Panasonic AG-DVC 200E Shutter speed, LOW Light warning, Display Audio sampling, Frequency display

ENGLISH

Display item

What is displayed

Status causing the display to appear

8 Shutter speed

1/¢¢.¢

Displayed when the shutter speed has been set to SYNCHRO SCAN.

1/60 - 1/2000

Displayed when a fixed shutter speed has been set.

SUPER V

Displayed when SUPER V (high vertical resolution mode) has been set.

9 LOW LIGHT warning

LOW LIGHT

Displayed when the brightness has been reduced.

display

: AUDIO sampling

48k

Indicates that a frequency of 48 kHz has been selected.

frequency display

32k

Indicates that a frequency of 32 kHz has been selected.

<Note>

With a 1394 input, the input status is displayed.

; Audio level meter

Indicates the audio levels of CH1 and CH2 (see page 27).

display

< VTR warning

REC WARNING

Indicates the occurrence of an error during recording.

display/voltage

SLACK E-¢¢

Indicates the occurrence of an error caused by the mechanism. Depending

warning display

on the type of error, the power may be cut off automatically. (*1)

<Note>

For details on the codes displayed, refer to “Error codes” (page 40).

HUMID

Indicates that condensation has formed.

SERVO

Servo lock is not engaged during recording or playback.

RF

The signal level from the tape has dropped.

TAPE NEAR END

The tape is nearing its end (there are about 2 minutes left).

TAPE END

The tape has stopped at the tape end.

BATT NEAR END

The battery is nearly flat.

BATT END

The tape has stopped because the battery is flat.

MP TAPE

An MP tape has been loaded. The tape is automatically ejected.

BACKUP BATT EMPTY

It is time to replace the backup battery.

= FULL AUTO/SCENE

FULL

Displayed when the FULL AUTO switch has been set to ON.

FILE display

Filename which has been set

Indicates the filenames (8 characters) set for the scene files.

> AWB colour

AWB+¢¢

The adjustment amount is displayed when ON has been selected as the

temperature fine

“COLOUR TEMP” setting (see page 36) and the colour temperature has

adjustment amount

been adjusted finely. It is not displayed when OFF is selected or only ATW

display

has been set.

? Zoom display

Z00 - Z99

Indicates the zoom amount. However, most 1/2-inch size lenses have no

zoom position return. In such a case, this item is not displayed even if ON

has been selected as the display setting.

@ AWB colour

¢.¢K

Indicates the colour temperature.

temperature display

A ATW, AWB channel

Ach

The WHITE BAL switch has been set to channel A.

display

Bch

The WHITE BAL switch has been set to channel B.

PRE

The WHITE BAL switch has been set to PRE.

ATW

The full time auto white balance has been set.

B F value display

NC

Displayed when the lens cable has not been connected.

OPEN

Displayed when the lens iris has been opened.

F2.0 - F16

Indicates the lens iris value.

CLOSE

Displayed when the lens iris has been closed.

<Note>

This item appears when using a lens equipped with a function that displays

the aperture value.

C Gain display

0 - 36dB

Displays the current gain value.

D Filter display

FL1 - FL4

Displays the filter position.

FL–

Displayed when filter has not been set to the proper position.

E Calendar/clock

01-May-01 00:00:00

The 24-hour system is used for the clock display.

display

(Day-month-year and hours-minutes-seconds displayed)

F Voltage display

¢¢.¢V

The input voltage is displayed.

BAR display

B ∫∫∫∫

The number of “∫” squares serves as a rough guideline to indicate how

much battery charge remains. When the battery still has a sufficient charge,

four of these squares are displayed. These squares can be displayed

except when Type A or Type B has been selected as the <BATTERY

SELECT> setting on the BATTERY sub-menu. (See page 34)