Panasonic AW-PH400P, AW-RP400N, AW-RC400N manual Cable Compensation Unit AW-RC400

Page 38

Cable Compensation Unit AW-RC400

Introduction

The AW-RC400 is capable of providing cable compensation for analog composite, analog Y/C or analog component signals in five channels up to 500 meters (when the BELDEN 8281 connecting cable or its equivalent is used).

It features a 5µs advance function for the sync signals in order to provide easy support for a system (another cable compensation unit is required) in which the coaxial cable connected between this AW-RC400 cable compensation unit and the camera is longer than 500 meters.

NOTE

Input either sync signals to the sync signal input connector on the AW-RC400 cable compensation unit or input video signals to one of the video channels (input composite signals or Y signals with sync to video input connector 1). If neither of these signals is input, the monitor selection will not be controlled.

The AW-RC400 provides cable compensation for the three Y, Pr and Pb signal channels by means of a single control. This means that the Y, Pr and Pb signals cannot be adjusted separately. In the same way, the Y and C signals cannot be adjusted separately.

The AW-RC400 is a cable compensation unit and, as such, it does not come with signal conversion functions (for converting component signals into composite signals, for instance).

When the cable compensation unit is to be discarded at the end of its service life, ask a specialized contractor to dispose of it properly in order to protect the environment.

Accessories

 

Rack-mounting adaptors

2

Mounting screws (M4!8 mm)

4

38

Image 38
Contents AW-RL400 AW-PH400 AW-RP400 AW-RC400 AW-RL400Safety precautions FCC NoteImportant Safety Instructions Contents ≥ Handle the units carefully Operating precautions≥ Do not use the units outdoors ≥ Maintenance Introduction AccessoriesPrecautions for use Installation precautions Parts and their function Bottom panel Prompter connector Rotary head connector panel Pedestal connector panelPedestal Power ON/OFF switch Tally lamp accessoryLens I/F 2 connector Lens I/F ND/EXT connector ND/EXT@ SDI in connector SDI Option connector OptionSDI connector SDI Connector YConnector L in connector G/L$ Assembling the pan/tilt head For a stand-alone installationFor installation on the ceiling Attaching the camera mounting baseMounting the tally lamp For installation on the ceiling $ Setting the mounting direction switchFor stand-alone installation $ Setting the PCB switches $ Installing the pan/tilt head $ Mounting the camera ≥ Camera AW-E650, AW-E350 $ Attaching the wire≥ Camera AW-E750 Replacing the consumable parts Supply voltage SpecificationsPower consumption Memo Zoom switch Plug D-SUB 15-pin for tally/INCOM system Rack-mounting adaptors Mounting screws M4!8 mm$ Front panel = Zoom indicator PAN Position indicatorIris indicator Focus indicatorMemory button Preset Memory selection buttons 1 toPAN/TILT lever/ROTATION control switch LCD panelTALLY/INCOM connector EXT Cont IN/OUT connectorsCamera Control in from RCB P1 to P5 connectors $ Rear panelMoni SEL OUT connector Remote connectorControl OUT to PAN/TILT Head P1 to P5 connectors Camera Control in from ROP connectorMenu settings $ Operation method$ List of menu items and settings Menu item Setting Description Initial valuePreset Speed setting 1 to Tilt Range setting 190/300 degreesSpeed with Zoom POS. setting OFF/1/2/3 Iris Control setting BOTH/RP400/CB400Option Switch a to H settings Memory Length setting 60s/120s/300s/600sAuto RUN setting Start No., END No., Interval Control Select Mode setting INTERLOCK/UN-INTERLOCKBuzzer setting OFF/ON SD Card settingHow to mount the AW-RP400 in a rack How to change the position of the connector panel Before changing the position, turn off the powerSecure the zoom switch using the four screws How to replace the zoom switchBefore replacing the zoom switch, turn off the power Replacing the consumable parts Supply voltage DC 12.0 Power consumption Approx W Cable Compensation Unit AW-RC400 Cable length setting switches 0 to Front panel Power LEDPower switch SHORT/LONG selector switch= Pr/C in connectors 1 to MONITOR1, 2 connectors BAC adaptor storage spaceVideo in connectors 1 to Pb in connectors 1 toHow to mount the AW-RC400 in a rack Power consumption Approx W Ambient operating temperaturePan/tilt head connecting cable Camera mounting plate a B Pan/tilt head connectorRotary ring Camera mounting screw U1/4-20UNC Roll unit anchoring screw holesInstallation When the AW-E750, AW-E650 or AW-E350 is used as the camera When the AW-E655 is used as the cameraCamera mounting plate’s screws Performance Supply voltage DC 24 Power consumption Approx WPan/tilt head connector Connections Zoom/focus Control Example of system configuration MONITOR1 MONITOR2Operating procedures $ Turning on the power$ Providing cable compensation for the cameras $ Tracing memory settings $ Genlock adjustments for the respective cameras$ Video adjustments for the cameras Setting the recording time and number of memoriesPlaying the tracing memory data Changing the tracing memory data $ Setting the preset memory dataRegistering the preset memory data Erasing the tracing memory dataPlaying the preset memory data Cable specifications Cable specifications When an RD lens made by Fujinon is used Page Page Page Panasonic Broadcast & Television Systems Company