JVC GY-DV5001 manual Power Supply, AC Operation, Battery Pack Operation Optional, Camera

Page 33

4. POWER SUPPLY

The GY-DV5000 is operable with AC power supply or battery pack.

4-1 AC Operation

Use the JVC AA-P250 AC power adapter (max. rated output 12.5 V DC, 3.5 A) as the AC power supply.

AA-P250

DC cable

AC power adaptor

PHONES

DV

REAR AUDIO IN

TALLY

DC IN

DC OUT

Do not use any power source with large fluctuations in the power source voltage, power sources generating noise, such as ripples or power sources with lower voltage.

1. After making sure that the power switches of the GY-DV5000 and of the AA-P250 are set to OFF, connect the DC cable from the AA-P250 to the DC IN connector of the GY-DV5000 as shown in the illustration.

2. Set the CHARGE/CAMERA switch of the AA-P250 to

CAMERA.

3. Press the POWER switch of the GY-DV5000 to ON. Power is supplied to the VTR section and the camera.

* For details, read the instruction manual of the AA-P250.

MEMO:

Do not remove or connect the DC cable while recording is being performed.

4-2 Battery Pack Operation (Optional)

The GY-DV5000 can be operated with the following battery packs.

■Flat shape type battery pack

■Anton-Bauer battery pack

● Propack 13/14 Series

● Trimpack 13/14 Series

● Magnum 13/14 Series

● Compack 13/14 Series

 

*An Anton-Bauer battery pack cannot be connected directly to the GY-DV5000. It is necessary to mount the optional battery holder.

Battery holder: Anton-Bauer QRQ27

For details on how to mount the battery holder, see page 35.

●When the DC cable is connected to the DC IN connector, the power supply from the battery pack is interrupted and the power starts to be supplied through the DC IN connector.

●Do not connect or disconnect the DC cable while operating with a battery pack.

The following symptoms may occur if the DC cable is connected or disconnected while operating with a battery pack.

•The power is cut off for a moment when the DC cable is disconnected.

•Noise to the video and audio signals occurs. Audio signal are muted.

●When operation is continued with DC input after the battery pack capacity has been used up, set the POWER switch to OFF after the DC power is applied. Then switch ON again.

●If the GY-DV5000 is left with the battery pack attached, a small amount of power is consumed even if the POWER switch on the GY-DV5000 is set to OFF. Remove the battery pack when the GY-DV5000 is not going to be used.

E-33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents LWT0074-001C-H GY-DV5001MANUEL D’INSTRUCTIONS Instrucciones IstruzioniDV signal input is possible with the GY-DV5001E Port Cable LengthThese instructions are for the GY-DV5000E and GY-DV5001E Rating plate serial number plate is on the top frame Main Features Connecting a Video Component with DV Connector Main FeaturesAC Operation Battery Pack Operation Optional 11-11Introduction Precautions for Proper UsePrecautions for Use of Head Cleaning Tape Routine and Periodical MaintenanceHead cleaner Tape guides & rollers Time managementUse JVC’s videocassette tapes marked with the or Symbol Battery Pack to be UsedVideocassette to be Used For recording and storing videotapes in the best conditionCondensation Characteristic CCD PhenomenaSmear and Blooming Moire or AliasingFront Section CONTROLS, Indicators and ConnectorsFilter Colour temperature conversion filter control knob Auto WHITE/ACCU Focus switchLens mounting ring/Lens lock lever White BalanceRight Side Section CAM Camera mode indicator Black Black stretch/black compression switchVTR VTR mode indicator Power Power ON/OFF switchRight Side Section Cont’d @ Monitor Select Audio monitor selector switch CH-1/CH-2 Audio Input CH-1/CH-2 audio input selector switch# Counter Counter display switch $ TC GENE. Time code generator setting switchCH1/CH2 Line OUT CH1/CH2 line output connector RCA Monitor OUT Monitor output connector BNCC OUT Y/C output connector 4-pin Left Side SectionTop Section Rear Section Battery holder DV connectorBattery holder lock release knob Breaker Breaker buttonVTR mode Example of display Camera mode Example of displayIndications on the LCD Monitor and in the Viewfinder Status ScreensStatus Screens in the Camera Mode Indications on the LCD Monitor and in the Viewfinder Cont’d Status Screen in VTR Mode Magnified Status Indications on the LCD Monitor Head Cleaning Required Cleaning TapeNtsc Inhibit REC InhibitSafety Zone Indication Camera mode only Auto White Balance Indication Camera mode onlyMenu Setting Screen TOP Menu screen Camera modeS14 x 7.3B12U Zoom Lens OptionalVF-P115B 1.5-Inch Viewfinder OptionalBasic System Basic System Connections and AdjustmentsAttaching the Viewfinder Attaching the Zoom LensPin Hole ViewfinderAttaching the Microphone Using KA-A50U Attaching the Microphone ProvidedAttaching the Microphone Optional Attaching the Tripod Base Provided Front mount clip Safety lever Lock leverTripod mounting holes Front base mountBattery Pack Operation Optional Power SupplyFlat shape type battery pack Anton-Bauer battery pack AC OperationUsing a Flat Shape Type Battery Pack optional Battery Pack Operation Optional Cont’dUsing an Anton-Bauer Battery Pack Attaching the Battery PackDetaching the Battery Pack Battery Pack Continuous Operating Time at 25 ˚C Operating Time with Battery PackRecharging SonyTurning the Power OFF Turning the Power onMode Operation PreparationsLoading the Cassette Cassette Loading and UnloadingREC Save VTRUnloading the Cassette Open knobCassette cover Eject button Viewing the LCD Monitor Adjusting the LCD monitorOpening the LCD monitor Changing the orientation and angle of the LCD monitorSetting the Date and Time Setting, Displaying and Recording the Date and TimeDial MenuClock Adjust menu screen Date Year/Month/Day Setting, Displaying and Recording the Date and Time Cont’dRecording the Date and Time Data Displaying the Time and Date on the ScreenCharging the Built-in Battery How to chargeAC outlet AA-P250 DC cable Screen Size 43/LETTER Mode Selection Camera SettingsFilter Suitable LocationExternal Monitor Adjustment Viewfinder AdjustmentAdjust the position and angle of the viewfinder Colour video monitorAccu Focus can also be used in the above step Back Focus AdjustmentWhite Balance Adjustment Audio Input Signal Selection LineMIC Recording Level Adjustment Auto mode is selected in the Full Auto shooting modeUsing the audio input level control on the front section Monitoring Audio during Recording Monitor Select switchBasic Recording Operation Shooting OperationWhen the power should be turned off When it is required to unload the videocassetteAbout the Quick REC Start Mode Tally lampEdit Search Searching for Recorded Scenes Edit SearchScreen indications during Edit Search Searching the tape in forward directionSetting the time before the tape protection mode is Engaged If the Record-Standby Mode ContinuesHeader REC menu screen contents Header REC FunctionDescription How to set the Header REC menu screen Executing the Header REC FunctionDuring Header REC Output switch Colour bar signal of the built-in signal generatorRecording the Colour Bars Playback Procedure Playback ModePower switch Mode switch Display of time codeFast-Forward, Rewind SearchBlank Search VTR indicator SettingOutputting CH-3, CH-4 Channel Audio Shutter dial Status button TOP Menu screenUsing External Components Connecting a Video Component with DV ConnectorDV connector DV cable VC-VDV204 4P-4P, VC-VDV206 4P- 6P Operation Connections SettingsDate and time data Data transmitted from the playback unit is recordedTC GENE. switch Presetting and Recording of Time CodeTime Code Operation Displaying Time CodeTime code hour, min, sec, frame Zero-resetting the Time Code or User’s Bit DataTC Gene switch Set the TC Gene switch inside the cover on the side toReproducing Time Codes RegenMenu Screens 11-1Menu Screen ConfigurationStatus button 11-2Setting Menu ScreensShutter STA Termenu dial Cursor Menu screenReading Out a Menu Settings File Storing Setting ValuesResetting the Menu Settings to the Factory Settings 11-3FILE Manage Menu Screen11-4TOP Menu Screen 11-5CAMERA Operation Menu Screen 11-6CAMERA Process Menu Screen 11-7ADVANCED Process Screen 11-8SKIN Color Adjust Screen11-9AUDIO Menu Screen 11-10 LCD/VF Menu Screen 11-10 LCD/VF Menu Screen Cont’d 11-11 TC/UB/CLOCK Menu Screen Header REC Menu Screen TIME/DATE Menu Screen Others Menu Screen Battery Alarm VRType FrontSetting procedure Features of the Camera SectionWHT.BAL switch Full-Time Auto White Balance FAWAutomatic adjustment Iris Brightness AdjustmentManual adjustment Temporary auto iris adjustmentOperation Adjusting the Shutter SpeedShutter STA TER Set the Shutter item on the Camera Operation menu screen Variable Scan V.SCAN Shooting the Screen Image on a Computer MonitorBand Video monitor Basic operationGain switch Gain Sensitivity AdjustmentSwitch Position Factory-Set Gain Relationship between gain, iris and shutterAutomatic Setting Contents Switch Setup According to Illumination and SubjectSetting the Color and Range of the Skin Detail Function How to Use Skin DetailDetection AreaUsing the Skin Detail Function StatusDisplay Others Alarm Indications and ActionsScreen indications on the LCD monitor and in the Viewfinder Indication Condition RemedyError Code Error Details GY-DV5000 Operation Remedy Blinking Pattern Remaining Battery/TapeTally lamp Camera to operate REC/ALARM lamp Battery lamp Alarm Indications and Actions Cont’dAlarm Sound Viewfinder Warning LampsSymptoms Remedy TroubleshootingTape. See Precautions for Use of Head Cleaning Tape on TypeShutter dial Status button Hour Meter DisplayOthers 2/2 menu screen Accumulated drum running timeSpecifications External Dimensions unit mm Specifications Cont’dViewfinder VF-P115B, VF-P116 Power zoom lens YH16 ⋅ 7K12U, YH19 ⋅ 6.7K12U CanonGY-DV5000/GY-DV5001 DV Camcorder
Top Page Image Contents