Panasonic WV-NS202A operating instructions Solutions Reference Pages

Page 87

When using a PC on which Windows® XP Service Pack2 (SP2) is installed

The following may occur during operation when using a PC on which Windows® XP Service Pack2 (SP2) is installed. Follow the instructions below when the following has occurred. By performing the following solutions, other applica- tions and the security level may not be affected.

The "Information Bar" expressed in the following symptom and solutions will be displayed just below the address bar only when there is information to communicate.

Symptom

The following message is displayed on the information bar.

"Pop-up blocked. To see this pop-up or additional options, click here…"

The following message is displayed on the information bar. "This site might require the following Active X control: 'nwcv3setup.exe' from 'Matsushita Electric Industrial Co., Ltd'. Click here to install..."

An unnecessary status bar or scroll bar is displayed on the pop-up window.

Information Bar

 

Solutions

Reference

 

pages

 

 

Click the information bar and select "Always Allow

 

 

 

 

Pop-ups from This Site…". The dialog window saying

 

 

"Allow pop-ups from this site?" will be displayed. Click

 

the [Yes] button.

 

 

Click the information bar and select "Install Active X

 

 

 

 

Control".

 

 

The "Security Warning" window will be displayed.

 

 

Click the "Install" button on the displayed "Security

 

Warning" window.

 

 

Click "Internet Options" on the Tools menu of Internet

 

 

 

 

Explorer, and then click the [Security] tab. Then, click

 

 

the [Custom Level…] button to open the "Security

 

 

Setting" window. Under "Miscellaneous", select

 

"Enable" for "Allow script-initiated windows without

 

 

 

size or position constraints". Click the [OK] button.

 

 

The "Warning" window will be displayed. Click the

 

 

[Yes] button.

 

 

 

 

87

Image 87
Contents Network Operating Instructions Contents Viewer software PrefaceAbout these operating instructions Trademarks and registered trademarksRefresh interval MPEG-4 Monitor images on a PCMonitor images from a single camera StepAbout the Live Zoom buttons *2 1AUTO Mode *2SD button manual SD recording button *2 List button *15Camera title 4PRESET *22Control pad/buttons *2 3BRIGHTNESS buttons *2@2Main area *2 @ SD recording status indicatorMic input button *3 @ Audio output button *3Monitor images from multiple cameras Record images on the SD memory card manually Notify of alarm occurrences by e-mail Action at an alarm occurrenceAlarm type Action at an alarm occurrenceTransmit images onto an FTP server SD memory card Use Save images on the SD memory cardDisplay the log list Next Page button Number of the listed logsTOP button Prev Page buttonClose button Download buttonREV Play button About the playbackNumber of the listed images Play buttonFF/REW buttons Stop buttonNext Image button Prev Image buttonAccess restrictions by changing the Http port About the network security of the cameraEquipped security functions How to display the setup menu How to operate the setup menu About the setup menu window 3Setup Network setup buttonSchedule setup button Maintenance buttonConfigure the basic settings Basic Configure the basic settings of the camera Basic setupDefault on Alarm status update modeDefault Real time Alarm status portConfigure the settings relating to the NTP server NTP SD memory card setup SD memory card information Step Image capture size Qvga Image capture size VGAManual Configure the settings relating to the logs LOGAlarm FTP errorOFF LOG tab SD memory card tab Logs and associated images SD memory Save triggerSave logs Card Overwrite Save logs Card SD memoryRefresh interval Jpeg Jpeg setupDefault VGA Image quality Default 5 fpsMPEG-4 transmission MPEG-4 setupDefault Normal Refresh interval MPEG-4 Default 3 sec Transmission typeAvailable value 1 Default Default Unicast port2 AudioDefault Multicast address Default Multicast TTLHome position Default OFF Camera title on screen 0-9, A-ZDefault 1 min Image Hold Camera title on screenUpside-down Pan·Tilt degree/Zoom ratio displayTilt Angle Privacy Zone Image AdjustPreset Position Auto PanAbout SUPER-D 3 Super Dynamic function Super DynamicDefault ATW1 Default AutoDefault on High Sensitivity up Simple Black & white modeDNR Digital Noise Reduction Default High Chroma gain levelRed Gain Blue GainSet mask areas Edit the settings of the registered preset position Register the preset positionPosition No Auto pan PositionZone select Zone settingPrivacy zone ModeConfigure the settings relating to audio Audio Audio output port PC to Camera Audio output volume PC to CameraDefault Middle Audio output interval PC to Camera AuthenticationConfigures the multi-screen settings Multi-screen setup IP addressNumber of characters for the IP address 1 Configure the alarm settings Alarm setup Configure the settings relating to the alarm AlarmAlarm setup Camera motion on alarm Command alarm Alarm image setup Configure the settings relating to the alarm imageConfigure the settings relating to the alarm out terminal Alarm output terminal setupAUX name Set the VMD areas VMD area Status Default OFF Detection sensitivitySet the VMD areas for each preset position Default Middle Delete the VMD area set for the designated preset positionMail notification setup Configure the settings relating to Panasonic alarm protocol Panasonic alarm protocol setupPanasonic alarm protocol Number of characters for the password 4 32 char User authenticationDefault OFF User name Password Retype passwordDefault OFF Access level Host authenticationConfigure the settings relating to the mail server Mail Configure the settings of the servers Server setupNumber of characters for the FTP server address Configure the settings relating to the FTP server FTPFTP mode Default Passive FTP server addressConfiguring the network settings Network setup Configure the network settings NetworkNetwork setup Default Manual Primary DNS, Secondary DNS Default gatewayUnavailable IP addresses for the default gate- way Available port number 1 Default Port numbers already in useWAN Number of characters for the host name 1 64 char Configure the settings relating to Ddns DdnsAccess interval Default OFF Host nameConfigure the settings relating to Snmp Snmp Number of characters for the directory name 1 Default OFF DirectoryFTP periodic transmission FTP periodic transmissionSchedule setup How to configure the schedule settingsInterval How to delete the set schedule How to set the schedules Maintenance of the camera Maintenance Error messageCheck the system log System log How to upgrade the firmware Upgrade the firmware UpgradeRestart Initialize setup data and Html dataInitialize/restart the camera Initialization Initialize Html dataCategory Indication Description Error indications relating to SmtpError indications relating to FTP About the displayed system logError indications relating to Ddns Error indications relating to NTPError indications relating to login Cause/solution TroubleshootingSymptom Symptom Symptom Symptom Symptom Cause/solution Reference Pages Solutions Reference Pages FTP Directory structure of drive BSetting example of the router Group LAN IP address LAN port WAN IP address ProtocolGroup WAN IP address Protocol LAN IP address LAN port N0407-0 3TR005115AAA
Related manuals
Manual 2 pages 19.41 Kb Manual 2 pages 61.33 Kb