Axis Communications P3367-VE user manual Storage, UPnPTM, RTP/H.264, Bonjour, SD card

Page 40

AXIS P3367–VE Fixed Dome Network Camera

System Options

The following traps are available:

•Cold start

•Warm start

•Link up

•Authentication failed

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see HTTPS, on page 34. To enable SNMP v3, check the box and provide the initial user password.

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to factory default settings, on page 43.

UPnPTM

The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

UPnPTM can be disabled under System Options > Network > UPnPTM.

RTP/H.264

The RTP port range and multicast settings are conﬁgured under System Options > Network > RTP.

The RTP port range deﬁnes the range of ports from which the video/audio ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used.

Bonjour

The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

Bonjour can be disabled under System Options > Network > Bonjour.

Storage

SD card

The SD/SDHC memory card (not included) is managed on the System Options > Storage page. Click SD card to open Storage Management.

Mounting is done automatically when the card is inserted or when the product boots. SD cards are normally preformatted when purchased, but if needed, click Format to format the card.

Note

To prevent corruption of recordings, the SD card should always be unmounted before removal.

If the card’s status shows as failed, click Check disk to see if the problem can be found and then try Repair.

To avoid ﬁlling the card, it is recommended to remove recordings continuously. Under Recording Settings, select Remove recordings older than and select the number of days or weeks.

To stop writing to the share and protect recordings from being removed, select Lock under Recording Settings.

40

Image 40

Contents Axis P3367-VE Fixed Dome Network Camera About this document LiabilityIntellectual Property Rights Equipment ModiﬁcationsTable of contents Axis P3367-VE Fixed Dome Network CameraHardware overview Hardware overviewConnectors Function Pin SpeciﬁcationsMaintenance LED indicatorsColor Indication Accessing the product Accessing the productAccess from a browser Start a browser Internet Explorer, Firefox, SafariAccess from the Internet Set the root passwordNetwork TCP/IP Advanced Click Create self-signed certiﬁcateConﬁgure capture mode Live ViewControls on the Live View Axis Media Control viewer toolbarAMC Audio controls PTZ ControlsSource list Axis P3367-VE Fixed Dome Network Camera How to stream H.264 Media streamsMedia streams Axis Media Control AMCAlternative methods of accessing the video stream QuickTimeTM. The following paths can be usedAccessing audio streams Java applet supports simplex audio with G.711 encodingSetting up the product Setting up the productBasic Setup Video and Audio Video and AudioVideo Stream Camera Settings Stream ProﬁlesImage 264Capture mode Exposure SettingsImage Appearance White balanceIris adjustment View AreasDay/Night Low light priority slider toward low noiseOverlay Privacy MaskFocus & Zoom Overlay imageWhen satisﬁed, click Enable iris to enable the iris Audio SettingsAudio Channels Audio Input Audio ClipsAudio Output Live View Conﬁg Default viewer for browsersLive View Conﬁg Viewer Settings User Deﬁned LinksOutput Buttons Browser Viewer DescriptionPreset positions Go to PTZ Preset PositionsPTZ Pan Tilt Zoom PTZ Pan Tilt ZoomGuard Tour AdvancedControls To add a guard tourDetectors DetectorsCamera Tampering Motion detectionSet up motion detection Motion detection parametersDefault values Audio detectionLow level 0% Recommended valuesApplications ApplicationsSetting up an Action Rule EventsEvents Status LEDSchedules RecipientsRecurrences Recordings RecordingsRecording List Continuous recordingSystem Options System OptionsSecurity UsersIeee Date & TimeAudio Support Basic TCP/IP Settings NetworkIPv4 Address Conﬁguration IPv6 Address ConﬁgurationAdvanced TCP/IP Settings Link-Local IPv4 Address NAT traversal port mapping for IPv4QoS Quality of Service Smtp emailStorage UPnPTMRTP/H.264 BonjourMaintenance Ports & DevicesNetwork Share PortsIeee 802.1X settings SupportSupport Overview System OverviewReset to factory default settings ScriptingFile Upload Plain ConﬁgAxis P3367-VE Fixed Dome Network Camera Troubleshooting TroubleshootingEmergency recovery procedure Checking the ﬁrmwareProblems setting the IP address Symptoms, possible causes and remedial actionsProduct cannot be accessed from a browser Problems with the H.264 format Product is accessible locally but not externallyStatus and Network indicator LEDs are ﬂashing red rapidly Video and image problems, general Setup Video & Audio Camera SettingsProblems uploading ﬁles No images displayed on webSettings Storage and disk management problemsMotion Detection triggers unexpectedly No audioTechnical Speciﬁcations Technical SpeciﬁcationsAlarm triggers Alarm actionsInstallation aids Software InstallationPerformance considerations Axis P3367-VE Fixed Dome Network Camera M2.2