Axis Communications P3367-VE user manual Connectors, Function Pin Specifications

Page 5

AXIS P3367–VE Fixed Dome Network Camera

Hardware overview

Connectors

Network connector - RJ-45 Ethernet connector. Supports Power over Ethernet (PoE). A shielded network cable (STP) must be used to protect the product against power surges.

Audio in (pink) - 3.5 mm input for a mono microphone, or a line-in mono signal (left channel is used from a stereo signal).

Audio out (green) - 3.5 mm output for audio (line level) that can be connected to a public address (PA) system or an active speaker with a built-in amplifier. A stereo connector must be used for the audio out.

SD card slot - A standard or high-capacity SD card (not included) can be used for local recording with removable storage. For instructions on how to insert and remove an SD card, please refer to the Installation Guide.

Note

Before removal, the SD card should be unmounted to prevent corruption of recordings. To unmount the SD card, go to Setup > System Options > Storage > SD Card and click Unmount.

Control button - The control button is used for:

•Connecting to an AXIS Video Hosting System service. See page 37. To connect, press and hold the button for about 1 second until the Status LED flashes green.

•Connecting to AXIS Internet Dynamic DNS Service. See page 37. To connect, press and hold the button for about 3 seconds.

•Resetting the product to factory default settings. See page 43.

I/O connector

Note

For technical specifications, see page 50.

I/O terminal connector - Use in applications for e.g. motion detection, event triggering, time lapse recording and alarm notifications. In addition to an auxiliary power and a GND pin, the I/O terminal connector provides the interface to:

•Digital output — For connecting external devices such as relays and LEDs. Connected devices can be activated by the VAPIX® Application Programming Interface, output buttons on the Live View page or by an Action Rule. The output will show as active (shown under System Options > Ports & Devices) if the alarm device is activated.

•Digital input — An alarm input for connecting devices that can toggle between an open and closed circuit, for example: PIRs, door/window contacts, glass break detectors, etc. When a signal is received the state changes and the input becomes active (shown under System Options > Ports & Devices).

Function

Pin

Notes

Specifications

 

 

 

 

GND

1

Ground

 

 

 

 

 

3.3 V DC Power

2

Can be used to power auxiliary equipment.

Max load = 50 mA

 

 

Note: This pin can only be used as power out.

 

 

 

 

 

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Axis P3367-VE Fixed Dome Network Camera Liability About this documentIntellectual Property Rights Equipment ModificationsAxis P3367-VE Fixed Dome Network Camera Table of contentsHardware overview Hardware overviewFunction Pin Specifications ConnectorsColor Indication LED indicatorsMaintenance Accessing the product Accessing the productAccess from a browser Start a browser Internet Explorer, Firefox, SafariSet the root password Access from the InternetNetwork TCP/IP Advanced Click Create self-signed certificateLive View Configure capture modeControls on the Live View Axis Media Control viewer toolbarSource list PTZ ControlsAMC Audio controls Axis P3367-VE Fixed Dome Network Camera Media streams How to stream H.264Media streams Axis Media Control AMCQuickTimeTM. The following paths can be used Alternative methods of accessing the video streamJava applet supports simplex audio with G.711 encoding Accessing audio streamsBasic Setup Setting up the productSetting up the product Video Stream Video and AudioVideo and Audio Stream Profiles Camera SettingsImage 264Exposure Settings Capture modeImage Appearance White balanceView Areas Iris adjustmentDay/Night Low light priority slider toward low noisePrivacy Mask OverlayFocus & Zoom Overlay imageAudio Channels Audio SettingsWhen satisfied, click Enable iris to enable the iris Audio Output Audio ClipsAudio Input Live View Config Default viewer for browsersLive View Config User Defined Links Viewer SettingsOutput Buttons Browser Viewer DescriptionGo to PTZ Preset Positions Preset positionsPTZ Pan Tilt Zoom PTZ Pan Tilt ZoomAdvanced Guard TourControls To add a guard tourDetectors DetectorsCamera Tampering Motion detectionMotion detection parameters Set up motion detectionAudio detection Default valuesLow level 0% Recommended valuesApplications ApplicationsEvents Setting up an Action RuleEvents Status LEDRecurrences RecipientsSchedules Recordings RecordingsRecording List Continuous recordingSystem Options System OptionsSecurity UsersAudio Support Date & TimeIeee Network Basic TCP/IP SettingsIPv4 Address Configuration IPv6 Address ConfigurationAdvanced TCP/IP Settings NAT traversal port mapping for IPv4 Link-Local IPv4 AddressSmtp email QoS Quality of ServiceUPnPTM StorageRTP/H.264 BonjourPorts & Devices MaintenanceNetwork Share PortsSupport Ieee 802.1X settingsSupport Overview System OverviewScripting Reset to factory default settingsFile Upload Plain ConfigAxis P3367-VE Fixed Dome Network Camera Troubleshooting TroubleshootingEmergency recovery procedure Checking the firmwareProduct cannot be accessed from a browser Symptoms, possible causes and remedial actionsProblems setting the IP address Status and Network indicator LEDs are flashing red rapidly Product is accessible locally but not externallyProblems with the H.264 format Setup Video & Audio Camera Settings Video and image problems, generalProblems uploading files No images displayed on webStorage and disk management problems SettingsMotion Detection triggers unexpectedly No audioTechnical Specifications Technical SpecificationsAlarm actions Alarm triggersInstallation aids Software InstallationPerformance considerations Axis P3367-VE Fixed Dome Network Camera M2.2
Top Page Image Contents