Panasonic AW-RP400N Remote connector, DC 12V in socket, Moni SEL OUT connector, Ground terminal

Page 27

Parts and their function

PREMOTE connector

Connect an external unit to this connector to control the pan/tilt head systems from a PC or other external unit. Connect the connector to the PC using the AW-CA50T9 RS-232C cable.

QDC 12V IN socket

Connect the AW-PS505 AC adaptor (sold separately) to this socket.

RCONTROL OUT TO PAN/TILT HEAD [P1] to [P5] connectors

Connect these connectors to the IP/RP connectors on the AW-PH400 indoor pan/tilt heads using 10BASE-T (equivalent to UTP category 5) straight cables. The cables can be extended up to a maximum of 500 meters.

SMONI SEL OUT connector

Connect this connector to the MONI SEL OUT connector on the AW-RC400 cable compensation unit using a 10BASE-T (equivalent to UTP category 5) straight cable. You can monitor the images of the system selected by the AW-RP400 from the MONITOR1 connector on the AW-RC400 and the images of the system selected by the AW-CB400 from the MONITOR2 connector on the AW-RC400.

If two AW-RP400 units are connected, you can monitor the images of the system selected by the master AW-RP400 from the MONITOR1 connector on the AW-RC400 and the images of the system selected by the slave AW-RP400 from the MONITOR2 connector on the AW-RC400.

TCAMERA CONTROL IN FROM ROP connector

Connect the AW-CB400 remote operation panel to this connector using the connecting cable packed with the AW-CB400.

The cameras installed on the pan/tilt heads can now be controlled from the AW-CB400.

UGround terminal

Connect this terminal to ground.

Pan/Tilt Control Panel AW-RP400

AW-RP400

27

Image 27
Contents AW-PH400 AW-RP400 AW-RC400 AW-RL400 AW-RL400FCC Note Safety precautionsImportant Safety Instructions Contents Operating precautions ≥ Do not use the units outdoors ≥ Maintenance≥ Handle the units carefully Accessories Precautions for useIntroduction Installation precautions Parts and their function Tally lamp accessory Rotary head connector panel Pedestal connector panelPedestal Power ON/OFF switch Bottom panel Prompter connectorOption connector Option ND/EXT connector ND/EXT@ SDI in connector SDI Lens I/F 2 connector Lens I/FL in connector G/L Connector YConnector SDI connector SDIAttaching the camera mounting base For a stand-alone installationFor installation on the ceiling $ Assembling the pan/tilt headMounting the tally lamp $ Setting the mounting direction switch For stand-alone installationFor installation on the ceiling $ Setting the PCB switches $ Installing the pan/tilt head $ Mounting the camera $ Attaching the wire ≥ Camera AW-E750≥ Camera AW-E650, AW-E350 Replacing the consumable parts Specifications Power consumptionSupply voltage Memo Rack-mounting adaptors Mounting screws M4!8 mm Zoom switch Plug D-SUB 15-pin for tally/INCOM system$ Front panel Focus indicator PAN Position indicatorIris indicator = Zoom indicatorLCD panel Preset Memory selection buttons 1 toPAN/TILT lever/ROTATION control switch Memory button$ Rear panel EXT Cont IN/OUT connectorsCamera Control in from RCB P1 to P5 connectors TALLY/INCOM connectorCamera Control in from ROP connector Remote connectorControl OUT to PAN/TILT Head P1 to P5 connectors Moni SEL OUT connector$ Operation method Menu settingsMenu item Setting Description Initial value $ List of menu items and settingsIris Control setting BOTH/RP400/CB400 Tilt Range setting 190/300 degreesSpeed with Zoom POS. setting OFF/1/2/3 Preset Speed setting 1 toMemory Length setting 60s/120s/300s/600s Option Switch a to H settingsSD Card setting Control Select Mode setting INTERLOCK/UN-INTERLOCKBuzzer setting OFF/ON Auto RUN setting Start No., END No., IntervalHow to mount the AW-RP400 in a rack Before changing the position, turn off the power How to change the position of the connector panelHow to replace the zoom switch Before replacing the zoom switch, turn off the powerSecure the zoom switch using the four screws Replacing the consumable parts Supply voltage DC 12.0 Power consumption Approx W Cable Compensation Unit AW-RC400 SHORT/LONG selector switch Front panel Power LEDPower switch Cable length setting switches 0 toPb in connectors 1 to MONITOR1, 2 connectors BAC adaptor storage spaceVideo in connectors 1 to = Pr/C in connectors 1 toHow to mount the AW-RC400 in a rack Ambient operating temperature Power consumption Approx WPan/tilt head connecting cable Roll unit anchoring screw holes Pan/tilt head connectorRotary ring Camera mounting screw U1/4-20UNC Camera mounting plate a BInstallation When the AW-E655 is used as the camera When the AW-E750, AW-E650 or AW-E350 is used as the cameraCamera mounting plate’s screws Supply voltage DC 24 Power consumption Approx W Pan/tilt head connectorPerformance Connections Zoom/focus Control MONITOR1 MONITOR2 Example of system configuration$ Turning on the power Operating procedures$ Providing cable compensation for the cameras Setting the recording time and number of memories $ Genlock adjustments for the respective cameras$ Video adjustments for the cameras $ Tracing memory settingsPlaying the tracing memory data Erasing the tracing memory data $ Setting the preset memory dataRegistering the preset memory data Changing the tracing memory dataPlaying the preset memory data Cable specifications Cable specifications When an RD lens made by Fujinon is used Page Page Page Panasonic Broadcast & Television Systems Company