Panasonic WV-NS202A Configure the settings relating to the alarm out terminal, AUX name

Page 56

Configure the settings relating to the alarm out terminal

Click the [Alarm] tab on the "Alarm setup" page. (☞ pages 20 and 21: How to display/operate the setup menu)

■Alarm output terminal setup

The settings relating to the alarm out terminal can be configured in this section. The settings for the alarm output ter- minal can be configured only when "Alarm output" is selected for "Terminal alarm 2" of "Alarm setup". Refer to pages 52, 53 and 55 for further information about the settings relating to the alarm, the camera action at an alarm occur- rence and the alarm image.

Note:

When "OPEN" is selected, the alarm signal will be output for around 20 seconds when the power of the camera is turned on.

[Pulse width]

When "Pulse" is selected for "Alarm output", select an alarm output terminal duration from the following. Available pulse width: 1 - 120 sec

Default: 1 sec

[Alarm output setup]

Select "ON" or "OFF" to determine whether or not to output the alarm signals to the alarm output terminal when an alarm is detected.

Default: OFF

[External terminal output setup]

Select "Latch" or "Pulse" for the alarm output terminal at an alarm occurrence.

Latch: When an alarm is detected, the alarm output ter- minal will be in the state selected for "Alarm output" until the alarm occurrence indication button is clicked.

Pulse: When an alarm is detected, the alarm output ter- minal will be in the state to the "Alarm output" setting for the period set for "Pulse width".

Default: Latch

[Alarm output]

Select "Open" or "Close" to determine whether to open or close the alarm output terminal when outputting the alarm signals.

OPEN: The alarm output terminal will open when out- putting the alarm signals. (Normally close)

CLOSE: The alarm output terminal will close when out- putting the alarm signals. (Normally open)

Default: OPEN

■AUX name

The names of "AUX", "OPEN" and "CLOSE" on the "Live" page can be changed.

[AUX (Up to 10 characters)]

Enter the name for "AUX" on the "Live" page.

[OPEN (Up to 5 characters)]

Enter the name for "OPEN" of "AUX" on the "Live" page.

[CLOSE (Up to 5 characters)]

Enter the name for "CLOSE" of "AUX" on the "Live" page.

56

Page 55 Page 57
Image 56
Page 55 Page 57
Contents Network Operating Instructions Contents Preface About these operating instructionsTrademarks and registered trademarks Viewer softwareMonitor images on a PC Monitor images from a single cameraStep Refresh interval MPEG-4About the Live 1AUTO Mode *2 SD button manual SD recording button *2List button *1 Zoom buttons *24PRESET *2 2Control pad/buttons *23BRIGHTNESS buttons *2 5Camera title@ SD recording status indicator Mic input button *3@ Audio output button *3 @2Main area *2Monitor images from multiple cameras Record images on the SD memory card manually Action at an alarm occurrence Alarm typeAction at an alarm occurrence Notify of alarm occurrences by e-mailTransmit images onto an FTP server Save images on the SD memory card SD memory card UseDisplay the log list Number of the listed logs TOP buttonPrev Page button Next Page buttonDownload button Close buttonAbout the playback Number of the listed imagesPlay button REV Play buttonStop button Next Image buttonPrev Image button FF/REW buttonsEquipped security functions Access restrictions by changing the Http portAbout the network security of the camera How to display the setup menu How to operate the setup menu About the setup menu window Network setup button Schedule setup buttonMaintenance button 3SetupConfigure the basic settings of the camera Basic setup Configure the basic settings BasicAlarm status update mode Default Real timeAlarm status port Default onConfigure the settings relating to the NTP server NTP SD memory card setup SD memory card information Step Image capture size VGA Image capture size QvgaConfigure the settings relating to the logs LOG AlarmFTP error ManualOFF Save logs Card LOG tab SD memory card tab Logs and associated imagesSD memory Save trigger SD memory Overwrite Save logs CardJpeg setup Default VGA Image qualityDefault 5 fps Refresh interval JpegMPEG-4 setup Default Normal Refresh interval MPEG-4Default 3 sec Transmission type MPEG-4 transmissionDefault Unicast port2 Audio Default Multicast addressDefault Multicast TTL Available value 1 DefaultDefault OFF Camera title on screen 0-9, A-Z Default 1 min Image HoldCamera title on screen Home positionTilt Angle Upside-downPan·Tilt degree/Zoom ratio display Image Adjust Preset PositionAuto Pan Privacy ZoneSuper Dynamic About SUPER-D 3 Super Dynamic functionDefault Auto Default on High Sensitivity upSimple Black & white mode Default ATW1Default High Chroma gain level Red GainBlue Gain DNR Digital Noise ReductionSet mask areas Register the preset position Edit the settings of the registered preset positionPosition No Position Auto panZone setting Privacy zoneMode Zone selectConfigure the settings relating to audio Audio Audio output volume PC to Camera Default Middle Audio output interval PC to CameraAuthentication Audio output port PC to CameraNumber of characters for the IP address 1 Configures the multi-screen settings Multi-screen setupIP address Alarm setup Configure the alarm settings Alarm setupConfigure the settings relating to the alarm Alarm Camera motion on alarm Command alarm Configure the settings relating to the alarm image Alarm image setupAUX name Configure the settings relating to the alarm out terminalAlarm output terminal setup Set the VMD areas VMD area Default OFF Detection sensitivity StatusSet the VMD areas for each preset position Delete the VMD area set for the designated preset position Default MiddleMail notification setup Panasonic alarm protocol Configure the settings relating to Panasonic alarm protocolPanasonic alarm protocol setup User authentication Default OFF User namePassword Retype password Number of characters for the password 4 32 charHost authentication Default OFF Access levelConfigure the settings of the servers Server setup Configure the settings relating to the mail server MailConfigure the settings relating to the FTP server FTP FTP modeDefault Passive FTP server address Number of characters for the FTP server addressNetwork setup Configuring the network settings Network setupConfigure the network settings Network Default gateway Unavailable IP addresses for the default gate- wayAvailable port number 1 Default Port numbers already in use Default Manual Primary DNS, Secondary DNSWAN Configure the settings relating to Ddns Ddns Access intervalDefault OFF Host name Number of characters for the host name 1 64 charConfigure the settings relating to Snmp Snmp Default OFF Directory FTP periodic transmissionFTP periodic transmission Number of characters for the directory name 1Interval Schedule setupHow to configure the schedule settings How to delete the set schedule How to set the schedules Check the system log System log Maintenance of the camera MaintenanceError message Upgrade the firmware Upgrade How to upgrade the firmwareInitialize setup data and Html data Initialize/restart the camera InitializationInitialize Html data RestartError indications relating to Smtp Error indications relating to FTPAbout the displayed system log Category Indication DescriptionError indications relating to login Error indications relating to DdnsError indications relating to NTP Troubleshooting Cause/solutionSymptom Symptom Symptom Symptom Symptom Cause/solution Reference Pages Solutions Reference Pages Directory structure of drive B FTPGroup WAN IP address Protocol LAN IP address LAN port Setting example of the routerGroup LAN IP address LAN port WAN IP address Protocol N0407-0 3TR005115AAA
Related manuals
Manual 2 pages 19.41 Kb Manual 2 pages 61.33 Kb

WV-NS202A specifications

The Panasonic WV-NS202A is a high-performance network camera designed to provide advanced surveillance solutions for various security applications. With its plethora of features, cutting-edge technologies, and robust characteristics, this camera is ideal for both indoor and outdoor monitoring needs.

One of the standout features of the WV-NS202A is its 360-degree pan and 90-degree tilt capability, allowing for a comprehensive view of any given area. This unprecedented range of motion ensures maximum coverage while minimizing blind spots, making it suitable for large spaces such as shopping malls, airports, and corporate buildings. Additionally, the camera supports continuous rotation, enabling it to follow moving objects seamlessly.

The camera is equipped with a high-resolution imaging sensor that produces clear and detailed images, even in low-light conditions. The WV-NS202A employs advanced image processing technologies, including digital noise reduction and wide dynamic range, to enhance image quality further. This ensures that the camera captures accurate color reproduction and clarity, regardless of lighting scenarios, making it ideal for 24/7 surveillance.

In terms of connectivity, the WV-NS202A supports IP technology, allowing for easy integration into existing network infrastructures. The camera can deliver real-time video over a network, which can be accessed remotely from multiple devices, including smartphones, tablets, or computers. This remote accessibility is complemented by built-in web server functionality, enabling users to monitor video feeds and manage camera settings conveniently through a browser interface.

Panasonic has also prioritized security with the WV-NS202A, incorporating features such as user authentication, HTTPS encryption, and IP filtering. These comprehensive security measures ensure that video feeds are protected from unauthorized access, providing peace of mind for users.

Another notable characteristic of this camera is its durability. The WV-NS202A is designed to withstand various environmental conditions, boasting an IP66 rating for water and dust resistance. This makes it suitable for outdoor installations, where it can endure extreme weather conditions without compromising performance.

With its exceptional features, innovative technologies, and robust characteristics, the Panasonic WV-NS202A is a formidable solution for those seeking reliable security and surveillance. Its ease of use, coupled with advanced performance specifications, makes it an excellent choice for safeguarding assets and ensuring the safety of people in various environments.
Top Page Image Contents