Panasonic AG-DVC 200E Preparation, Remove the battery holder, Attach the battery case to the unit

Page 11

Preparation

Using the AU-BP402 or AJ-BP490 battery pack made by Panasonic

Recharge the battery pack using the battery charger specifically designed for each individual battery pack. For the charging time and other details, refer to the operating instructions of the battery charger used.

ENGLISH

1 Remove the battery holder.

Disconnect these.

Battery holder

Disconnect these.

2 Attach the battery case to the unit.

1Connect the unit’s cable with the cable of the AU-M402H

battery case.

2Use a screwdriver to attach the AU-M402H battery case to the unit.

The holes for tightening the screws can be seen when the cover is opened and the rubber caps are raised. Use a screwdriver to tighten the screws, and attach the battery case to the unit. Ensure that the screws are tightened up as far as they will go.

<Note>

≥Do not pull the rubber caps with great force.

≥Be careful not to catch up the cables when attaching the battery case.

Screws

Rubber caps

3 Connect the plug of the battery pack to the connector inside the battery case, and insert the battery pack into the case.

Label surface

AU-BP402 battery pack

<Note>

Ensure that the power is turned off before connecting or disconnecting the plugs.

4 Set the battery type.

Select the battery type using <BATTERY> on the sub-menu screen.

Select “TYPE A” if the AJ-BP490 is to be used; select “NiCd12” if the AU-BP402 is to be used. (See page 34)

Connect here.

AU-M402H

battery case

 

10 (E)

Page 10 Page 12
Image 11
Page 10 Page 12
Contents
Digital Video Camera Recorder AG- ETo remove the battery/Verwijderen van de batterij Precautions for UseDo not Remove Panel Cover by Unscrewing Lithium BatteryVarning VaroitusContents Introduction FeaturesDigital Video Camera Recorder System configurationCleaning tape Rain cover Parts and their functions POWER/WARNING lamp Breaker switchMonitor volume control Reset button= Viewfinder connector Auto W/B white/black BAL switchGenlock in connector BNC Shutter switchExternal DC input socket DV I/F connector complying with Ieee StandardDC OUT DC power supply output socket Tally lampPreparation Remove the battery holderAttach the battery case to the unit Set the battery typeAttachBauer. the battery pack made by Anton Using a battery pack made by Anton BauerUsing the NP-1B battery pack made by Sony Attachunit. the battery made by Sony toPulllens. down the lens lever to secure Proceed with the flange back adjustment for the lensAttaching the lens Raise the lens lever, and remove the mount capDetaching the unit from the tripod attachment Attaching the shoulder belt optional accessoryMounting the unit on a tripod Attaching the viewfinder MicrophoneSpace ∏ Letters of the alphabet a through Z Setting the camera IDSetting the date and time White shading check Lens adjustments and checksFlange back adjustment White shading adjustmentViewfinder screen status displays Viewfinder displaysViewfinder lamp displays Extender display Switch settingsError result message Iris Mode switchShutter speed Temperature fineAdjustment amount Temperature display ATW, AWB channelSelecting the viewfinder screen display 50 Hz White balance and black balance adjustmentSet the switches to the positions shown in the figure Push the Auto W/B BAL switch to ABB and release itShutter modes Electronic shutter settingsSetting the synchro scanning mode PushSEL. the Shutter switch from on toSet the TCG switch Time data settingsSetting the user’s bit Setting the time codeEditing scene filenames Scene file setting methodScene files Scene file functionPress the Menu button to exit the menu operation How to use file selectReturning a scene filename to its default Rotate the JOG dial button to move to the Write itemList of file settings List of scene file settingsScene-to-scene continuity Set the camera unit’s switches as followsNormal recording Recording methodsAudio recording Selecting the audio input signalsAdjusting the audio recording level Select the desired input signals using the Audio in switchOther functions Connection to a PC capable of non-linear editing Using the unit with external componentsConnection to a video component with a DV connector Using the unit as a playerMenu operations Menu display enable/disableDisplaying sub-menus and deciding on settings Upon completion of the settings, press the Menu buttonMain 2/2 Setting menu configurationMain 1/2 Menu contents Additional Process SW ModeMain menu 1 of 2 main menu ProcessVTR Option BatteryVideo OUT VTR FunctionMARKER/ZEBRA Main menu 2 of 2 main menuMIC/AUDIO Lens ShadingVF Display 2/2 VF Display 1/2Camera ID DiagnosticLED GenlockHumid SlackREC Warning ServoEmergency eject Battery ENDBattery Near END Set the power to OFFError codes MaintenanceTape transport system SpecificationsVideo system Audio systemOther Optional accessory AJ-VF10Input OutputVQT9278-1 F0401T1051 @
Top Page Image Contents