Ecoprint mode, Optimized stripes | Kyocera FS-3700 specs

2.6. Ecoprint mode

Optimized stripes

The current KIR setting s op imal.

Dark vertical strip s

Set the KIR mode to Lightor Medium. Try printing the test pattern again. If you still get dark vertical stripes, adjust the print density control to a lighter setting. (See the last page in this man- ual.)

White vertical stripes

Set the KIR mode to Mediumor Dark. Try printing the test pat- tern again. If you still get white vertical stripes, adjust the print density control to a darker setting. (See the last page in this manual.)

2.6. Ecoprint mode

The Ecoprint enables you to reduce the amount of toner consumed on the page so as to save your printing costs. You can set to Ecoprint mode on, as follows. (The factory-setting is off . )

The Ecoprint mode setting is On when the printing *image becomes lighter, yet very readable.

The Ecoprint setting has no effect on the print speed.

EcoprintOffsetting is	EcoprintOn	setting is
(default).	.

2-16

Image 48

Kyocera FS-3700 manual Ecoprint mode, Optimized stripes, Dark vertical strip s, White vertical stripes

Contents

FS-1700/3700 Introduction Typeface Trademark Acknowledgement CC statement Conforming to the Class a limits Interface connectors Safety informationImportant note on the interface connectors Laser safety Ozone concentration Laser notice Important Safeguards Canadian Department of Communications compliance statement ISODisclaimer Prolonged Non-Use and Moving the Printer Power consumption FS-1700 Minutes 30 minutesFS-3700 Minutes 60 minutes Maintenance Features Print Engine FeaturesIntroduction Software Features Installation Manual OptionsGuide to the Manual CD-ROM Kyocera Digital Library Xii Table of Contents Xiv Fonts Xvi Memory Expansion Installation Printing condition Resolution 300 dpi 600 dpiRemoving the Main Circuit Board Withdrawing the Main Circuit Board from the Printer Simm to be used Total printer Memory Type and number of SIMMs Installing and Removing SIMMs Installing SIMMsRemoving SIMMs Testing the Expansion Memory Introduction Typeface Trademark Acknowledgement Iii Interface connectors Ozone concentration Important Safeguards Vii Viii Introduction Software Features Options Xii Table of Contents Xiv Fonts Xvi On-line/Off-line Setting Feed Selec ionAbandoning a Printing Job Operating Procedures Status Printout Sample Status 3a Default font name Firmware version informationCurrent status information Interface-dependent parameters Service information Form FeedMemory allocation status User defined font list Using the Mode Select Menu Mode Select MenuFunct on Default Setting Function Default Setting Mode Please2.4. waitSleep Ecopower Mode KIR Level Ecoprint mode Optimized stripesDark vertical strip s White vertical stripes Adjusting the Print Density SourceResource Protection Setting the Audio Warning Buzzer Priority Error Mess ge Setting the Audio Warning Buzzer Operating a Memory Card Hints on Writing Fonts to the Memory CardReading Fonts/Data from a Memory Card Writing Da To a Memory Card Memory Deleting Ddata from a Memory Card Formatting a Memory Card Formatting destroys any existing data on the memory card Printing a list of data names Fonts Bitmap and Scalable Fonts Bitmap fonts Scalable fonts List of Fonts Option FontsKpdl fonts Resident Bitmap Fonts List of Fonts List of Fonts Resident Scalable Fonts List of Fonts List of Fonts Kpdl Fonts Symbol set Symbol set Scalable Fonts Symbol sets Symbol set Maintenance Supplying Toner Close the top cover by pressing the ar Replace the Waste Toner Bottle Do not cap the new waste toner bot- tle Cleaning Cleaning the Charger WireMain Charger Unit Cleaning the Grid Paper Feed Unit General Guide If the printer does not printIf the printing is abnormal Power Problems Interface Problems Print Quality Problems Completely blank printoutAll-black printout Check the developer unit Clean the charger wire Dropouts, horizontal streaks, stray dotsBlack or white vertical streaks Check the control panel Faint or blurred printing Grey background Dirt on the top edge or back of the paper Characters out of positionCheck the paper chute and the ramp Check the transfer roller Indicators and Messages IndicatorsIndicator Condition Correc ive Action Message Corrective Action Key Error Messages CallservicepersonFn123456 Foccupied Correcting a Paper Jam Feed cassette Reaching the registration rollers, remove Rear Cover MenuNormal Codeset Error due to insufficient Description FS-1700 FS-3700 Printer Specifications General Guidelines Paper Availability Paper Specifications SpecificationSelecting the Right Paper Condition of the Paper Basis Weight Moisture ContentPaper Size Smoothness Paper Grain Other Paper Properties Special Paper Overhead Projection OHP Film Table B.4 lists the specifications for adhesive label paper Adhesive-Backed Labels Envelopes Colored PaperPreprinted Paper Recycled Paper Parallel Interface Parallel interface communication modes Interface Signals Pin In/out Description Detailed descriptions of the signals follow Select In NSelectIn Pin Interface Signals Pin In/out Signal DescriptionRS-232C/RS-422A Interface RS-232C interface RS-422A interface Removing*the Main Circuit Board Changing the Jumper Connector Verifying the Setting Overview of Signals RS-422A Serial Connector RS-422A interface voltage levels RS-232C/RS-422A Protocol Parameter value Baud rateMeaning Prescribe II Frpo D0 command Serial interface errorError not handled Error handled Parameter value Meaning Connecting the Printer to the Computer RS-232C Cable ConnectionPreparing an RS-232C Cable Cmode LPT1=COM1 Index Last Index-2 Index-3