Panasonic WV-NS202A operating instructions Symptom

Page 82

Symptom

Cannot access from the browser.

Cannot obtain images on the SD memory card.

No image is displayed.

Images are displayed blurry.

Cause/solution

Is the same IP address provided to other devices? Are there contradictions between the address and the network subnet to be accessed?

<When the camera and the PC are connected in the same subnet>

Are the IP addresses of the camera and the PC set in a common subnet? Or is "Use Proxy Server" for the settings of the browser checked?

When accessing the camera in the same subnet, it is recommended to enter the address of the camera in the "Don’t Use Proxy For These Addresses" box.

<When the camera and the PC are connected in the different subnet>

Is the IP address of the default gateway set for the camera correct?

Is "Allow" selected for "FTP access" on the [Network] tab of "Network setup" page?

If not, select "Allow".

Is the entered password correct?

Restart the web browser and enter the password again.

Access to the SD memory card may be failed. Restart the browser and retry to obtain images.

Is the viewer software installed on a PC? Install the viewer software on a PC.

Is the version of DirectX 9.0c or later? Check the version of DirectX as follows.

1.Select "Run…" from the start menu of Windows®.

2.Enter "dxdiag" in the displayed dialog box and click the [OK] button.

If the version of DirectX is older than 9.0c, upgrade it.

Is there dust or dirt on the lens?

Check if there is dust or dirt on the lens.

Is the focus adjusted correctly?

Adjust the focus correctly by clicking the focus but- tons.

Reference

pages

68

29

29

3, 25

Installation

Guide

6

82

Image 82
Contents Network Operating Instructions Contents Trademarks and registered trademarks PrefaceAbout these operating instructions Viewer softwareStep Monitor images on a PCMonitor images from a single camera Refresh interval MPEG-4About the Live List button *1 1AUTO Mode *2SD button manual SD recording button *2 Zoom buttons *23BRIGHTNESS buttons *2 4PRESET *22Control pad/buttons *2 5Camera title@ Audio output button *3 @ SD recording status indicatorMic input button *3 @2Main area *2Monitor images from multiple cameras Record images on the SD memory card manually Action at an alarm occurrence Action at an alarm occurrenceAlarm type Notify of alarm occurrences by e-mailTransmit images onto an FTP server Save images on the SD memory card SD memory card UseDisplay the log list Prev Page button Number of the listed logsTOP button Next Page buttonDownload button Close buttonPlay button About the playbackNumber of the listed images REV Play buttonPrev Image button Stop buttonNext Image button FF/REW buttonsAbout the network security of the camera Access restrictions by changing the Http portEquipped security functions How to display the setup menu How to operate the setup menu About the setup menu window Maintenance button Network setup buttonSchedule setup button 3SetupConfigure the basic settings of the camera Basic setup Configure the basic settings BasicAlarm status port Alarm status update modeDefault Real time Default onConfigure the settings relating to the NTP server NTP SD memory card setup SD memory card information Step Image capture size VGA Image capture size QvgaFTP error Configure the settings relating to the logs LOGAlarm ManualOFF SD memory Save trigger LOG tab SD memory card tab Logs and associated imagesSave logs Card SD memory Overwrite Save logs CardDefault 5 fps Jpeg setupDefault VGA Image quality Refresh interval JpegDefault 3 sec Transmission type MPEG-4 setupDefault Normal Refresh interval MPEG-4 MPEG-4 transmissionDefault Multicast TTL Default Unicast port2 AudioDefault Multicast address Available value 1 DefaultCamera title on screen Default OFF Camera title on screen 0-9, A-ZDefault 1 min Image Hold Home positionPan·Tilt degree/Zoom ratio display Upside-downTilt Angle Auto Pan Image AdjustPreset Position Privacy ZoneSuper Dynamic About SUPER-D 3 Super Dynamic functionSimple Black & white mode Default AutoDefault on High Sensitivity up Default ATW1Blue Gain Default High Chroma gain levelRed Gain DNR Digital Noise ReductionSet mask areas Register the preset position Edit the settings of the registered preset positionPosition No Position Auto panMode Zone settingPrivacy zone Zone selectConfigure the settings relating to audio Audio Authentication Audio output volume PC to CameraDefault Middle Audio output interval PC to Camera Audio output port PC to CameraIP address Configures the multi-screen settings Multi-screen setupNumber of characters for the IP address 1 Configure the settings relating to the alarm Alarm Configure the alarm settings Alarm setupAlarm setup Camera motion on alarm Command alarm Configure the settings relating to the alarm image Alarm image setupAlarm output terminal setup Configure the settings relating to the alarm out terminalAUX name Set the VMD areas VMD area Default OFF Detection sensitivity StatusSet the VMD areas for each preset position Delete the VMD area set for the designated preset position Default MiddleMail notification setup Panasonic alarm protocol setup Configure the settings relating to Panasonic alarm protocolPanasonic alarm protocol Password Retype password User authenticationDefault OFF User name Number of characters for the password 4 32 charHost authentication Default OFF Access levelConfigure the settings of the servers Server setup Configure the settings relating to the mail server MailDefault Passive FTP server address Configure the settings relating to the FTP server FTPFTP mode Number of characters for the FTP server addressConfigure the network settings Network Configuring the network settings Network setupNetwork setup Available port number 1 Default Port numbers already in use Default gatewayUnavailable IP addresses for the default gate- way Default Manual Primary DNS, Secondary DNSWAN Default OFF Host name Configure the settings relating to Ddns DdnsAccess interval Number of characters for the host name 1 64 charConfigure the settings relating to Snmp Snmp FTP periodic transmission Default OFF DirectoryFTP periodic transmission Number of characters for the directory name 1How to configure the schedule settings Schedule setupInterval How to delete the set schedule How to set the schedules Error message Maintenance of the camera MaintenanceCheck the system log System log Upgrade the firmware Upgrade How to upgrade the firmwareInitialize Html data Initialize setup data and Html dataInitialize/restart the camera Initialization RestartAbout the displayed system log Error indications relating to SmtpError indications relating to FTP Category Indication DescriptionError indications relating to NTP Error indications relating to DdnsError indications relating to login Troubleshooting Cause/solutionSymptom Symptom Symptom Symptom Symptom Cause/solution Reference Pages Solutions Reference Pages Directory structure of drive B FTPGroup LAN IP address LAN port WAN IP address Protocol Setting example of the routerGroup WAN IP address Protocol LAN IP address LAN port N0407-0 3TR005115AAA
Related manuals
Manual 2 pages 19.41 Kb Manual 2 pages 61.33 Kb

WV-NS202A specifications

The Panasonic WV-NS202A is a high-performance network camera designed to provide advanced surveillance solutions for various security applications. With its plethora of features, cutting-edge technologies, and robust characteristics, this camera is ideal for both indoor and outdoor monitoring needs.

One of the standout features of the WV-NS202A is its 360-degree pan and 90-degree tilt capability, allowing for a comprehensive view of any given area. This unprecedented range of motion ensures maximum coverage while minimizing blind spots, making it suitable for large spaces such as shopping malls, airports, and corporate buildings. Additionally, the camera supports continuous rotation, enabling it to follow moving objects seamlessly.

The camera is equipped with a high-resolution imaging sensor that produces clear and detailed images, even in low-light conditions. The WV-NS202A employs advanced image processing technologies, including digital noise reduction and wide dynamic range, to enhance image quality further. This ensures that the camera captures accurate color reproduction and clarity, regardless of lighting scenarios, making it ideal for 24/7 surveillance.

In terms of connectivity, the WV-NS202A supports IP technology, allowing for easy integration into existing network infrastructures. The camera can deliver real-time video over a network, which can be accessed remotely from multiple devices, including smartphones, tablets, or computers. This remote accessibility is complemented by built-in web server functionality, enabling users to monitor video feeds and manage camera settings conveniently through a browser interface.

Panasonic has also prioritized security with the WV-NS202A, incorporating features such as user authentication, HTTPS encryption, and IP filtering. These comprehensive security measures ensure that video feeds are protected from unauthorized access, providing peace of mind for users.

Another notable characteristic of this camera is its durability. The WV-NS202A is designed to withstand various environmental conditions, boasting an IP66 rating for water and dust resistance. This makes it suitable for outdoor installations, where it can endure extreme weather conditions without compromising performance.

With its exceptional features, innovative technologies, and robust characteristics, the Panasonic WV-NS202A is a formidable solution for those seeking reliable security and surveillance. Its ease of use, coupled with advanced performance specifications, makes it an excellent choice for safeguarding assets and ensuring the safety of people in various environments.