Axis Communications thermal network camera user manual UPnPTM, RTP/H.264, Bonjour

Page 42

AXIS Q1931–E Thermal Network Camera

System Options

Depending on the level of security required, select the version on SNMP to use.

SNMP v1/v2 provides the lowest level of security. The community name can be specified as a password for read or read/write access to all supported SNMP devices. The default password for the Read community is public and the default password for the Write community is write.

Note

If HTTPS is enabled, SNMP v1 and SNMP v2c should be disabled.

Traps for SNMP v1/v2 are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

The following traps are available:

Cold start

Warm start

Link up

Authentication failed

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see HTTPS, on page 35. To enable SNMP v3, check the box and provide the initial user password.

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to Factory Default Settings, on page 46.

UPnPTM

The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

UPnPTM can be disabled under System Options > Network > UPnPTM.

RTP/H.264

The RTP port range and multicast settings are configured under System Options > Network > RTP.

The RTP port range defines the range of ports from which the video/audio ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used.

Select Always Multicast Video and/or Always Multicast Audio to start multicast streaming without opening an RTSP session.

Bonjour

The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

Bonjour can be disabled under System Options > Network > Bonjour.

42

Image 42
Contents Axis Q1931-E Thermal Network Camera Liability About this DocumentLegal Considerations Intellectual Property RightsSupport Learn MoreTable of Contents Axis Q1931-E Thermal Network CameraAudio Connector Connectors and ButtonsNetwork Connector Hardware OverviewSD Card Slot LED IndicatorsPower Connector Control ButtonAccess from a Browser Accessing the ProductAccessing the Product Start a browser Internet Explorer, Firefox, SafariLive View Accessing the Product Access from the InternetSet the Root Password Controls on the Live ViewManual Trigger Go to Setup EventsAxis Media Control viewer toolbar To show the manual trigger buttons in the Live ViewHalf-duplex mode AMC Audio ControlsMedia Streams How to Stream H.264Media Streams Axis Media Control AMCAlternative Methods of Accessing the Video Stream QuickTimeTM. The following paths can be usedAccessing Audio Streams Java applet supports simplex audio with G.711 encodingSetting Up the Product Setting Up the ProductBasic Setup Video Stream Video and AudioVideo and Audio Pixel CounterClick Save to apply the new settings Image264 Video and Audio Stream Profiles Camera SettingsExposure Settings OverlayGo to Video & Audio Overlay Image Using Overlay Text in an Action RuleOverlay Image Go to Events Action RulesAudio Modes Audio SettingsPrivacy Mask Audio InputAudio Clips Audio OutputAxis Q1931-E Thermal Network Camera Live View Config Live View ConfigDefault Viewer for Browsers User Defined Links Viewer SettingsGo to Setup Live View Config Output ButtonsActive/Inactive displays two buttons, one or each action Detectors Set Up Motion Detection WindowsDetectors Motion DetectionAudio Detection Motion Detection ParametersApplications Install ApplicationApplications Application LicensesAxis Q1931-E Thermal Network Camera Events EventsSetting Up an Action Rule Fallback ActionGo to Events Action Rules and click Add Recipient Use with action Setting Up an Email RecipientEvents Recipients Go to Events Recipients and click AddTo create a new schedule SchedulesRecurrences Go to Events Schedules and click AddRecording List RecordingsRecordings Continuous RecordingLanguages LanguagesSecurity System OptionsSystem Options UsersIeee CertificatesGo to System Options Security Ieee Date & Time Go to Setup System Options Security CertificatesClick Install certificate and upload the certificate Audio SupportBasic TCP/IP Settings System Options NetworkDNS Configuration Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service Axis Video Hosting System AvhsLink-Local IPv4 Address NTP ConfigurationHost Name Configuration NAT traversal port mapping for IPv4QoS Quality of Service FTPRTP/H.264 UPnPTM can be disabled under System Options Network UPnPTMUPnPTM BonjourNetwork Share System Options StorageSD Card Go to System Options Storage and click SD CardPorts MaintenancePorts & Devices Port StatusSystem Options Support AdvancedReset to Factory Default Settings Plain ConfigFile Upload Multi-Connector Cable sold separately Multi-Connector Cable sold separatelyFunction Pin Specifications Connector Emergency Recovery Procedure TroubleshootingTroubleshooting Checking the FirmwareSymptoms, Possible Causes and Remedial Actions Problems setting the IP addressProduct cannot be accessed from a browser Basic Product is accessible locally but not externallyProblems with streaming H.264 Key framesSettings Video and image problems, generalSetup Video & Audio Camera Settings Storage and disk management problemsTechnical Specifications Technical SpecificationsAlarm events Function/group Specifications Audio Audio streamingAlarm triggers InstallationPerformance Considerations Axis Q1931-E Thermal Network Camera M3.4