Panasonic AG-DVC 200E CC/ND filter selector knob, MIC in mic input jack XLR, 3-pin, Lens lever

Page 9

Parts and their functions

 

@

?

 

 

>

 

=

<

1

 

ENGLISH

;

:

2

3

4

5

6

9 8 7

1 CC/ND filter selector knob

This is used to select the filter to match the subject brightness.

1:3200K

2:5600K+1/8ND

3:5600K

4:5600K+1/64ND

8MIC IN (mic input) jack (XLR, 3-pin)

The accessory microphone is connected to this jack. The power for the microphone is supplied from this jack.

9AUDIO OUT jacks (pin jacks)

An audio component is connected to these jacks. The sound for channel 1 and channel 2 is output separately.

2Lens lever

This lever is tightened to secure the lens after the lens has been attached to the lens mount.

3Lens mount (bayonet type)

The lens is attached to this mount.

4AUTO W/B (white/black) BAL switch

AWB : The white balance is automatically adjusted. When the AWB memory selector switch on the side panel is set to A or B and then the AUTO W/B BAL switch is operated, the adjustment value is recorded in the memory. Bear in mind that the switch does not work when it is set to the ATW or PRST position.

ABB : The black balance is automatically adjusted.

:GENLOCK IN connector (BNC)

Supply the sync signal (black burst signal) to this connector when gen-locking the camera pictures (CAM OUT jack) of the unit.

;CAM OUT jack

This is the dedicated output jack for the camera’s pictures.

<S-VIDEO OUT jack (Y/C jack)

When pictures are to be recorded with a backup VTR connected to the S-VIDEO OUT jack, bear in mind that the unit’s playback pictures will be recorded onto the backup VTR if any operation (such as REC CHECK) that performs VTR playback is executed.

5SHUTTER switch

This is the ON/OFF selector switch of the electronic shutter. OFF : The electronic shutter does not operate.

ON : The electronic shutter operates.

SEL : This is used when the electronic shutter speed is to be changed. The switch is a non-locking type. The shutter speed changes each time it is operated. For further details, refer to “Electronic shutter settings” (page 21).

6VTR START/STOP button

This starts or stops the video recording.

7LENS jack (12-pin)

The connecting cord of the lens is connected to this jack. For further details on the lenses that can be used, refer to the operating instructions of the lenses concerned.

=Viewfinder connector

The viewfinder plug is connected to this connector.

>Viewfinder stopper screw

This screw is used to secure the viewfinder.

?Light shoe

The video light or other such device is attached here.

@Shoulder belt fittings

The shoulder belt (optional accessory) is attached here.

8 (E)

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Digital Video Camera Recorder AG- ETo remove the battery/Verwijderen van de batterij Precautions for UseVarning Lithium BatteryVaroitus Do not Remove Panel Cover by UnscrewingContents Introduction FeaturesCleaning tape System configurationRain cover Digital Video Camera RecorderParts and their functions Monitor volume control Breaker switchReset button POWER/WARNING lampGenlock in connector BNC Auto W/B white/black BAL switchShutter switch = Viewfinder connectorDC OUT DC power supply output socket DV I/F connector complying with Ieee StandardTally lamp External DC input socketAttach the battery case to the unit Remove the battery holderSet the battery type PreparationUsing the NP-1B battery pack made by Sony Using a battery pack made by Anton BauerAttachunit. the battery made by Sony to AttachBauer. the battery pack made by AntonAttaching the lens Proceed with the flange back adjustment for the lensRaise the lens lever, and remove the mount cap Pulllens. down the lens lever to secureMounting the unit on a tripod Attaching the viewfinder Attaching the shoulder belt optional accessoryMicrophone Detaching the unit from the tripod attachmentSetting the camera ID Setting the date and timeSpace ∏ Letters of the alphabet a through Z Flange back adjustment Lens adjustments and checksWhite shading adjustment White shading checkViewfinder displays Viewfinder lamp displaysViewfinder screen status displays Error result message Switch settingsIris Mode switch Extender displayAdjustment amount Temperature fineTemperature display ATW, AWB channel Shutter speedSelecting the viewfinder screen display Set the switches to the positions shown in the figure White balance and black balance adjustmentPush the Auto W/B BAL switch to ABB and release it 50 HzSetting the synchro scanning mode Electronic shutter settingsPushSEL. the Shutter switch from on to Shutter modesSetting the user’s bit Time data settingsSetting the time code Set the TCG switchScene files Scene file setting methodScene file function Editing scene filenamesReturning a scene filename to its default How to use file selectRotate the JOG dial button to move to the Write item Press the Menu button to exit the menu operationList of file settings List of scene file settingsNormal recording Set the camera unit’s switches as followsRecording methods Scene-to-scene continuityAdjusting the audio recording level Selecting the audio input signalsSelect the desired input signals using the Audio in switch Audio recordingOther functions Connection to a video component with a DV connector Using the unit with external componentsUsing the unit as a player Connection to a PC capable of non-linear editingDisplaying sub-menus and deciding on settings Menu display enable/disableUpon completion of the settings, press the Menu button Menu operationsSetting menu configuration Main 1/2Main 2/2 Menu contents Main menu 1 of 2 main menu SW ModeProcess Additional ProcessVideo OUT BatteryVTR Function VTR OptionMIC/AUDIO Main menu 2 of 2 main menuLens Shading MARKER/ZEBRAVF Display 2/2 VF Display 1/2LED DiagnosticGenlock Camera IDREC Warning SlackServo HumidBattery Near END Battery ENDSet the power to OFF Emergency ejectError codes MaintenanceVideo system SpecificationsAudio system Tape transport systemInput Optional accessory AJ-VF10Output OtherVQT9278-1 F0401T1051 @
Top Page Image Contents