Panasonic WV-NS202A operating instructions Troubleshooting, Cause/solution

Page 81

Troubleshooting

Before asking for repairs, check the symptoms on the following table.

Contact your dealer if a problem cannot be solved even after checking and trying the solution or if the problem is not described below.

Symptom

Cannot access from the browser.

Cause/solution

Is the LAN cable (category 5) firmly connected to the network connector on the rear of the camera?

Is the link LED right by the network connector lit? When it is not lit, connection to a LAN may not be established or a network may be not working correct- ly. Check if the cables have any contact failure or if the wiring is correct or not.

Is the power of the camera on?

Check if the power of the camera is turned on.

Are the set IP addresses valid?

Are you accessing the wrong IP address? Check the connection as follows:

With the Windows command prompt, > ping "IP address of the camera"

When the WV-NS202A replies, the camera is func- tioning normally.

If not, proceed either of the following.

Restart the camera and change the IP address by using the Panasonic IP setup software within 20 minutes after the restart.

Restart the camera while holding the [INITIAL SET] button on the rear of the camera. The cam- era will be initialized and the IP address will return to the default setting "192.168.0.10".

After the camera is initialized, access the camera and set the IP address again. (When the camera is initialized, all the settings of the camera previ- ously configured on the setup menus will be initial- ized.)

Reference

pages

Installation

Guide

Installation

Guide

Installation

Guide

67

78

81

Image 81
Contents Network Operating Instructions Contents About these operating instructions PrefaceTrademarks and registered trademarks Viewer softwareMonitor images from a single camera Monitor images on a PCStep Refresh interval MPEG-4About the Live SD button manual SD recording button *2 1AUTO Mode *2List button *1 Zoom buttons *22Control pad/buttons *2 4PRESET *23BRIGHTNESS buttons *2 5Camera titleMic input button *3 @ SD recording status indicator@ Audio output button *3 @2Main area *2Monitor images from multiple cameras Record images on the SD memory card manually Alarm type Action at an alarm occurrenceAction at an alarm occurrence Notify of alarm occurrences by e-mailTransmit images onto an FTP server SD memory card Use Save images on the SD memory cardDisplay the log list TOP button Number of the listed logsPrev Page button Next Page buttonClose button Download buttonNumber of the listed images About the playbackPlay button REV Play buttonNext Image button Stop buttonPrev Image button FF/REW buttonsAccess restrictions by changing the Http port About the network security of the cameraEquipped security functions How to display the setup menu How to operate the setup menu About the setup menu window Schedule setup button Network setup buttonMaintenance button 3SetupConfigure the basic settings Basic Configure the basic settings of the camera Basic setupDefault Real time Alarm status update modeAlarm status port Default onConfigure the settings relating to the NTP server NTP SD memory card setup SD memory card information Step Image capture size Qvga Image capture size VGAAlarm Configure the settings relating to the logs LOGFTP error ManualOFF LOG tab SD memory card tab Logs and associated images SD memory Save triggerSave logs Card Overwrite Save logs Card SD memoryDefault VGA Image quality Jpeg setupDefault 5 fps Refresh interval JpegDefault Normal Refresh interval MPEG-4 MPEG-4 setupDefault 3 sec Transmission type MPEG-4 transmissionDefault Multicast address Default Unicast port2 AudioDefault Multicast TTL Available value 1 DefaultDefault 1 min Image Hold Default OFF Camera title on screen 0-9, A-ZCamera title on screen Home positionUpside-down Pan·Tilt degree/Zoom ratio displayTilt Angle Preset Position Image AdjustAuto Pan Privacy ZoneAbout SUPER-D 3 Super Dynamic function Super DynamicDefault on High Sensitivity up Default AutoSimple Black & white mode Default ATW1Red Gain Default High Chroma gain levelBlue Gain DNR Digital Noise ReductionSet mask areas Edit the settings of the registered preset position Register the preset positionPosition No Auto pan PositionPrivacy zone Zone settingMode Zone selectConfigure the settings relating to audio Audio Default Middle Audio output interval PC to Camera Audio output volume PC to CameraAuthentication Audio output port PC to CameraConfigures the multi-screen settings Multi-screen setup IP addressNumber of characters for the IP address 1 Configure the alarm settings Alarm setup Configure the settings relating to the alarm AlarmAlarm setup Camera motion on alarm Command alarm Alarm image setup Configure the settings relating to the alarm imageConfigure the settings relating to the alarm out terminal Alarm output terminal setupAUX name Set the VMD areas VMD area Status Default OFF Detection sensitivitySet the VMD areas for each preset position Default Middle Delete the VMD area set for the designated preset positionMail notification setup Configure the settings relating to Panasonic alarm protocol Panasonic alarm protocol setupPanasonic alarm protocol Default OFF User name User authenticationPassword Retype password Number of characters for the password 4 32 charDefault OFF Access level Host authenticationConfigure the settings relating to the mail server Mail Configure the settings of the servers Server setupFTP mode Configure the settings relating to the FTP server FTPDefault Passive FTP server address Number of characters for the FTP server addressConfiguring the network settings Network setup Configure the network settings NetworkNetwork setup Unavailable IP addresses for the default gate- way Default gatewayAvailable port number 1 Default Port numbers already in use Default Manual Primary DNS, Secondary DNSWAN Access interval Configure the settings relating to Ddns DdnsDefault OFF Host name Number of characters for the host name 1 64 charConfigure the settings relating to Snmp Snmp FTP periodic transmission Default OFF DirectoryFTP periodic transmission Number of characters for the directory name 1Schedule setup How to configure the schedule settingsInterval How to delete the set schedule How to set the schedules Maintenance of the camera Maintenance Error messageCheck the system log System log How to upgrade the firmware Upgrade the firmware UpgradeInitialize/restart the camera Initialization Initialize setup data and Html dataInitialize Html data RestartError indications relating to FTP Error indications relating to SmtpAbout the displayed system log Category Indication DescriptionError indications relating to Ddns Error indications relating to NTPError indications relating to login Cause/solution TroubleshootingSymptom Symptom Symptom Symptom Symptom Cause/solution Reference Pages Solutions Reference Pages FTP Directory structure of drive BSetting example of the router Group LAN IP address LAN port WAN IP address ProtocolGroup WAN IP address Protocol LAN IP address LAN port N0407-0 3TR005115AAA
Related manuals
Manual 2 pages 19.41 Kb Manual 2 pages 61.33 Kb

WV-NS202A specifications

The Panasonic WV-NS202A is a high-performance network camera designed to provide advanced surveillance solutions for various security applications. With its plethora of features, cutting-edge technologies, and robust characteristics, this camera is ideal for both indoor and outdoor monitoring needs.

One of the standout features of the WV-NS202A is its 360-degree pan and 90-degree tilt capability, allowing for a comprehensive view of any given area. This unprecedented range of motion ensures maximum coverage while minimizing blind spots, making it suitable for large spaces such as shopping malls, airports, and corporate buildings. Additionally, the camera supports continuous rotation, enabling it to follow moving objects seamlessly.

The camera is equipped with a high-resolution imaging sensor that produces clear and detailed images, even in low-light conditions. The WV-NS202A employs advanced image processing technologies, including digital noise reduction and wide dynamic range, to enhance image quality further. This ensures that the camera captures accurate color reproduction and clarity, regardless of lighting scenarios, making it ideal for 24/7 surveillance.

In terms of connectivity, the WV-NS202A supports IP technology, allowing for easy integration into existing network infrastructures. The camera can deliver real-time video over a network, which can be accessed remotely from multiple devices, including smartphones, tablets, or computers. This remote accessibility is complemented by built-in web server functionality, enabling users to monitor video feeds and manage camera settings conveniently through a browser interface.

Panasonic has also prioritized security with the WV-NS202A, incorporating features such as user authentication, HTTPS encryption, and IP filtering. These comprehensive security measures ensure that video feeds are protected from unauthorized access, providing peace of mind for users.

Another notable characteristic of this camera is its durability. The WV-NS202A is designed to withstand various environmental conditions, boasting an IP66 rating for water and dust resistance. This makes it suitable for outdoor installations, where it can endure extreme weather conditions without compromising performance.

With its exceptional features, innovative technologies, and robust characteristics, the Panasonic WV-NS202A is a formidable solution for those seeking reliable security and surveillance. Its ease of use, coupled with advanced performance specifications, makes it an excellent choice for safeguarding assets and ensuring the safety of people in various environments.