Panasonic AW-RC400N manual Option Switch a to H settings, Memory Length setting 60s/120s/300s/600s

Page 31

Pan/Tilt Control Panel AW-RP400

Menu settings

OPTION SWITCH A to H settings

(NOT USE / DEF / WIP / HEATER/FAN / LAMP / OPTION / ND / EXT / AF)

The following functions can be allocated to OPTION buttons A to H. Different functions can be allocated for different pan/tilt heads.

NOT USE: The button is disabled.

DEF:This controls the ON and OFF states of the defroster function when using a pan/tilt head system equipped with this function.

Each time the button is pressed, ON is switched to OFF or vice versa.

When the defroster function is ON, the lamp of the button to which this function has been allocated is lighted; when it is OFF, the lamp is off.

WIP:This controls the ON and OFF states of the wiper function when using a pan/tilt head system equipped with this function.

Each time the button is pressed, ON is switched to OFF or vice versa.

When the wiper function is ON, the lamp of the button to which this function has been allocated is lighted; when it is OFF, the lamp is off.

HEATER/FAN: This controls the ON and OFF states of the heater/fan function when using a pan/tilt head system equipped with this function.

Each time the button is pressed, ON is switched to OFF or vice versa.

When the heater/fan function is ON, the lamp of the button to which this function has been allocated is lighted; when it is OFF, the lamp is off.

LAMP: This controls the ON/OFF switching of the power from the AC outlet which is used for the AC adaptor’s lamp when using an AC adaptor for a pan/tilt head provided with a lamp control function.

Each time the button is pressed, ON is switched to OFF or vice versa.

When the lamp is ON, the button to which the function is allocated lights; when it is OFF, the button goes off.

If the lamp fails at the ON setting, the button blinks.

OPTION: This controls the short-circuit and open-circuit states of the AC adaptor’s OPTION CONTROL OUT connector when using an AC adaptor for a pan/tilt head system equipped with the OPTION switch control function.

Each time the button is pressed, short circuit is switched to open circuit or vice versa.

When short-circuited, the lamp of the button to which this function has been allocated is lighted; when open-circuited, the lamp is off.

ND:This controls the ON and OFF states of the ND filter when using a lens equipped with an ND filter. Each time the button is pressed, ON is switched to OFF or vice versa.

When the ND filter is ON, the lamp of the button to which this function has been allocated is lighted; when it is OFF, the lamp is off.

EXT:This controls the ON and OFF states of the extender when using a lens equipped with an extender. Each time the button is pressed, ON is switched to OFF or vice versa.

When the extender is ON, the lamp of the button to which this function has been allocated is lighted; when it is OFF, the lamp is off.

AF:This controls the ON and OFF states of the auto focus function when using a lens equipped with this function.

Each time the button is pressed, ON is switched to OFF or vice versa.

When the auto focus function is ON, the lamp of the button to which this function has been allocated is lighted; when it is OFF, the lamp is off.

AW-RP400

MEMORY LENGTH setting (60s/120s/300s/600s)

This menu item is used to set the tracing memory data recording time and the number of memories. 60s : 60 sec. ! 10 memories

120s : 120 sec. ! 5 memories

300s : 300 sec. ! 2 memories

600s : 600 sec. ! 1 memory

When data has already been registered in a tracing memory, the setting for the recording time and number of memories cannot be changed. To reset a setting, delete the registered data in the tracing memory first.

31

Image 31
Contents AW-PH400 AW-RP400 AW-RC400 AW-RL400 AW-RL400FCC Note Safety precautionsImportant Safety Instructions Contents ≥ Do not use the units outdoors ≥ Maintenance Operating precautions≥ Handle the units carefully Precautions for use AccessoriesIntroduction Installation precautions Parts and their function Tally lamp accessory Rotary head connector panel Pedestal connector panelPedestal Power ON/OFF switch Bottom panel Prompter connectorOption connector Option ND/EXT connector ND/EXT@ SDI in connector SDI Lens I/F 2 connector Lens I/FL in connector G/L Connector YConnector SDI connector SDIAttaching the camera mounting base For a stand-alone installationFor installation on the ceiling $ Assembling the pan/tilt headMounting the tally lamp For stand-alone installation $ Setting the mounting direction switchFor installation on the ceiling $ Setting the PCB switches $ Installing the pan/tilt head $ Mounting the camera ≥ Camera AW-E750 $ Attaching the wire≥ Camera AW-E650, AW-E350 Replacing the consumable parts Power consumption SpecificationsSupply voltage Memo Rack-mounting adaptors Mounting screws M4!8 mm Zoom switch Plug D-SUB 15-pin for tally/INCOM system$ Front panel Focus indicator PAN Position indicatorIris indicator = Zoom indicatorLCD panel Preset Memory selection buttons 1 toPAN/TILT lever/ROTATION control switch Memory button$ Rear panel EXT Cont IN/OUT connectorsCamera Control in from RCB P1 to P5 connectors TALLY/INCOM connectorCamera Control in from ROP connector Remote connectorControl OUT to PAN/TILT Head P1 to P5 connectors Moni SEL OUT connector$ Operation method Menu settingsMenu item Setting Description Initial value $ List of menu items and settingsIris Control setting BOTH/RP400/CB400 Tilt Range setting 190/300 degreesSpeed with Zoom POS. setting OFF/1/2/3 Preset Speed setting 1 toMemory Length setting 60s/120s/300s/600s Option Switch a to H settingsSD Card setting Control Select Mode setting INTERLOCK/UN-INTERLOCKBuzzer setting OFF/ON Auto RUN setting Start No., END No., IntervalHow to mount the AW-RP400 in a rack Before changing the position, turn off the power How to change the position of the connector panelBefore replacing the zoom switch, turn off the power How to replace the zoom switchSecure the zoom switch using the four screws Replacing the consumable parts Supply voltage DC 12.0 Power consumption Approx W Cable Compensation Unit AW-RC400 SHORT/LONG selector switch Front panel Power LEDPower switch Cable length setting switches 0 toPb in connectors 1 to MONITOR1, 2 connectors BAC adaptor storage spaceVideo in connectors 1 to = Pr/C in connectors 1 toHow to mount the AW-RC400 in a rack Ambient operating temperature Power consumption Approx WPan/tilt head connecting cable Roll unit anchoring screw holes Pan/tilt head connectorRotary ring Camera mounting screw U1/4-20UNC Camera mounting plate a BInstallation When the AW-E655 is used as the camera When the AW-E750, AW-E650 or AW-E350 is used as the cameraCamera mounting plate’s screws Pan/tilt head connector Supply voltage DC 24 Power consumption Approx WPerformance Connections Zoom/focus Control MONITOR1 MONITOR2 Example of system configuration$ Turning on the power Operating procedures$ Providing cable compensation for the cameras Setting the recording time and number of memories $ Genlock adjustments for the respective cameras$ Video adjustments for the cameras $ Tracing memory settingsPlaying the tracing memory data Erasing the tracing memory data $ Setting the preset memory dataRegistering the preset memory data Changing the tracing memory dataPlaying the preset memory data Cable specifications Cable specifications When an RD lens made by Fujinon is used Page Page Page Panasonic Broadcast & Television Systems Company