Panasonic AW-RC400N, AW-RP400N, AW-PH400P manual Playing the tracing memory data

Page 55

Operating procedures

3Press the START POINT button.

The lamps of the buttons among TRACING MEMORY buttons 1 to 10 where data can be registered now light.

The lamps of the buttons with numbers exceeding the number of memories set by the MEMORY LENGTH menu setting do not light.

If the lamp of any button among the number of memories in which data can be set is off, it means that data has already been registered in the button. When registering data in such a button, delete the existing data in its memory first.

4Press the number of the button in which the data is to be registered.

Only the lamp of the button pressed now lights, and START button flashes. The pan/tilt head position and camera settings prevailing at this time are recorded as the start position of the tracing memory.

When the STOP button is now operated, the registration of the tracing memory data is canceled.

5Press the START button.

The lamp of the START button stops flashing and goes off, then the recording standby mode is established. If the STOP button is now operated, the registration of the tracing memory data is canceled.

6Since tracing memory recording starts at the point where the PAN, TILT, ZOOM or FOCUS control is operated, proceed to register the data.

The lamp of the START button stops flashing, and the lamp of the STOP button starts flashing. As a general rule, the time which can be stored in the memory is about 6 seconds for each of the PRESET MEMORY buttons No.1 to 10 and about 60 seconds for each of the PRESET MEMORY buttons No.11 to 30.

Starting with the No.10 button, the button lamps go off every 6 seconds to indicate the remaining time for recording in the memory. When the lamps of all the buttons have gone off, the buzzer sounds, and the registration of the tracing memory data is ended.

To suspend the recording of the tracing memory data at any time, press the STOP button.

The operations performed up to the moment when the recording was suspended are registered as the tracing memory data.

The buzzer sounds when the tracing memory data recording starts, is suspended or ends.

7If necessary, register the data in TRACING MEMORY buttons No.1 to 10.

8Select another pan/tilt head system using the CONTROL SELECT button, and proceed with the tracing memory data settings for the pan/tilt head system concerned. Repeat this step for all the pan/tilt head systems.

The tracing memory information is recorded in the pan/tilt heads and control panels.

If a pan/tilt head or control panel is replaced, re-register the data in the tracing memory.

Playing the tracing memory data

1Select the pan/tilt head system using one of the CONTROL SELECT buttons.

2Press the button in which the tracing memory data to be played is registered.

The pan/tilt head system is set to the start position registered in the tracing memory.

3After the pan/tilt head system has been set to the start position registered in the tracing memory and stopped, the operation of the data registered in the tracing memory can be started by pressing the button corresponding to the tracing memory in which that data is registered.

To suspend the play of the tracing memory data at any time, press the STOP button. Play is also suspended when the PAN, TILT, ZOOM or FOCUS control is operated.

The buzzer sounds when tracing memory play starts, is suspended or ends.

55

Image 55
Contents AW-PH400 AW-RP400 AW-RC400 AW-RL400 AW-RL400FCC Note Safety precautionsImportant Safety Instructions Contents ≥ Do not use the units outdoors ≥ Maintenance Operating precautions≥ Handle the units carefully Precautions for use AccessoriesIntroduction Installation precautions Parts and their function Tally lamp accessory Rotary head connector panel Pedestal connector panelPedestal Power ON/OFF switch Bottom panel Prompter connectorOption connector Option ND/EXT connector ND/EXT@ SDI in connector SDI Lens I/F 2 connector Lens I/FL in connector G/L Connector YConnector SDI connector SDIAttaching the camera mounting base For a stand-alone installationFor installation on the ceiling $ Assembling the pan/tilt headMounting the tally lamp For stand-alone installation $ Setting the mounting direction switchFor installation on the ceiling $ Setting the PCB switches $ Installing the pan/tilt head $ Mounting the camera ≥ Camera AW-E750 $ Attaching the wire≥ Camera AW-E650, AW-E350 Replacing the consumable parts Power consumption SpecificationsSupply voltage Memo Rack-mounting adaptors Mounting screws M4!8 mm Zoom switch Plug D-SUB 15-pin for tally/INCOM system$ Front panel Focus indicator PAN Position indicatorIris indicator = Zoom indicatorLCD panel Preset Memory selection buttons 1 toPAN/TILT lever/ROTATION control switch Memory button$ Rear panel EXT Cont IN/OUT connectorsCamera Control in from RCB P1 to P5 connectors TALLY/INCOM connectorCamera Control in from ROP connector Remote connectorControl OUT to PAN/TILT Head P1 to P5 connectors Moni SEL OUT connector$ Operation method Menu settingsMenu item Setting Description Initial value $ List of menu items and settingsIris Control setting BOTH/RP400/CB400 Tilt Range setting 190/300 degreesSpeed with Zoom POS. setting OFF/1/2/3 Preset Speed setting 1 toMemory Length setting 60s/120s/300s/600s Option Switch a to H settingsSD Card setting Control Select Mode setting INTERLOCK/UN-INTERLOCKBuzzer setting OFF/ON Auto RUN setting Start No., END No., IntervalHow to mount the AW-RP400 in a rack Before changing the position, turn off the power How to change the position of the connector panelBefore replacing the zoom switch, turn off the power How to replace the zoom switchSecure the zoom switch using the four screws Replacing the consumable parts Supply voltage DC 12.0 Power consumption Approx W Cable Compensation Unit AW-RC400 SHORT/LONG selector switch Front panel Power LEDPower switch Cable length setting switches 0 toPb in connectors 1 to MONITOR1, 2 connectors BAC adaptor storage spaceVideo in connectors 1 to = Pr/C in connectors 1 toHow to mount the AW-RC400 in a rack Ambient operating temperature Power consumption Approx WPan/tilt head connecting cable Roll unit anchoring screw holes Pan/tilt head connectorRotary ring Camera mounting screw U1/4-20UNC Camera mounting plate a BInstallation When the AW-E655 is used as the camera When the AW-E750, AW-E650 or AW-E350 is used as the cameraCamera mounting plate’s screws Pan/tilt head connector Supply voltage DC 24 Power consumption Approx WPerformance Connections Zoom/focus Control MONITOR1 MONITOR2 Example of system configuration$ Turning on the power Operating procedures$ Providing cable compensation for the cameras Setting the recording time and number of memories $ Genlock adjustments for the respective cameras$ Video adjustments for the cameras $ Tracing memory settingsPlaying the tracing memory data Erasing the tracing memory data $ Setting the preset memory dataRegistering the preset memory data Changing the tracing memory dataPlaying the preset memory data Cable specifications Cable specifications When an RD lens made by Fujinon is used Page Page Page Panasonic Broadcast & Television Systems Company