Panasonic AW-RP400N, AW-RC400N $ Assembling the pan/tilt head, Attaching the camera mounting base

Page 12

Indoor Pan/Tilt Head AW-PH400

Installation (Be sure to ask your dealer to install the unit.)

$ Assembling the pan/tilt head

When assembling the pan/tilt head, use the Allen key (provided) and screwdriver, and secure the head by tightening the screws firmly. After mounting the pan/tilt head, check there is no play in its installation.

1Attaching the camera mounting base

Attach the camera mounting base to the rotary arm using the three mounting screws (M5!22 mm, with flat washers) provided. The installation direction differs depending on how the base is installed.

2Attaching the rotary arm

Attach the rotary arm to the rotary head using the four mounting screws (M5!22 mm, with flat washers) provided. The installation direction differs depending on how the arm is installed.

For a stand-alone installation

Rotary head

Camera mounting base

Rotary arm

For installation on the ceiling

Change the guide pin and screw positions as shown in the figure below on the right, and then attach the camera mounting base to the rotary arm.

Camera Mounting base

Change the positions of the guide pins.

Rotary arm

Change the positions of the camera mounting screws.

Camera mounting base

Rotary head

12

Image 12
Contents AW-RL400 AW-PH400 AW-RP400 AW-RC400 AW-RL400Safety precautions FCC NoteImportant Safety Instructions Contents Operating precautions ≥ Do not use the units outdoors ≥ Maintenance≥ Handle the units carefully Accessories Precautions for useIntroduction Installation precautions Parts and their function Rotary head connector panel Pedestal connector panel Pedestal Power ON/OFF switchBottom panel Prompter connector Tally lamp accessoryND/EXT connector ND/EXT @ SDI in connector SDILens I/F 2 connector Lens I/F Option connector OptionConnector Y ConnectorSDI connector SDI L in connector G/LFor a stand-alone installation For installation on the ceiling$ Assembling the pan/tilt head Attaching the camera mounting baseMounting the tally lamp $ Setting the mounting direction switch For stand-alone installationFor installation on the ceiling $ Setting the PCB switches $ Installing the pan/tilt head $ Mounting the camera $ Attaching the wire ≥ Camera AW-E750≥ Camera AW-E650, AW-E350 Replacing the consumable parts Specifications Power consumptionSupply voltage Memo Zoom switch Plug D-SUB 15-pin for tally/INCOM system Rack-mounting adaptors Mounting screws M4!8 mm$ Front panel PAN Position indicator Iris indicator= Zoom indicator Focus indicatorPreset Memory selection buttons 1 to PAN/TILT lever/ROTATION control switchMemory button LCD panelEXT Cont IN/OUT connectors Camera Control in from RCB P1 to P5 connectorsTALLY/INCOM connector $ Rear panelRemote connector Control OUT to PAN/TILT Head P1 to P5 connectorsMoni SEL OUT connector Camera Control in from ROP connectorMenu settings $ Operation method$ List of menu items and settings Menu item Setting Description Initial valueTilt Range setting 190/300 degrees Speed with Zoom POS. setting OFF/1/2/3Preset Speed setting 1 to Iris Control setting BOTH/RP400/CB400Option Switch a to H settings Memory Length setting 60s/120s/300s/600sControl Select Mode setting INTERLOCK/UN-INTERLOCK Buzzer setting OFF/ONAuto RUN setting Start No., END No., Interval SD Card settingHow to mount the AW-RP400 in a rack How to change the position of the connector panel Before changing the position, turn off the powerHow to replace the zoom switch Before replacing the zoom switch, turn off the powerSecure the zoom switch using the four screws Replacing the consumable parts Supply voltage DC 12.0 Power consumption Approx W Cable Compensation Unit AW-RC400 Front panel Power LED Power switchCable length setting switches 0 to SHORT/LONG selector switchMONITOR1, 2 connectors BAC adaptor storage space Video in connectors 1 to= Pr/C in connectors 1 to Pb in connectors 1 toHow to mount the AW-RC400 in a rack Power consumption Approx W Ambient operating temperaturePan/tilt head connecting cable Pan/tilt head connector Rotary ring Camera mounting screw U1/4-20UNCCamera mounting plate a B Roll unit anchoring screw holesInstallation When the AW-E750, AW-E650 or AW-E350 is used as the camera When the AW-E655 is used as the cameraCamera mounting plate’s screws Supply voltage DC 24 Power consumption Approx W Pan/tilt head connectorPerformance Connections Zoom/focus Control Example of system configuration MONITOR1 MONITOR2Operating procedures $ Turning on the power$ Providing cable compensation for the cameras $ Genlock adjustments for the respective cameras $ Video adjustments for the cameras$ Tracing memory settings Setting the recording time and number of memoriesPlaying the tracing memory data $ Setting the preset memory data Registering the preset memory dataChanging the tracing memory data Erasing the tracing memory dataPlaying the preset memory data Cable specifications Cable specifications When an RD lens made by Fujinon is used Page Page Page Panasonic Broadcast & Television Systems Company