Panasonic AW-RP400N, AW-RC400N, AW-PH400P manual Introduction, Accessories, Precautions for use

Page 6

Indoor Pan/Tilt Head AW-PH400

Introduction

The stand-alone indoor pan/tilt head can be rotated through 300 degrees in the vertical direction and 400 degrees in the horizontal direction.

Operations can be performed at high speeds of up to 90 degrees per second.

Equipment such as a camera and lens with a total weight of 17.6 lbs (8 kg) can be mounted on the unit.

The camera can also be rotated using the AW-RL400 roll unit available as an option.

The shooting positions and settings for up to 50 positions can be registered as preset memory data.

NOTE

The AW-PH400 cannot be controlled from the AW-RP301, AW-RP305, AW-RP501, AW-RP505, AW-RP605 or AW-RP605A controller.

In order to protect the environment when the pan/tilt head is to be discarded at the end of its service life, ask a specialized contractor to dispose of it properly.

Accessories

 

Rotary arm

1

Camera mounting base

1

Rotary arm and camera base mounting screws (with flat washers)

 

M5!22 mm

7

Camera cable

1

Tally lamp

1

Tally mounting screws (M3!6 mm)

2

Blank panel for tally

1

Wire mounting screws (with flat washers, spring washers)

 

M4!8 mm

1

M4!6 mm

1

Hexagon key wrench

1

AC cable

1

Rubber piece

1

Precautions for use

The AW-PH400 uses a manganese dioxide-lithium battery (CR2032).

Before discarding the pan/tilt head or its printed circuit boards, be absolutely sure to remove the battery.

Be absolutely sure to dispose of the removed battery in accordance with the applicable domestic laws and regulations.

Do not throw out the battery along with the general household garbage.

For the procedure to remove the battery, refer to the section on replacing the battery in “Replacing the consumable parts” (page 19).

Replace the lithium battery here.

6

Image 6
Contents AW-RL400 AW-PH400 AW-RP400 AW-RC400 AW-RL400Safety precautions FCC NoteImportant Safety Instructions Contents Operating precautions ≥ Do not use the units outdoors ≥ Maintenance≥ Handle the units carefully Accessories Precautions for useIntroduction Installation precautions Parts and their function Bottom panel Prompter connector Rotary head connector panel Pedestal connector panelPedestal Power ON/OFF switch Tally lamp accessoryLens I/F 2 connector Lens I/F ND/EXT connector ND/EXT@ SDI in connector SDI Option connector OptionSDI connector SDI Connector YConnector L in connector G/L$ Assembling the pan/tilt head For a stand-alone installationFor installation on the ceiling Attaching the camera mounting baseMounting the tally lamp $ Setting the mounting direction switch For stand-alone installationFor installation on the ceiling $ Setting the PCB switches $ Installing the pan/tilt head $ Mounting the camera $ Attaching the wire ≥ Camera AW-E750≥ Camera AW-E650, AW-E350 Replacing the consumable parts Specifications Power consumptionSupply voltage Memo Zoom switch Plug D-SUB 15-pin for tally/INCOM system Rack-mounting adaptors Mounting screws M4!8 mm$ Front panel = Zoom indicator PAN Position indicatorIris indicator Focus indicatorMemory button Preset Memory selection buttons 1 toPAN/TILT lever/ROTATION control switch LCD panelTALLY/INCOM connector EXT Cont IN/OUT connectorsCamera Control in from RCB P1 to P5 connectors $ Rear panelMoni SEL OUT connector Remote connectorControl OUT to PAN/TILT Head P1 to P5 connectors Camera Control in from ROP connectorMenu settings $ Operation method$ List of menu items and settings Menu item Setting Description Initial valuePreset Speed setting 1 to Tilt Range setting 190/300 degreesSpeed with Zoom POS. setting OFF/1/2/3 Iris Control setting BOTH/RP400/CB400Option Switch a to H settings Memory Length setting 60s/120s/300s/600sAuto RUN setting Start No., END No., Interval Control Select Mode setting INTERLOCK/UN-INTERLOCKBuzzer setting OFF/ON SD Card settingHow to mount the AW-RP400 in a rack How to change the position of the connector panel Before changing the position, turn off the powerHow to replace the zoom switch Before replacing the zoom switch, turn off the powerSecure the zoom switch using the four screws Replacing the consumable parts Supply voltage DC 12.0 Power consumption Approx W Cable Compensation Unit AW-RC400 Cable length setting switches 0 to Front panel Power LEDPower switch SHORT/LONG selector switch= Pr/C in connectors 1 to MONITOR1, 2 connectors BAC adaptor storage spaceVideo in connectors 1 to Pb in connectors 1 toHow to mount the AW-RC400 in a rack Power consumption Approx W Ambient operating temperaturePan/tilt head connecting cable Camera mounting plate a B Pan/tilt head connectorRotary ring Camera mounting screw U1/4-20UNC Roll unit anchoring screw holesInstallation When the AW-E750, AW-E650 or AW-E350 is used as the camera When the AW-E655 is used as the cameraCamera mounting plate’s screws Supply voltage DC 24 Power consumption Approx W Pan/tilt head connectorPerformance Connections Zoom/focus Control Example of system configuration MONITOR1 MONITOR2Operating procedures $ Turning on the power$ Providing cable compensation for the cameras $ Tracing memory settings $ Genlock adjustments for the respective cameras$ Video adjustments for the cameras Setting the recording time and number of memoriesPlaying the tracing memory data Changing the tracing memory data $ Setting the preset memory dataRegistering the preset memory data Erasing the tracing memory dataPlaying the preset memory data Cable specifications Cable specifications When an RD lens made by Fujinon is used Page Page Page Panasonic Broadcast & Television Systems Company