JVC GY-DV5001 manual 11-9AUDIO Menu Screen

11. MENU SCREENS

11-9AUDIO Menu Screen

Item		Function	Variation Range	Initial Setting
TEST TONE	Sets whether or not the audio reference signal (1kHz, –20dBFS or		OFF	OFF
	–12dBFS) should be output while the colour bar is output.		ON
	OFF: Audio reference signal is not output.
	ON: Audio reference signal is output.
AUDIO MODE	Selects the sampling frequency for audio recording (both CH-1 and CH-		32K	48K
	2)		48K
	32K : Recording is performed with 12-bit, 32 kHz sampling frequency
	48K : Recording is performed with 16-bit, 48 kHz sampling frequency
	* The DV format offers recording tracks for up to 4 channel when using
	12-bit, 32 kHz sampling. The GY-DV5000 records two of these track.
	The GY-DV5000 does not allow after-recording.
A.OUT	Selects whether or not audio should be output during search.		OFF	ON
AT SEARCH	OFF : Audio is not output		ON
	ON : Audio is output
CH1 FRONT	Used to select whether or not the front section audio level control should		DISABLE	ENABLE
VR	be operative. The front section audio level control only affects the audio		ENABLE
	signal recorded on CH1.
	DISABLE: Use of the front section audio level control is disabled.
	ENABLE: Use of the front section audio level control is enabled.
	* The operation of the CH-1 audio level control on the side section is
	unaffected by this setting.
WIND CUT	To select whether or not the low frequencies of the audio signal from the		OFF	OFF
	audio input connectors are cut. Set to ON to reduce the wind noise of the		FRONT
	microphone.		REAR
	OFF	: Low frequencies are not cut.	BOTH
	FRONT : Only the low frequencies of the audio signal input to the FRONT
		AUDIO IN connector are cut.
	REAR	: Only the low frequencies of the audio signal input to the REAR
		AUDIO IN connector are cut.
	BOTH	: The low frequencies are cut for both the FRONT and REAR
		AUDIO IN connectors.
AUDIO REF.	Sets the reference audio level of the tape (both CH-1 and CH-2).		–20dB	–20dB
LEVEL	–20dB : Records with –20 dB as the reference audio level.		–12dB
	–12dB : Records with –12 dB as the reference audio level. Use this setting
		when playing back the tape using DV equipment for general
		consumer use.

*Use the same setting for playback as for recording.

*This setting is unrelated to the audio level of the DV signal. (GY-DV5001 only)

AUDIO	Used to select which channels to reproduce when playing back a tape				CH1/2	CH1/2
SELECT	with sound recorded on 4 channels. (Can only be set in the VTR mode.)				MIX
	CH1/2 : To reproduce the sound recorded on CH-1 and CH-2.				CH3/4
			The GY-DV5000 records audio on the CH-1 and CH-2 channels
			during shooting.
	MIX		: To simultaneously reproduce the sound of all four channels.
	CH3/4 : To reproduce the sound of the CH-3 and CH-4 channels.
		MEMO:
	The GY-DV5000 does not allow after-recording on the CH-3 and CH-
	4 channels.
AUDIO	Selects whether stereo sound or mixed sound is output from the PHONES				STEREO	MIX
MONITOR	jack when the MONITOR SELECT switch is set to MIX.				MIX
	STEREO : Stereo sound (CH-1 audio is output from L, CH-2 audio is
				output from R)
	* Only audio of CH-1 is output from the monitoring loudspeaker.
	MIX		: Mixed sound (The mixed CH-1 and CH-2 audio is output
				from L and R)
PAGE BACK	The TOP MENU screen returns when the SHUTTER dial is pressed while				–––––	–––––
	the cursor is at this position.

E-74