Panasonic AW-RC400N, AW-RP400N, AW-PH400P manual Operating procedures, $ Turning on the power

Page 52

Operating procedures

$ Turning on the power

1When using one AW-RP400, set its EXT CONT [M/S] switch to the [M] position.

When two AW-RP400 units are used, set the EXT CONT [M/S] switch on the AW-RP400 to which the pan/tilt head is connected to the [M] (master) position and the switch on the AW-RP400 to which the pan/tilt head is not connected to the [S] (slave) position.

2Turn on the power.

Follow the sequence below to turn on the power when one AW-RP400 is going to be used: Set the power switch of the AC adaptor used for the AW-RP400 and the AC power switch on the AW-PH400 to [ON], set the OPERATE switch on the AW-CB400 to [ON], and then set the OPERATE switch on the AW-RP400 to [ON].

Follow the sequence below to turn on the power when two AW-RP400 units are going to be used: Set the OPERATE switches of the AW-CB400 and of the AW-RP400 set as the slave to [ON], and then set the OPERATE switch on the AW-RP400 set as the master to [ON].

$ Setting the movement range (limiters) of the AW-PH400 indoor pan/tilt head

If there are any objects obstructing the movement of the AW-PH400 indoor pan/tilt head in the immediate vicinity, set restrictions on the movement range (limiters: left, right, top and bottom limits of rotation).

When the AW-RL400 roll unit is connected to the AW-RP400, set the movement limits (clockwise and counterclockwise limits) of the roll unit as well.

Before using these units, set these limits without fail.

When it is shipped, the AW-PH400 is set up to be placed on a stand or base. If it is to be suspended from the ceiling, the mounting direction switch must be set without fail. If this setting is not performed correctly, the directions of the pan/tilt operations will be reversed, and the movement range (limiter) settings of the pan/tilt head will not be stored in the memory properly. For details on the setting methods and related aspects, refer to “Setting the mounting direction switch” in the operating instructions for the AW-PH400.

Now proceed with the settings for the AW-RP400 pan/tilt control panel.

1Use the CONTROL SELECT buttons to select the pan/tilt head whose movement range (limiters) is to be set.

2To set the left limit, use the PAN/TILT lever to rotate the pan/tilt head as far as the left limit which is to be set. While holding down the MENU/LIMIT button, press the PRESET MEMORY button [5].

Once the limit is set, the lamp of the PRESET MEMORY button [45] will light.

To release the setting, press the PRESET MEMORY button [5] again while holding down the MENU/LIMIT button. Once the setting is released, the lamp of the PRESET MEMORY button [50] will light.

3To set the right limit, use the PAN/TILT lever to rotate the pan/tilt head as far as the right limit which is to be set. While holding down the MENU/LIMIT button, press the PRESET MEMORY button [10].

Once the limit is set, the lamp of the PRESET MEMORY button [45] will light.

To release the setting, press the PRESET MEMORY button [10] again while holding down the MENU/LIMIT button. Once the setting is released, the lamp of the PRESET MEMORY button [50] will light.

4To set the top limit, use the PAN/TILT lever to rotate the pan/tilt head as far as the top limit which is to be set. While holding down the MENU/LIMIT button, press the PRESET MEMORY button [15].

Once the limit is set, the lamp of the PRESET MEMORY button [45] will light.

To release the setting, press the PRESET MEMORY button [15] again while holding down the MENU/LIMIT button. Once the setting is released, the lamp of the PRESET MEMORY button [50] will light.

5To set the bottom limit, use the PAN/TILT lever to rotate the pan/tilt head as far as the bottom limit which is to be set. While holding down the MENU/LIMIT button, press the PRESET MEMORY button [20].

Once the limit is set, the lamp of the PRESET MEMORY button [45] will light.

To release the setting, press the PRESET MEMORY button [20] again while holding down the MENU/LIMIT button. Once the setting is released, the lamp of the PRESET MEMORY button [50] will light.

52

Image 52
Contents AW-RL400 AW-PH400 AW-RP400 AW-RC400 AW-RL400Safety precautions FCC NoteImportant Safety Instructions Contents ≥ Do not use the units outdoors ≥ Maintenance Operating precautions≥ Handle the units carefully Precautions for use AccessoriesIntroduction Installation precautions Parts and their function Rotary head connector panel Pedestal connector panel Pedestal Power ON/OFF switchBottom panel Prompter connector Tally lamp accessoryND/EXT connector ND/EXT @ SDI in connector SDILens I/F 2 connector Lens I/F Option connector OptionConnector Y ConnectorSDI connector SDI L in connector G/LFor a stand-alone installation For installation on the ceiling$ Assembling the pan/tilt head Attaching the camera mounting baseMounting the tally lamp For stand-alone installation $ Setting the mounting direction switchFor installation on the ceiling $ Setting the PCB switches $ Installing the pan/tilt head $ Mounting the camera ≥ Camera AW-E750 $ Attaching the wire≥ Camera AW-E650, AW-E350 Replacing the consumable parts Power consumption SpecificationsSupply voltage Memo Zoom switch Plug D-SUB 15-pin for tally/INCOM system Rack-mounting adaptors Mounting screws M4!8 mm$ Front panel PAN Position indicator Iris indicator= Zoom indicator Focus indicatorPreset Memory selection buttons 1 to PAN/TILT lever/ROTATION control switchMemory button LCD panelEXT Cont IN/OUT connectors Camera Control in from RCB P1 to P5 connectorsTALLY/INCOM connector $ Rear panelRemote connector Control OUT to PAN/TILT Head P1 to P5 connectorsMoni SEL OUT connector Camera Control in from ROP connectorMenu settings $ Operation method$ List of menu items and settings Menu item Setting Description Initial valueTilt Range setting 190/300 degrees Speed with Zoom POS. setting OFF/1/2/3Preset Speed setting 1 to Iris Control setting BOTH/RP400/CB400Option Switch a to H settings Memory Length setting 60s/120s/300s/600sControl Select Mode setting INTERLOCK/UN-INTERLOCK Buzzer setting OFF/ONAuto RUN setting Start No., END No., Interval SD Card settingHow to mount the AW-RP400 in a rack How to change the position of the connector panel Before changing the position, turn off the powerBefore replacing the zoom switch, turn off the power How to replace the zoom switchSecure the zoom switch using the four screws Replacing the consumable parts Supply voltage DC 12.0 Power consumption Approx W Cable Compensation Unit AW-RC400 Front panel Power LED Power switchCable length setting switches 0 to SHORT/LONG selector switchMONITOR1, 2 connectors BAC adaptor storage space Video in connectors 1 to= Pr/C in connectors 1 to Pb in connectors 1 toHow to mount the AW-RC400 in a rack Power consumption Approx W Ambient operating temperaturePan/tilt head connecting cable Pan/tilt head connector Rotary ring Camera mounting screw U1/4-20UNCCamera mounting plate a B Roll unit anchoring screw holesInstallation When the AW-E750, AW-E650 or AW-E350 is used as the camera When the AW-E655 is used as the cameraCamera mounting plate’s screws Pan/tilt head connector Supply voltage DC 24 Power consumption Approx WPerformance Connections Zoom/focus Control Example of system configuration MONITOR1 MONITOR2Operating procedures $ Turning on the power$ Providing cable compensation for the cameras $ Genlock adjustments for the respective cameras $ Video adjustments for the cameras$ Tracing memory settings Setting the recording time and number of memoriesPlaying the tracing memory data $ Setting the preset memory data Registering the preset memory dataChanging the tracing memory data Erasing the tracing memory dataPlaying the preset memory data Cable specifications Cable specifications When an RD lens made by Fujinon is used Page Page Page Panasonic Broadcast & Television Systems Company