Changing the Jumper Connector | Kyocera FS-3700 specification

C.2. RS-232C/RS-422A Interface

*Withdrawing the Main Circuit Board from the Printer

Be sure to remove the memory card first if inserted in the printer’s memory card slot.

Withdraw the main circuit board completely from the printer as follows:

1. Turn the printer’s power off. Unplug the printer’s power cable and disconnect the printer from the host computer.

2. Remove the three screws from the printer’s rear cover.

Power OFF (ö)

3. Pull the main circuit board all the way out *of the printer.

Before pulling the main board out, clean an area on the table, etc., at the back of the printer’s rear panel. For- eign objects, accidentally sticking to the back of the main board, can cause serious damage to the printer.

Jumper Connector

Changing the Jumper Connector

1. Carefully remove the jumper connector from the main circuit board, and recon- nect to the pin position shown in the dia- gram.

Jumper Connector

2.After completion of the above, return the main circuit board to the printer by reversing the procedure followed when removing it.

C-7

Image 107

Kyocera FS-3700 manual Withdrawing the Main Circuit Board from the Printer, Changing the Jumper Connector

Contents

FS-1700/3700 Introduction Typeface Trademark Acknowledgement Conforming to the Class a limits CC statement Laser safety Interface connectorsSafety information Important note on the interface connectors Laser notice Ozone concentration Important Safeguards Prolonged Non-Use and Moving the Printer Canadian Department of Communications compliance statementISO Disclaimer FS-3700 Minutes 60 minutes Power consumptionFS-1700 Minutes 30 minutes Introduction Maintenance FeaturesPrint Engine Features Software Features CD-ROM Kyocera Digital Library Installation ManualOptions Guide to the Manual Xii Table of Contents Xiv Fonts Xvi Removing the Main Circuit Board Memory Expansion InstallationPrinting condition Resolution 300 dpi 600 dpi Withdrawing the Main Circuit Board from the Printer Total printer Memory Type and number of SIMMs Simm to be used Removing SIMMs Installing and Removing SIMMsInstalling SIMMs Testing the Expansion Memory Introduction Typeface Trademark Acknowledgement Iii Interface connectors Ozone concentration Important Safeguards Vii Viii Introduction Software Features Options Xii Table of Contents Xiv Fonts Xvi Abandoning a Printing Job On-line/Off-line SettingFeed Selec ion Status Printout Operating Procedures Sample Status Interface-dependent parameters 3a Default font nameFirmware version information Current status information User defined font list Service informationForm Feed Memory allocation status Funct on Default Setting Using the Mode Select MenuMode Select Menu Mode Function Default Setting Please2.4. waitSleep Ecopower Mode KIR Level White vertical stripes Ecoprint modeOptimized stripes Dark vertical strip s SourceResource Protection Adjusting the Print Density Priority Error Mess ge Setting the Audio Warning Buzzer Setting the Audio Warning Buzzer Reading Fonts/Data from a Memory Card Operating a Memory CardHints on Writing Fonts to the Memory Card Memory Writing Da To a Memory Card Deleting Ddata from a Memory Card Formatting destroys any existing data on the memory card Formatting a Memory Card Printing a list of data names Bitmap and Scalable Fonts Fonts Scalable fonts Bitmap fonts Kpdl fonts List of FontsOption Fonts Resident Bitmap Fonts List of Fonts List of Fonts Resident Scalable Fonts List of Fonts List of Fonts Kpdl Fonts Symbol set Symbol set Scalable Fonts Symbol sets Symbol set Maintenance Supplying Toner Close the top cover by pressing the ar Replace the Waste Toner Bottle Do not cap the new waste toner bot- tle Main Charger Unit CleaningCleaning the Charger Wire Cleaning the Grid Paper Feed Unit If the printing is abnormal General GuideIf the printer does not print Interface Problems Power Problems Check the developer unit Print Quality ProblemsCompletely blank printout All-black printout Check the control panel Clean the charger wireDropouts, horizontal streaks, stray dots Black or white vertical streaks Grey background Faint or blurred printing Check the transfer roller Dirt on the top edge or back of the paperCharacters out of position Check the paper chute and the ramp Indicator Condition Correc ive Action Indicators and MessagesIndicators Key Message Corrective Action CallservicepersonFn123456 Error Messages Foccupied Feed cassette Reaching the registration rollers, remove Correcting a Paper Jam Rear Cover Codeset MenuNormal Error due to insufficient FS-1700 FS-3700 Description Printer Specifications Paper Availability General Guidelines Condition of the Paper Paper SpecificationsSpecification Selecting the Right Paper Smoothness Basis WeightMoisture Content Paper Size Other Paper Properties Paper Grain Overhead Projection OHP Film Special Paper Adhesive-Backed Labels Table B.4 lists the specifications for adhesive label paper Recycled Paper EnvelopesColored Paper Preprinted Paper Parallel interface communication modes Parallel Interface Pin In/out Description Interface Signals Detailed descriptions of the signals follow Select In NSelectIn Pin RS-232C interface Interface SignalsPin In/out Signal Description RS-232C/RS-422A Interface Removing*the Main Circuit Board RS-422A interface Changing the Jumper Connector Overview of Signals RS-422A Verifying the Setting RS-422A interface voltage levels Serial Connector Meaning RS-232C/RS-422A ProtocolParameter value Baud rate Parameter value Meaning Prescribe II Frpo D0 commandSerial interface error Error not handled Error handled Preparing an RS-232C Cable Connecting the Printer to the ComputerRS-232C Cable Connection Cmode LPT1=COM1 Last Index Index-2 Index-3