Panasonic AW-PH400P, AW-RP400N, AW-RC400N $ Mounting the camera, For a stand-alone installation

Page 17

Indoor Pan/Tilt Head AW-PH400

Installation (Be sure to ask your dealer to install the unit.)

$ Mounting the camera

When mounting the camera on the pan/tilt head, be very careful to ensure that the camera does not fall off or fall down.

1Mount the lens onto the convertible camera. (Before mounting a large lens, consult with your dealer.)

2Insert the rubber piece between the camera and pan/tilt head, and mount the convertible camera after aligning it with the guide pins. Use a tool to tighten up the mounting screws so that they are securely tightened.

For a stand-alone installation

Set the guide pin.

Mount the camera with the mounting screws.

Rubber piece

Mounting screws

AW-PH400

For installation on the ceiling

Set the guide pin.

Mount the camera with the mounting screws.

Rubber piece

Mounting screws

❈Be absolutely sure to use a screwdriver or other tool to tighten the two camera mounting screws so that the camera is secured firmly.

❈After the camera has been mounted, check that there is no play in the way it was mounted.

17

Image 17

Contents AW-PH400 AW-RP400 AW-RC400 AW-RL400 AW-RL400FCC Note Safety precautionsImportant Safety Instructions Contents ≥ Handle the units carefully Operating precautions≥ Do not use the units outdoors ≥ Maintenance Introduction AccessoriesPrecautions for use Installation precautions Parts and their function Pedestal Power ON/OFF switch Rotary head connector panel Pedestal connector panelBottom panel Prompter connector Tally lamp accessory@ SDI in connector SDI ND/EXT connector ND/EXTLens I/F 2 connector Lens I/F Option connector OptionConnector Connector YSDI connector SDI L in connector G/LFor installation on the ceiling For a stand-alone installation$ Assembling the pan/tilt head Attaching the camera mounting baseMounting the tally lamp For installation on the ceiling $ Setting the mounting direction switchFor stand-alone installation $ Setting the PCB switches $ Installing the pan/tilt head $ Mounting the camera ≥ Camera AW-E650, AW-E350 $ Attaching the wire≥ Camera AW-E750 Replacing the consumable parts Supply voltage SpecificationsPower consumption Memo Rack-mounting adaptors Mounting screws M4!8 mm Zoom switch Plug D-SUB 15-pin for tally/INCOM system$ Front panel Iris indicator PAN Position indicator= Zoom indicator Focus indicatorPAN/TILT lever/ROTATION control switch Preset Memory selection buttons 1 toMemory button LCD panelCamera Control in from RCB P1 to P5 connectors EXT Cont IN/OUT connectorsTALLY/INCOM connector $ Rear panelControl OUT to PAN/TILT Head P1 to P5 connectors Remote connectorMoni SEL OUT connector Camera Control in from ROP connector$ Operation method Menu settingsMenu item Setting Description Initial value $ List of menu items and settingsSpeed with Zoom POS. setting OFF/1/2/3 Tilt Range setting 190/300 degreesPreset Speed setting 1 to Iris Control setting BOTH/RP400/CB400Memory Length setting 60s/120s/300s/600s Option Switch a to H settingsBuzzer setting OFF/ON Control Select Mode setting INTERLOCK/UN-INTERLOCKAuto RUN setting Start No., END No., Interval SD Card settingHow to mount the AW-RP400 in a rack Before changing the position, turn off the power How to change the position of the connector panelSecure the zoom switch using the four screws How to replace the zoom switchBefore replacing the zoom switch, turn off the power Replacing the consumable parts Supply voltage DC 12.0 Power consumption Approx W Cable Compensation Unit AW-RC400 Power switch Front panel Power LEDCable length setting switches 0 to SHORT/LONG selector switchVideo in connectors 1 to MONITOR1, 2 connectors BAC adaptor storage space= Pr/C in connectors 1 to Pb in connectors 1 toHow to mount the AW-RC400 in a rack Ambient operating temperature Power consumption Approx WPan/tilt head connecting cable Rotary ring Camera mounting screw U1/4-20UNC Pan/tilt head connectorCamera mounting plate a B Roll unit anchoring screw holesInstallation When the AW-E655 is used as the camera When the AW-E750, AW-E650 or AW-E350 is used as the cameraCamera mounting plate’s screws Performance Supply voltage DC 24 Power consumption Approx WPan/tilt head connector Connections Zoom/focus Control MONITOR1 MONITOR2 Example of system configuration$ Turning on the power Operating procedures$ Providing cable compensation for the cameras $ Video adjustments for the cameras $ Genlock adjustments for the respective cameras$ Tracing memory settings Setting the recording time and number of memoriesPlaying the tracing memory data Registering the preset memory data $ Setting the preset memory dataChanging the tracing memory data Erasing the tracing memory dataPlaying the preset memory data Cable specifications Cable specifications When an RD lens made by Fujinon is used Page Page Page Panasonic Broadcast & Television Systems Company