Panasonic WV-NS202A Audio output volume PC to Camera, Audio output port PC to Camera

Page 50

[Audio output volume (PC to Camera)]

Select a volume level on the camera to hear audio transmitted from the PC.

Low/Middle/High

Default: Middle

[Audio output interval (PC to Camera)]

Select an interval for audio transmission from the follow- ing.

160 msec/320 msec/640 msec/1280 msec Default: 640 msec

Notes:

When a shorter interval is selected, the delay time will be shorter. When a longer interval is selected, audio interruption may be diminished even though the delay time will be longer.

Select the interval according to the network environ- ment.

Audio may temporarily be interrupted or noise may be heard when panning, tilting or zooming the cam- era, or when multiple users are accessing concur- rently. It may be possible to diminish the interruption or noise by setting a longer interval for "Audio output interval (PC to Camera)".

[Audio output port (PC to Camera)]

Enter the transmission port number (the port number on the camera used to receive audio data transmitted from the PC).

Available port number: 1024 - 50000 (Only even num- bers are available.)

Default: 34004

Note:

The transmission port number entered for "Audio output port (PC to Camera)" will be used only when "Unicast (MANUAL)" is selected for "Transmission type" (page 36).

When "OFF" is selected for "MPEG-4 transmission" (page 36) or when "Unicast (AUTO)" or "Multicast" is selected for "Transmission type", it is not necessary to enter the transmission port num- ber.

[Authentication]

Select an access level for audio transmission/reception from the following. Refer to page 63 for further informa- tion about the access level.

Level 1 only/Level 2 or higher/All users Default: All users

Notes:

Images and audio will not be synchronized. Therefore, images and audio may not always match.

Audio may be interrupted depending on the network environment.

50

Image 50
Contents Network Operating Instructions Contents Trademarks and registered trademarks PrefaceAbout these operating instructions Viewer softwareStep Monitor images on a PCMonitor images from a single camera Refresh interval MPEG-4About the Live List button *1 1AUTO Mode *2SD button manual SD recording button *2 Zoom buttons *23BRIGHTNESS buttons *2 4PRESET *22Control pad/buttons *2 5Camera title@ Audio output button *3 @ SD recording status indicatorMic input button *3 @2Main area *2Monitor images from multiple cameras Record images on the SD memory card manually Action at an alarm occurrence Action at an alarm occurrenceAlarm type Notify of alarm occurrences by e-mailTransmit images onto an FTP server Save images on the SD memory card SD memory card UseDisplay the log list Prev Page button Number of the listed logsTOP button Next Page buttonDownload button Close buttonPlay button About the playbackNumber of the listed images REV Play buttonPrev Image button Stop buttonNext Image button FF/REW buttonsEquipped security functions Access restrictions by changing the Http portAbout the network security of the camera How to display the setup menu How to operate the setup menu About the setup menu window Maintenance button Network setup buttonSchedule setup button 3SetupConfigure the basic settings of the camera Basic setup Configure the basic settings BasicAlarm status port Alarm status update modeDefault Real time Default onConfigure the settings relating to the NTP server NTP SD memory card setup SD memory card information Step Image capture size VGA Image capture size QvgaFTP error Configure the settings relating to the logs LOGAlarm ManualOFF Save logs Card LOG tab SD memory card tab Logs and associated imagesSD memory Save trigger SD memory Overwrite Save logs CardDefault 5 fps Jpeg setupDefault VGA Image quality Refresh interval JpegDefault 3 sec Transmission type MPEG-4 setupDefault Normal Refresh interval MPEG-4 MPEG-4 transmissionDefault Multicast TTL Default Unicast port2 AudioDefault Multicast address Available value 1 DefaultCamera title on screen Default OFF Camera title on screen 0-9, A-ZDefault 1 min Image Hold Home positionTilt Angle Upside-downPan·Tilt degree/Zoom ratio display Auto Pan Image AdjustPreset Position Privacy ZoneSuper Dynamic About SUPER-D 3 Super Dynamic functionSimple Black & white mode Default AutoDefault on High Sensitivity up Default ATW1Blue Gain Default High Chroma gain levelRed Gain DNR Digital Noise ReductionSet mask areas Register the preset position Edit the settings of the registered preset positionPosition No Position Auto panMode Zone settingPrivacy zone Zone selectConfigure the settings relating to audio Audio Authentication Audio output volume PC to CameraDefault Middle Audio output interval PC to Camera Audio output port PC to CameraNumber of characters for the IP address 1 Configures the multi-screen settings Multi-screen setupIP address Alarm setup Configure the alarm settings Alarm setupConfigure the settings relating to the alarm Alarm Camera motion on alarm Command alarm Configure the settings relating to the alarm image Alarm image setupAUX name Configure the settings relating to the alarm out terminalAlarm output terminal setup Set the VMD areas VMD area Default OFF Detection sensitivity StatusSet the VMD areas for each preset position Delete the VMD area set for the designated preset position Default MiddleMail notification setup Panasonic alarm protocol Configure the settings relating to Panasonic alarm protocolPanasonic alarm protocol setup Password Retype password User authenticationDefault OFF User name Number of characters for the password 4 32 charHost authentication Default OFF Access levelConfigure the settings of the servers Server setup Configure the settings relating to the mail server MailDefault Passive FTP server address Configure the settings relating to the FTP server FTPFTP mode Number of characters for the FTP server addressNetwork setup Configuring the network settings Network setupConfigure the network settings Network Available port number 1 Default Port numbers already in use Default gatewayUnavailable IP addresses for the default gate- way Default Manual Primary DNS, Secondary DNSWAN Default OFF Host name Configure the settings relating to Ddns DdnsAccess interval Number of characters for the host name 1 64 charConfigure the settings relating to Snmp Snmp FTP periodic transmission Default OFF DirectoryFTP periodic transmission Number of characters for the directory name 1Interval Schedule setupHow to configure the schedule settings How to delete the set schedule How to set the schedules Check the system log System log Maintenance of the camera MaintenanceError message Upgrade the firmware Upgrade How to upgrade the firmwareInitialize Html data Initialize setup data and Html dataInitialize/restart the camera Initialization RestartAbout the displayed system log Error indications relating to SmtpError indications relating to FTP Category Indication DescriptionError indications relating to login Error indications relating to DdnsError indications relating to NTP Troubleshooting Cause/solutionSymptom Symptom Symptom Symptom Symptom Cause/solution Reference Pages Solutions Reference Pages Directory structure of drive B FTPGroup WAN IP address Protocol LAN IP address LAN port Setting example of the routerGroup LAN IP address LAN port WAN IP address Protocol N0407-0 3TR005115AAA
Related manuals
Manual 2 pages 19.41 Kb Manual 2 pages 61.33 Kb

WV-NS202A specifications

The Panasonic WV-NS202A is a high-performance network camera designed to provide advanced surveillance solutions for various security applications. With its plethora of features, cutting-edge technologies, and robust characteristics, this camera is ideal for both indoor and outdoor monitoring needs.

One of the standout features of the WV-NS202A is its 360-degree pan and 90-degree tilt capability, allowing for a comprehensive view of any given area. This unprecedented range of motion ensures maximum coverage while minimizing blind spots, making it suitable for large spaces such as shopping malls, airports, and corporate buildings. Additionally, the camera supports continuous rotation, enabling it to follow moving objects seamlessly.

The camera is equipped with a high-resolution imaging sensor that produces clear and detailed images, even in low-light conditions. The WV-NS202A employs advanced image processing technologies, including digital noise reduction and wide dynamic range, to enhance image quality further. This ensures that the camera captures accurate color reproduction and clarity, regardless of lighting scenarios, making it ideal for 24/7 surveillance.

In terms of connectivity, the WV-NS202A supports IP technology, allowing for easy integration into existing network infrastructures. The camera can deliver real-time video over a network, which can be accessed remotely from multiple devices, including smartphones, tablets, or computers. This remote accessibility is complemented by built-in web server functionality, enabling users to monitor video feeds and manage camera settings conveniently through a browser interface.

Panasonic has also prioritized security with the WV-NS202A, incorporating features such as user authentication, HTTPS encryption, and IP filtering. These comprehensive security measures ensure that video feeds are protected from unauthorized access, providing peace of mind for users.

Another notable characteristic of this camera is its durability. The WV-NS202A is designed to withstand various environmental conditions, boasting an IP66 rating for water and dust resistance. This makes it suitable for outdoor installations, where it can endure extreme weather conditions without compromising performance.

With its exceptional features, innovative technologies, and robust characteristics, the Panasonic WV-NS202A is a formidable solution for those seeking reliable security and surveillance. Its ease of use, coupled with advanced performance specifications, makes it an excellent choice for safeguarding assets and ensuring the safety of people in various environments.