Panasonic AG-DVC 200E Varning, Varoitus, Lithium Battery, Do not Remove Panel Cover by Unscrewing

Page 3

Precautions for Use

Lithium Battery

Warning

The lithium battery in this equipment must only be replaced by qualified personnel. When necessary, contact your local Panasonic supplier.

“The lithium battery is a critical component (type number CR2032 manufactured by Panasonic.)

It must never be subjected to excessive heat or discharge. It must therefore only be fitted in equipment designed specifically for its use.

Replacement batteries must be of the same type and manufacturer. They must be fitted in the same manner and location as the original battery, with the correct polarity connections observed.

Do not attempt to re-charge the old battery or re- use it for any other purpose. It should be disposed of in waste products destined for burial rather than incineration.”

ªDO NOT REMOVE PANEL COVER BY UNSCREWING.

To reduce the risk of electric shock, do not remove cover. No user serviceable parts inside.

Refer servicing to qualified service personnel.

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the equipment manufacturer. Discard used batteries according to manufacturer’s instructions.

VARNING

Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren. Kassera använt batteri enligt fabrikantens instruktion.

ADVARSEL!

Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandøren.

VAROITUS

Paristo voi räjähtää, jos se on virheellisesti asennettu.

Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyypiin. Hävitä käytetty paristo valmistajan ohjeiden mukaisesti.

CAUTION:

TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD AND ANNOYING INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY.

ENGLISH

WARNING:

TO REDUCE THE RISK OF FIRE OR SHOCK

HAZARD, KEEP THIS EQUIPMENT AWAY

FROM ALL LIQUIDS-USE AND STORE ONLY

IN LOCATIONS WHICH ARE NOT EXPOSED

TO THE RISK OF DRIPPING OR SPLASHING

LIQUIDS, AND DO NOT PLACE ANY LIQUID

CONTAINERS ON TOP OF THE EQUIPMENT.

indicates safety information.

This camera recorder is designed to be used exclusively with the standard size of DV tapes. Do not use DVCPRO tapes or other sizes of tapes.

2 (E)

Image 3

Contents Digital Video Camera Recorder AG- ETo remove the battery/Verwijderen van de batterij Precautions for UseDo not Remove Panel Cover by Unscrewing Lithium BatteryVarning VaroitusContents Introduction FeaturesDigital Video Camera Recorder System configurationCleaning tape Rain coverParts and their functions POWER/WARNING lamp Breaker switchMonitor volume control Reset button= Viewfinder connector Auto W/B white/black BAL switchGenlock in connector BNC Shutter switchExternal DC input socket DV I/F connector complying with Ieee StandardDC OUT DC power supply output socket Tally lampPreparation Remove the battery holderAttach the battery case to the unit Set the battery typeAttachBauer. the battery pack made by Anton Using a battery pack made by Anton BauerUsing the NP-1B battery pack made by Sony Attachunit. the battery made by Sony toPulllens. down the lens lever to secure Proceed with the flange back adjustment for the lensAttaching the lens Raise the lens lever, and remove the mount capDetaching the unit from the tripod attachment Attaching the shoulder belt optional accessoryMounting the unit on a tripod Attaching the viewfinder MicrophoneSetting the camera ID Setting the date and timeSpace ∏ Letters of the alphabet a through Z White shading check Lens adjustments and checksFlange back adjustment White shading adjustmentViewfinder displays Viewfinder lamp displaysViewfinder screen status displays Extender display Switch settingsError result message Iris Mode switchShutter speed Temperature fineAdjustment amount Temperature display ATW, AWB channelSelecting the viewfinder screen display 50 Hz White balance and black balance adjustmentSet the switches to the positions shown in the figure Push the Auto W/B BAL switch to ABB and release itShutter modes Electronic shutter settingsSetting the synchro scanning mode PushSEL. the Shutter switch from on toSet the TCG switch Time data settingsSetting the user’s bit Setting the time codeEditing scene filenames Scene file setting methodScene files Scene file functionPress the Menu button to exit the menu operation How to use file selectReturning a scene filename to its default Rotate the JOG dial button to move to the Write itemList of file settings List of scene file settingsScene-to-scene continuity Set the camera unit’s switches as followsNormal recording Recording methodsAudio recording Selecting the audio input signalsAdjusting the audio recording level Select the desired input signals using the Audio in switchOther functions Connection to a PC capable of non-linear editing Using the unit with external componentsConnection to a video component with a DV connector Using the unit as a playerMenu operations Menu display enable/disableDisplaying sub-menus and deciding on settings Upon completion of the settings, press the Menu buttonSetting menu configuration Main 1/2Main 2/2 Menu contents Additional Process SW ModeMain menu 1 of 2 main menu ProcessVTR Option BatteryVideo OUT VTR FunctionMARKER/ZEBRA Main menu 2 of 2 main menuMIC/AUDIO Lens ShadingVF Display 2/2 VF Display 1/2Camera ID DiagnosticLED GenlockHumid SlackREC Warning ServoEmergency eject Battery ENDBattery Near END Set the power to OFFError codes MaintenanceTape transport system SpecificationsVideo system Audio systemOther Optional accessory AJ-VF10Input OutputVQT9278-1 F0401T1051 @