JVC LYT1325-001A manual Audio Dubbing, Insert Editing, Editing EN

EDITING EN 43

Audio Dubbing

The audio track can be customised only when recorded in the 12-BIT and SP modes. (
pg. 29)

●Use the provided remote control or an optional remote control kit RM-V717KITU.

	Headphone Connector		Microphone
			Connector
	Speaker
	START/
	STOP
	PAUSE	Stereo Microphone
REW	PLAY
INSERT	STOP
	A.DUB

1 Play back the tape to locate the point where editing will start, then press PAUSE (9).

2 While holding A. DUB (D) on the remote control, press PAUSE (9). The “9D” and “MIC” indicators appear.

3 Press PLAY (U), then begin “narrating”. Speak into the microphone.

●To pause dubbing, press PAUSE (9).

4 To end Audio Dubbing, press PAUSE (9), then STOP (8).

To hear the sound during Audio Dubbing

Connect optional headphones to the headphone connector or use the AV connector, and set the “NARRATION” to the desired mode;

●“OFF” for the playback sound.

●“ON” for the dubbed sound.

●“MIX” for the playback and dubbed sound.

To hear the dubbed sound during playback

Set “NARRATION” to “ON” or “MIX”. (
pg. 29, 32)

NOTES:

●When editing onto a tape that was recorded at 12-BIT, the old and new soundtracks are recorded separately.

●If you dub onto a blank space on the tape, the sound may be disrupted. Make sure you only edit recorded areas.

●If feedback or howling occurs during TV playback, move the camcorder’s microphone away from the TV, or turn down the TV’s volume.

●If you change from 12-BIT to 16-BIT in mid-recording and then use the tape for Audio Dubbing, it is not effective from the point where 16-BIT recording began.

●During Audio Dubbing, when the tape moves to scenes recorded in the LP mode, scenes recorded in 16-BIT audio or a blank portion, Audio Dubbing stops.

●Audio dubbing is also possible using an optional microphone connected to the MIC connector.

●While an optional microphone is connected, the built-in microphone is disabled.

●To perform Audio Dubbing with a video unit connected to the camcorder’s S/AV connector, first set “S/AV INPUT” to “A/V.IN” or “S.IN” in VIDEO Menu. (
pg. 29, 32)

The “AUX” indication appears instead of “MIC”.

Insert Editing

You can record a new scene into a previously recorded tape, replacing a section of the original recording with minimal picture distortion at the in and outpoints. The original audio remains unchanged.

●Use the provided remote control or an optional remote control kit RM-V717KITU.

NOTES:

●Before performing the following steps, make sure that “TIME CODE” is set to “ON”. (
pg. 29, 33)

●Insert Editing is not possible on a tape recorded in the LP mode or on a blank portion of a tape.

1 Play back the tape, locate the Edit-Out point and press PAUSE (9). Confirm the time code at this point. (
pg. 19)

2 Press REW (3) until the Edit-In point is located, then press PAUSE (9).

3 Press and hold INSERT (I) on the remote control, then press PAUSE (9). The “9I” indicator and the Time Code (min.:sec.) appear and the camcorder enters Insert-Pause mode.

4 Press START/STOP to begin editing.

●Confirm the insert at the time code you checked in step 1.

●To pause editing, press START/STOP. Press it again to resume editing.

5 To end Insert Editing, press START/STOP, then STOP (8).

NOTES:

●Program AE with special effects (
pg. 38) can be used to spice up the scenes being edited during Insert Editing.

●During Insert Editing, the date and time information changes.

●If you perform Insert Editing onto a blank space on the tape, the audio and video may be disrupted. Make sure you only edit recorded areas.

●During Insert Editing, when the tape moves to scenes recorded in the LP mode or a blank portion, Insert Editing stops. (
pg. 50)

ADVANCED FEATURES