Panasonic AW-PH400P manual Connector Y, SDI connector SDI, L in connector G/L, Pb connector Pb

Page 11

Parts and their function

JY connector [Y]

This is the output connector for the camera’s video signals.

It is connected to the Y/VIDEO connector on the AW-RC400 cable compensation unit or monitor, etc. Use a BNC coaxial cable for the connecting cable. The AW-PB302 RGB card must be installed if the AW-E300, AW-E300A, AW-E600, AW-E800 or AW-E800A convertible camera is to be used.

K1394 connector [1394]

This is used for the control of the convertible camera and pan/tilt head equipped with an IEEE1394 card such as the AW-PB310.

Use an IEEE1394 cable for the connecting cable.

LSDI connector [SDI]

This is the output connector for the camera’s video signals.

When the AW-PB504 SDI card or other card is inserted in the convertible camera for use, SDI signals can be output.

Use a BNC coaxial cable for the connecting cable.

MG/L IN connector [G/L IN]

This is the genlock signal input connector.

It is connected to the G/L OUT connector on the AW-RC400 cable compensation unit or other unit. Use a BNC coaxial cable for the connecting cable.

NPROMPTER IN connector [PROMPTER IN]

The video signals for the prompter are input to this connector.

Use a BNC coaxial cable for the connecting cable.

OPb connector [Pb]

This is the output connector for the camera’s video signals.

It is connected to the Pb connector on the AW-RC400 cable compensation unit or monitor, etc.

Use a BNC coaxial cable for the connecting cable.

PPr/C connector [Pr/C]

This is the output connector for the camera’s video signals.

It is connected to the Pr/C connector on the AW-RC400 cable compensation unit or monitor, etc.

Use a BNC coaxial cable for the connecting cable.

Indoor Pan/Tilt Head AW-PH400

AW-PH400

11

Image 11

Contents AW-PH400 AW-RP400 AW-RC400 AW-RL400 AW-RL400FCC Note Safety precautionsImportant Safety Instructions Contents ≥ Handle the units carefully Operating precautions≥ Do not use the units outdoors ≥ Maintenance Introduction AccessoriesPrecautions for use Installation precautions Parts and their function Tally lamp accessory Rotary head connector panel Pedestal connector panelPedestal Power ON/OFF switch Bottom panel Prompter connectorOption connector Option ND/EXT connector ND/EXT@ SDI in connector SDI Lens I/F 2 connector Lens I/FL in connector G/L Connector YConnector SDI connector SDIAttaching the camera mounting base For a stand-alone installationFor installation on the ceiling $ Assembling the pan/tilt headMounting the tally lamp For installation on the ceiling $ Setting the mounting direction switchFor stand-alone installation $ Setting the PCB switches $ Installing the pan/tilt head $ Mounting the camera ≥ Camera AW-E650, AW-E350 $ Attaching the wire≥ Camera AW-E750 Replacing the consumable parts Supply voltage SpecificationsPower consumption Memo Rack-mounting adaptors Mounting screws M4!8 mm Zoom switch Plug D-SUB 15-pin for tally/INCOM system$ Front panel Focus indicator PAN Position indicatorIris indicator = Zoom indicatorLCD panel Preset Memory selection buttons 1 toPAN/TILT lever/ROTATION control switch Memory button$ Rear panel EXT Cont IN/OUT connectorsCamera Control in from RCB P1 to P5 connectors TALLY/INCOM connectorCamera Control in from ROP connector Remote connectorControl OUT to PAN/TILT Head P1 to P5 connectors Moni SEL OUT connector$ Operation method Menu settingsMenu item Setting Description Initial value $ List of menu items and settingsIris Control setting BOTH/RP400/CB400 Tilt Range setting 190/300 degreesSpeed with Zoom POS. setting OFF/1/2/3 Preset Speed setting 1 toMemory Length setting 60s/120s/300s/600s Option Switch a to H settingsSD Card setting Control Select Mode setting INTERLOCK/UN-INTERLOCKBuzzer setting OFF/ON Auto RUN setting Start No., END No., IntervalHow to mount the AW-RP400 in a rack Before changing the position, turn off the power How to change the position of the connector panelSecure the zoom switch using the four screws How to replace the zoom switchBefore replacing the zoom switch, turn off the power Replacing the consumable parts Supply voltage DC 12.0 Power consumption Approx W Cable Compensation Unit AW-RC400 SHORT/LONG selector switch Front panel Power LEDPower switch Cable length setting switches 0 toPb in connectors 1 to MONITOR1, 2 connectors BAC adaptor storage spaceVideo in connectors 1 to = Pr/C in connectors 1 toHow to mount the AW-RC400 in a rack Ambient operating temperature Power consumption Approx WPan/tilt head connecting cable Roll unit anchoring screw holes Pan/tilt head connectorRotary ring Camera mounting screw U1/4-20UNC Camera mounting plate a BInstallation When the AW-E655 is used as the camera When the AW-E750, AW-E650 or AW-E350 is used as the cameraCamera mounting plate’s screws Performance Supply voltage DC 24 Power consumption Approx WPan/tilt head connector Connections Zoom/focus Control MONITOR1 MONITOR2 Example of system configuration$ Turning on the power Operating procedures$ Providing cable compensation for the cameras Setting the recording time and number of memories $ Genlock adjustments for the respective cameras$ Video adjustments for the cameras $ Tracing memory settingsPlaying the tracing memory data Erasing the tracing memory data $ Setting the preset memory dataRegistering the preset memory data Changing the tracing memory dataPlaying the preset memory data Cable specifications Cable specifications When an RD lens made by Fujinon is used Page Page Page Panasonic Broadcast & Television Systems Company