Axis Communications thermal network camera user manual Multi-Connector Cable sold separately

Page 47

AXIS Q1931–E Thermal Network Camera

Multi-Connector Cable (sold separately)

Multi-Connector Cable (sold separately)

When connecting external equipment to the Axis product, a multi-connector cable (available from Axis) is required in order to maintain the product’s IP rating. The multi-connector cable can be purchased from your Axis reseller.

Connect the multi-connector cable to the product’s multi-connector. To locate the multi-connector, see Hardware Overview, on page

5 . The cable provides the following connectors:

Note

See page 53 for technical specifications.

Power connector - 2-pin terminal block used for power input. The polarity of the cables does not matter. Use a limited power source (LPS) with either a rated output power limited to ≤100 W or a rated output current limited to ≤5 A.

Audio in (pink) - 3.5 mm input for a mono microphone, or a line-in mono signal (left channel is used from a stereo signal).

Audio out (green) - 3.5 mm output for audio (line level) that can be connected to a public address (PA) system or an active speaker with a built-in amplifier. A stereo connector must be used for the audio out.

I/O terminal connector - Use with external devices in combination with, for example, tampering alarms, motion detection, event triggering, time lapse recording and alarm notifications. In addition to ground and auxiliary power, the I/O terminal connector provides the interface to:

•Digital output — For connecting external devices such as relays and LEDs. Connected devices can be activated by the VAPIX® Application Programming Interface, output buttons on the Live View page or by an Action Rule. The output will show as active (shown under System Options > Port & Devices > Port Status) if the alarm device is activated.

•Digital input — An alarm input for connecting devices that can toggle between an open and closed circuit, for example: PIRs, door/window contacts, glass break detectors, etc. When a signal is received the state changes and the input becomes active (shown under System Options > Port & Devices > Port Status).

Function

Pin

Notes

Specifications

 

 

 

 

GND

1

Ground

 

 

 

 

 

12 V DC Power

2

Can be used to power auxiliary equipment.

Max load:

 

 

Note: This pin can only be used as power out.

50 mA

 

 

 

 

Configurable (Input

3–4

Digital input — Connect to GND to activate, or leave

0 to +30 V DC

or Output)

 

floating (unconnected) to deactivate.

 

 

 

 

 

 

 

Digital output — Internal connection to ground when

Max load:

 

 

activated, floating (unconnected) when deactivated. If

100 mA

 

 

used with an external relay, a diode must be connected

Max voltage:

 

 

in parallel with the load, for protection against voltage

 

 

+30 V DC

 

 

transients.

 

 

 

 

 

 

 

47

Page 46 Page 48
Image 47
Page 46 Page 48
Contents Axis Q1931-E Thermal Network Camera Intellectual Property Rights About this DocumentLegal Considerations LiabilityLearn More SupportAxis Q1931-E Thermal Network Camera Table of ContentsHardware Overview Connectors and ButtonsNetwork Connector Audio ConnectorControl Button LED IndicatorsPower Connector SD Card SlotStart a browser Internet Explorer, Firefox, Safari Accessing the ProductAccessing the Product Access from a BrowserControls on the Live View Accessing the Product Access from the InternetSet the Root Password Live ViewTo show the manual trigger buttons in the Live View Go to Setup EventsAxis Media Control viewer toolbar Manual TriggerAMC Audio Controls Half-duplex modeAxis Media Control AMC How to Stream H.264Media Streams Media StreamsQuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamJava applet supports simplex audio with G.711 encoding Accessing Audio StreamsBasic Setup Setting Up the ProductSetting Up the Product Pixel Counter Video and AudioVideo and Audio Video Stream264 Click Save to apply the new settingsImage Overlay Camera SettingsExposure Settings Video and Audio Stream ProfilesGo to Events Action Rules Using Overlay Text in an Action RuleOverlay Image Go to Video & Audio Overlay ImageAudio Input Audio SettingsPrivacy Mask Audio ModesAudio Output Audio ClipsAxis Q1931-E Thermal Network Camera Default Viewer for Browsers Live View ConfigLive View Config Output Buttons Viewer SettingsGo to Setup Live View Config User Defined LinksActive/Inactive displays two buttons, one or each action Motion Detection Set Up Motion Detection WindowsDetectors DetectorsMotion Detection Parameters Audio DetectionApplication Licenses Install ApplicationApplications ApplicationsAxis Q1931-E Thermal Network Camera Events EventsGo to Events Action Rules and click Add Setting Up an Action RuleFallback Action Go to Events Recipients and click Add Setting Up an Email RecipientEvents Recipients Recipient Use with actionGo to Events Schedules and click Add SchedulesRecurrences To create a new scheduleContinuous Recording RecordingsRecordings Recording ListLanguages LanguagesUsers System OptionsSystem Options SecurityGo to System Options Security Ieee IeeeCertificates Audio Support Go to Setup System Options Security CertificatesClick Install certificate and upload the certificate Date & TimeSystem Options Network Basic TCP/IP SettingsAxis Video Hosting System Avhs Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service DNS ConfigurationNAT traversal port mapping for IPv4 NTP ConfigurationHost Name Configuration Link-Local IPv4 AddressFTP QoS Quality of ServiceBonjour UPnPTM can be disabled under System Options Network UPnPTMUPnPTM RTP/H.264Go to System Options Storage and click SD Card System Options StorageSD Card Network SharePort Status MaintenancePorts & Devices PortsAdvanced System Options SupportFile Upload Reset to Factory Default SettingsPlain Config Function Pin Specifications Multi-Connector Cable sold separatelyMulti-Connector Cable sold separately Connector Checking the Firmware TroubleshootingTroubleshooting Emergency Recovery ProcedureProduct cannot be accessed from a browser Symptoms, Possible Causes and Remedial ActionsProblems setting the IP address Key frames Product is accessible locally but not externallyProblems with streaming H.264 BasicStorage and disk management problems Video and image problems, generalSetup Video & Audio Camera Settings SettingsTechnical Specifications Technical SpecificationsInstallation Function/group Specifications Audio Audio streamingAlarm triggers Alarm eventsPerformance Considerations Axis Q1931-E Thermal Network Camera M3.4
Top Page Image Contents