Axis Communications Q1931E PT user manual Storage, UPnPTM, RTP/H.264, Bonjour, SD Card

Page 44

AXIS Q1931–E PT Mount Thermal Network Camera

System Options

The following traps are available:

•Cold start

•Warm start

•Link up

•Authentication failed

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see . To enable SNMP v3, check the box and provide the initial user password.

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to Factory Default Settings on page 48.

UPnPTM

The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

UPnPTM can be disabled under System Options > Network > UPnPTM.

RTP/H.264

The RTP port range and multicast settings are configured under System Options > Network > RTP.

The RTP port range defines the range of ports from which the video ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used.

Select Always Multicast Video to start multicast streaming without opening an RTSP session.

Bonjour

The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

Bonjour can be disabled under System Options > Network > Bonjour.

Storage

SD Card

NOTICE

To prevent corruption of recordings, the SD card should always be unmounted before it is ejected.

Supports microSD cards with up to 64 GB of storage. For best recording performance, use a microSDHC or microSDXC card with speed class 10.

The following SD card file systems are supported:

•ext4 — recommended due to its resilience against data loss if the card is ejected or if there is abrupt power loss. To access data stored on the card from the Windows operating system, a third-party ext4 driver or application is required.

•vFAT — supported by most operating systems for personal computers.

The SD card is managed on the System Options > Storage page. Click SD Card to open Storage Management.

44

Image 44

Contents Axis Q1931-E PT Mount Thermal Network Camera About this document Legal ConsiderationsLiability Intellectual Property RightsSupport Learn MoreTable of Contents Axis Q1931-E PT Mount Thermal Network CameraConnectors Performance Considerations Connectors and Buttons Network ConnectorFor technical specifications, see RJ45 Ethernet connector with Power over Ethernet PoELED Indicators Power ConnectorRS485/RS422 Connector SD Card SlotAccess the Product Access from a BrowserAccess from the Internet Set the Root PasswordGo to Setup Events Live ViewControls on the Live View Click Use HttpsAxis Media Control viewer toolbar PTZ ControlsAxis Media Control AMC How to Stream H.264Media Streams Alternative Methods of Accessing the Video Stream QuickTimeTM. The following paths can be usedAxis Q1931-E PT Mount Thermal Network Camera Set Up the Product Basic SetupVideo Video StreamPixel Counter ImageStream Profiles 264Camera Settings Exposure SettingsOverlay Image AppearanceGo to Video Overlay Image Overlay ImageUse Overlay Text in an Action Rule Go to Events Action Rules Under Overlay Settings, select Include textPrivacy Mask Configure the Live View Default Viewer for BrowsersViewer Settings Browser Viewer DescriptionUser Defined Links Preset Positions Go to PTZ Preset PositionsPTZ Pan Tilt Zoom Guard TourInstall PTZ Driver Device SettingsAdvanced Control QueueAxis Q1931-E PT Mount Thermal Network Camera Set Up Motion Detection Windows DetectorsShock Detection Motion DetectionDefault values Parameter Object Size History Sensitivity High level 100%Low level 0% DetectionInstall Application Go to Setup ApplicationsApplications Application LicensesAxis Cross Line Detection Install Axis ApplicationConfigure Axis Cross Line Detection Configure Axis Video Motion Detection Axis Video Motion DetectionAxis Q1931-E PT Mount Thermal Network Camera Setting Up an Action Rule EventsTriggers Go to Events Action Rules and click AddActions Setting Up an Email Recipient Add RecipientsPTZ Control Go to Events Recipients and click AddSchedules RecurrencesTo create a new schedule Go to Events Schedules and click AddRecordings Recording ListContinuous Recording Go to Recordings ListLanguages To log in again and be configured to use this functionality System OptionsSecurity UsersGo to Setup System Options Security Certificates IeeeCertificates Go to System Options Security IeeeBasic TCP/IP Settings Click Install certificate and upload the certificateIPv4 Address Configuration Date & TimeIPv6 Address Configuration Assign IP Address Using ARP/PingARP/Ping Linux/Unix syntaxAdvanced TCP/IP Settings NAT traversal port mapping for IPv4 Select Use the host name to set the host name manuallyLink-Local IPv4 Address QoS Quality of Service Smtp emailStorage UPnPTMRTP/H.264 BonjourNetwork Share Mount and Unmount SD CardFormat SD Card To add a network shareMaintenance Ports & DevicesCOM Port See the online helpSupport Support OverviewSystem Overview Logs & ReportsFile Upload Reset to Factory Default SettingsPlain Config Troubleshooting Upgrade the FirmwareEmergency Recovery Procedure Check the FirmwareSymptoms, Possible Causes and Remedial Actions Problems setting the IP addressProduct cannot be accessed from a browser Product is accessible locally but not externallyProblems with streaming H.264 Video and image problems, generalVideo Camera Settings Storage and disk management problemsVideo cannot be recorded Technical Specifications Function/group Specifications Video ResolutionsImage settings InstallationFunction/group Specifications General Casing PowerConnectors WeightConnectors RS485/422 ConnectorPerformance Considerations M1.10