sandy, Utah 84070, USA Manufacturer’s Name8760 S. Sandy Parkway Product NameQuick Start Table of Contents Midi Functions Editing Modules Advanced TopicsAmplifier Section Digital Effects SectionUsing the Johnson Amplification J-12 Foot Controller AppendixUser Guide Introduction CongratulationsUser Guide Quick Tour of the Millennium Two-Fifty Front Panel100 User Guide F FX Library Buttons Loop Send Jack This is the effects loop send jack Rear PanelFuse- 100, 120 VAC 6 Amp fuse is inserted here Amplifier Model Types American Stack Dual Rectifier, Boogie MK II, Soldano SLOEffects include Basic Specifications Programmable Mono FX LoopFoot Controller Compatibility Johnson Amplification J-12 foot controllerModule Types Module SizesSetting Up Making ConnectionsTo exit this mode, simply press the Preset button XLR Cabinet Emulation functionsUtility Mode Preset ModeFX Edit Mode Assign ModeEQ and Preset Level Input and Master Output AdjustmentsGain Adjustments Getting SoundsAmplifier Contour Control Wet/Dry Mix Adjustments Global or LocalAmplifier Model and Channel Selection Digital FX Quick Adjust Knobs Utility Menu Tuner Mode Selecting a PresetUsing the Tuner Press the Utility button once. The display readsPress the any button to exit the Tuner mode Johnson Amplification J-12 Tuner ModeInstant Tuner Access Reference and OutputNaming and Storing Presets Naming the PresetStoring the Preset After which you are taken to the preset you have just storedIntegrated Amplifier Model Editing Editing a PresetPreset Editing Sections Integrated Amplifier Model SelectionBgain LVL Analog Wah Editing Adig LVLNoise Gate Editing Avail Link for Pedal 1 OFFSelecting Effect Configuration Routes To exit Noise gate edit mode, press the Preset buttonCustom Defaults Selecting a DefaultAdjusting the Module’s Parameters Changing Effect ModulesComparing Changes Comparing Original PstStoring/Naming Defaults Naming the DefaultStoring the Default Editing a ModuleScrolling through a Module’s Pages Output Module FunctionsDigital Effect Module Size and Type Effect NameDefault List ChorusesAmplifier Types Effects LibraryAnalog Wah Analog Wah ParametersNoise Gate Noise Gate ParametersReverb Digital EffectsReverbs Stereo Reverb a true stereo version of the Reverb ModuleGated Reverb Reverb ParametersLow Pass Over TypeOver Freq TimeChoruses and Flangers T C H ChorusChorus Parameters Flanger Flanger ParametersPhasers Phaser ParametersLevel Rotary Speaker SimulatorMode OverAuto Panner Tremolo and Auto-PannerTremolo Tremolo & Auto Panner ParametersPitch Shifters and Harmony Pitch Shifters ParametersDetuners Dtn E -H DelaysDetuner Parameters TapIt Delay ParametersDly Time SmearCompressor Compressor ParametersGraphic Equalizer Parameters EqualizersGraphic Equalizers Parametric Equalizer Parameters Multi Effects Modules Chorus/Delay and Flange/DelayParametric Equalizers Whammy Effects Multi-Effect Module ParametersAuto Wah Effect Parameters Auto WahWhammy Effect Parameters Dynamic Modifiers Assigning ModifiersMidi CCs LFOsExternal Expression Pedals Linking a Parameter to a ModifierSetting up an LFO Setting up a Dynamic ModifierMorphing Pedal Assignments Amplifier MorphingVolume Pedal Assignments Morphing Between Effect ModulesVol Pdl Morph Pdl Midi Functions Setting the Midi ChannelsPreset Receive Map Midi MergingPreset Transmit Map SysEx Device ChannelAfter which it returns to the Preset dump screen Sysex DumpsAfter which it returns to the User default screen SysEx Dump Bulk SystemGlobal vs. Local XLR Cabinet Emulation Factory ResetOther Utility Functions Output Mode and Speaker Cabinet Voicing Selections Footswitch Set-UpExpression Pedal Names Configuring the PedalboardConnecting the Johnson Amplification J-12 Foot Controller Assigning Functions Assigning Presets to FootswitchesPress the Preset button to exit Assigning Parameters to Footswitches/ Expression Pedals Gain Exp 1 Min 56MaxOther Footswitch Functions J12FCBank FS=Tog CCTranAssigning Midi Control to the Expression Pedals When connected. The display now reads 12 will appear like thisMomentary Footswitch Assignment Turn Page knob to page 3 and the display will readOther Pedalboard Tidbits Bank Up/ Tuner and Bank Down / Bypass FootswitchesUsing the Tuner Naming BanksUn-Linking or Viewing Parameter Control Will now readBank 4 Vox Bank 1 TopBank 2 Fender MatchlessBank 14 Vintage Bank 12 Alternative Bank 18 DynamicsBank 13 Country Bank 19 Morph StudioMillennium Preset Descriptions Bank 3 Boogie/SoldanoBank 5 Matchless Bank 6 MarshallBank 8 Signature Bank 12 Alternative Bank 13 CountryBank 15 Studio Bank 16 Jazz/FusionBank 18 Dynamics Effect Configuration Chart ConfigStereo 2,2 ConfigParall 4,4,2 ConfigMonoSplit 4,4,4,4Harmony Interval Charts Audio Outputs Power Amp SectionPower Requirements Audio InputsMidi Implementation Chart RemarksJohnson Amplification System Exclusive ImplementationMidi Basics Procedures General FormatSYSHEAD, 11h, F7h SYSHEAD, 49h, F7hSyshead 48h, dd1st1 dd1st2, ... ddnth1, ddnth2, F7h Ddn Syshead 17h, aa1, aa2,bbs1, bbs2, F7h Vv = Software version number Rr =Tt = BbsIndicates the beginning of the xth Module Number of ModulesModules User requested Number of available parameters in the FX Module02h Effect Module 03h 04h Whole Effect Module SYSHEAD, 54h, cc, F7hSYSHEAD, 13h, yy1, yy2, zz1, zz2 F7h SYSHEAD, 21h, F7hSYSHEAD, 22h, F7h Yy= effect ID #SysEx Button/Keys/Footswitch codes Key Label Hex equivalentSysEx Preset Dump Example FX Module Count for Module Types 00 FX Module Class TypeFx Module codes and numbers PEQ 100 101 102 103 104 105 106 107