Panasonic AW-RP400N, AW-RC400N, AW-PH400P manual Installation

Page 45

Roll Unit AW-RL400

Installation

1Attach the pan/tilt head’s rotary arm to the roll unit using the three mounting screws (M5!22 mm, with flat washers, pan/tilt head accessory).

2Attach the rotary arm to the pan/tilt head using the mounting screws (M5!22 mm, with flat washers, pan/tilt head accessory).

Roll unit

Rotary arm

Camera mounting plate (consisting of 2 separate sub plates)

AW-RL400

3Loosen the two screws of camera mounting plate which is already installed to the roll unit. Then remove the camera mounting plate.

Camera mounting plate (consisting of 2 separate sub plates)

Screws

❈When assembling the units, use the Allen key (provided), wrench and screwdriver, and secure the units by tightening the screws firmly. After mounting the units, check there is no play in the way they are mounted.

45

Image 45

Contents AW-PH400 AW-RP400 AW-RC400 AW-RL400 AW-RL400FCC Note Safety precautionsImportant Safety Instructions Contents Operating precautions ≥ Do not use the units outdoors ≥ Maintenance≥ Handle the units carefully Accessories Precautions for useIntroduction Installation precautions Parts and their function Pedestal Power ON/OFF switch Rotary head connector panel Pedestal connector panelBottom panel Prompter connector Tally lamp accessory@ SDI in connector SDI ND/EXT connector ND/EXTLens I/F 2 connector Lens I/F Option connector OptionConnector Connector YSDI connector SDI L in connector G/LFor installation on the ceiling For a stand-alone installation$ Assembling the pan/tilt head Attaching the camera mounting baseMounting the tally lamp $ Setting the mounting direction switch For stand-alone installationFor installation on the ceiling $ Setting the PCB switches $ Installing the pan/tilt head $ Mounting the camera $ Attaching the wire ≥ Camera AW-E750≥ Camera AW-E650, AW-E350 Replacing the consumable parts Specifications Power consumptionSupply voltage Memo Rack-mounting adaptors Mounting screws M4!8 mm Zoom switch Plug D-SUB 15-pin for tally/INCOM system$ Front panel Iris indicator PAN Position indicator= Zoom indicator Focus indicatorPAN/TILT lever/ROTATION control switch Preset Memory selection buttons 1 toMemory button LCD panelCamera Control in from RCB P1 to P5 connectors EXT Cont IN/OUT connectorsTALLY/INCOM connector $ Rear panelControl OUT to PAN/TILT Head P1 to P5 connectors Remote connectorMoni SEL OUT connector Camera Control in from ROP connector$ Operation method Menu settingsMenu item Setting Description Initial value $ List of menu items and settingsSpeed with Zoom POS. setting OFF/1/2/3 Tilt Range setting 190/300 degreesPreset Speed setting 1 to Iris Control setting BOTH/RP400/CB400Memory Length setting 60s/120s/300s/600s Option Switch a to H settingsBuzzer setting OFF/ON Control Select Mode setting INTERLOCK/UN-INTERLOCKAuto RUN setting Start No., END No., Interval SD Card settingHow to mount the AW-RP400 in a rack Before changing the position, turn off the power How to change the position of the connector panelHow to replace the zoom switch Before replacing the zoom switch, turn off the powerSecure the zoom switch using the four screws Replacing the consumable parts Supply voltage DC 12.0 Power consumption Approx W Cable Compensation Unit AW-RC400 Power switch Front panel Power LEDCable length setting switches 0 to SHORT/LONG selector switchVideo in connectors 1 to MONITOR1, 2 connectors BAC adaptor storage space= Pr/C in connectors 1 to Pb in connectors 1 toHow to mount the AW-RC400 in a rack Ambient operating temperature Power consumption Approx WPan/tilt head connecting cable Rotary ring Camera mounting screw U1/4-20UNC Pan/tilt head connectorCamera mounting plate a B Roll unit anchoring screw holesInstallation When the AW-E655 is used as the camera When the AW-E750, AW-E650 or AW-E350 is used as the cameraCamera mounting plate’s screws Supply voltage DC 24 Power consumption Approx W Pan/tilt head connectorPerformance Connections Zoom/focus Control MONITOR1 MONITOR2 Example of system configuration$ Turning on the power Operating procedures$ Providing cable compensation for the cameras $ Video adjustments for the cameras $ Genlock adjustments for the respective cameras$ Tracing memory settings Setting the recording time and number of memoriesPlaying the tracing memory data Registering the preset memory data $ Setting the preset memory dataChanging the tracing memory data Erasing the tracing memory dataPlaying the preset memory data Cable specifications Cable specifications When an RD lens made by Fujinon is used Page Page Page Panasonic Broadcast & Television Systems Company