Panasonic AW-RC400N, AW-RP400N manual When the AW-E750, AW-E650 or AW-E350 is used as the camera

Page 46

Roll Unit AW-RL400

Installation

4 Separate the camera mounting plate, which was removed in step 3, into its two sub plates.

≥ Separate the camera mounting plate into sub plate (A) and sub plate (B) by loosening the clamping screw.

Clamping screw

5Follow the steps below to mount the camera mounting sub plates, which were separated in step 4, onto the camera body.

When the AW-E750, AW-E650 or AW-E350 is used as the camera

(1)Remove the screw attached to camera mounting sub plate (A), and use it to mount camera mounting sub plate (B) onto the tripod mounting seat.

(2)Mount camera mounting sub plate (A) onto camera mounting sub plate (B).

When the AW-E655 is used as the camera

(1) Mount camera mounting sub plate (A) onto the tripod mounting seat using the two camera mounting screws.

❈Be absolutely sure to use a screwdriver or other tool to tighten the two camera mounting screws so that the camera mounting plate is secured firmly.

46

Image 46

Contents AW-RL400 AW-PH400 AW-RP400 AW-RC400 AW-RL400Safety precautions FCC NoteImportant Safety Instructions Contents ≥ Do not use the units outdoors ≥ Maintenance Operating precautions≥ Handle the units carefully Precautions for use AccessoriesIntroduction Installation precautions Parts and their function Bottom panel Prompter connector Rotary head connector panel Pedestal connector panelPedestal Power ON/OFF switch Tally lamp accessoryLens I/F 2 connector Lens I/F ND/EXT connector ND/EXT@ SDI in connector SDI Option connector OptionSDI connector SDI Connector YConnector L in connector G/L$ Assembling the pan/tilt head For a stand-alone installationFor installation on the ceiling Attaching the camera mounting baseMounting the tally lamp For stand-alone installation $ Setting the mounting direction switchFor installation on the ceiling $ Setting the PCB switches $ Installing the pan/tilt head $ Mounting the camera ≥ Camera AW-E750 $ Attaching the wire≥ Camera AW-E650, AW-E350 Replacing the consumable parts Power consumption SpecificationsSupply voltage Memo Zoom switch Plug D-SUB 15-pin for tally/INCOM system Rack-mounting adaptors Mounting screws M4!8 mm$ Front panel = Zoom indicator PAN Position indicatorIris indicator Focus indicatorMemory button Preset Memory selection buttons 1 toPAN/TILT lever/ROTATION control switch LCD panelTALLY/INCOM connector EXT Cont IN/OUT connectorsCamera Control in from RCB P1 to P5 connectors $ Rear panelMoni SEL OUT connector Remote connectorControl OUT to PAN/TILT Head P1 to P5 connectors Camera Control in from ROP connectorMenu settings $ Operation method$ List of menu items and settings Menu item Setting Description Initial valuePreset Speed setting 1 to Tilt Range setting 190/300 degreesSpeed with Zoom POS. setting OFF/1/2/3 Iris Control setting BOTH/RP400/CB400Option Switch a to H settings Memory Length setting 60s/120s/300s/600sAuto RUN setting Start No., END No., Interval Control Select Mode setting INTERLOCK/UN-INTERLOCKBuzzer setting OFF/ON SD Card settingHow to mount the AW-RP400 in a rack How to change the position of the connector panel Before changing the position, turn off the powerBefore replacing the zoom switch, turn off the power How to replace the zoom switchSecure the zoom switch using the four screws Replacing the consumable parts Supply voltage DC 12.0 Power consumption Approx W Cable Compensation Unit AW-RC400 Cable length setting switches 0 to Front panel Power LEDPower switch SHORT/LONG selector switch= Pr/C in connectors 1 to MONITOR1, 2 connectors BAC adaptor storage spaceVideo in connectors 1 to Pb in connectors 1 toHow to mount the AW-RC400 in a rack Power consumption Approx W Ambient operating temperaturePan/tilt head connecting cable Camera mounting plate a B Pan/tilt head connectorRotary ring Camera mounting screw U1/4-20UNC Roll unit anchoring screw holesInstallation When the AW-E750, AW-E650 or AW-E350 is used as the camera When the AW-E655 is used as the cameraCamera mounting plate’s screws Pan/tilt head connector Supply voltage DC 24 Power consumption Approx WPerformance Connections Zoom/focus Control Example of system configuration MONITOR1 MONITOR2Operating procedures $ Turning on the power$ Providing cable compensation for the cameras $ Tracing memory settings $ Genlock adjustments for the respective cameras$ Video adjustments for the cameras Setting the recording time and number of memoriesPlaying the tracing memory data Changing the tracing memory data $ Setting the preset memory dataRegistering the preset memory data Erasing the tracing memory dataPlaying the preset memory data Cable specifications Cable specifications When an RD lens made by Fujinon is used Page Page Page Panasonic Broadcast & Television Systems Company