Replace the Waste Toner Bottle | Kyocera FS-3700 specs

4.1. Toner Kit Replacement

Replace the Waste Toner Bottle

☛When replacing the toner container, the used waste toner bottle in the printer should also be replaced with a new one from the new toner kit.

1. Open the printer side cover.

Side Cover

Old Waste

Toner Bottle

2.Remove the waste toner bottle as shown right.

☛Remove the waste toner bottle as gently as possible so as not to scat- ter the waste toner inside. Do not let the opening of the waste toner bot- tle face downward.

3.Cap the waste toner bottle after remov- ing from the printer.

4.To avoid toner spilling, place the capped waste toner bottle in the plastic bag sup- plied before forwarding to proper dis- posal.

Old Waste

Toner Bottle

Cap

Old Waste

Toner Bottle

Plastic Bag

4-4

Image 73

Kyocera FS-3700 manual Replace the Waste Toner Bottle

Contents

FS-1700/3700 Introduction Typeface Trademark Acknowledgement Conforming to the Class a limits CC statement Safety information Interface connectorsImportant note on the interface connectors Laser safety Laser notice Ozone concentration Important Safeguards ISO Canadian Department of Communications compliance statementDisclaimer Prolonged Non-Use and Moving the Printer FS-1700 Minutes 30 minutes Power consumptionFS-3700 Minutes 60 minutes Print Engine Features Maintenance FeaturesIntroduction Software Features Options Installation ManualGuide to the Manual CD-ROM Kyocera Digital Library Xii Table of Contents Xiv Fonts Xvi Printing condition Resolution 300 dpi 600 dpi Memory Expansion InstallationRemoving the Main Circuit Board Withdrawing the Main Circuit Board from the Printer Total printer Memory Type and number of SIMMs Simm to be used Installing SIMMs Installing and Removing SIMMsRemoving SIMMs Testing the Expansion Memory Introduction Typeface Trademark Acknowledgement Iii Interface connectors Ozone concentration Important Safeguards Vii Viii Introduction Software Features Options Xii Table of Contents Xiv Fonts Xvi Feed Selec ion On-line/Off-line SettingAbandoning a Printing Job Status Printout Operating Procedures Sample Status Firmware version information 3a Default font nameCurrent status information Interface-dependent parameters Form Feed Service informationMemory allocation status User defined font list Mode Select Menu Using the Mode Select MenuFunct on Default Setting Mode Function Default Setting Please2.4. waitSleep Ecopower Mode KIR Level Optimized stripes Ecoprint modeDark vertical strip s White vertical stripes SourceResource Protection Adjusting the Print Density Priority Error Mess ge Setting the Audio Warning Buzzer Setting the Audio Warning Buzzer Hints on Writing Fonts to the Memory Card Operating a Memory CardReading Fonts/Data from a Memory Card Memory Writing Da To a Memory Card Deleting Ddata from a Memory Card Formatting destroys any existing data on the memory card Formatting a Memory Card Printing a list of data names Bitmap and Scalable Fonts Fonts Scalable fonts Bitmap fonts Option Fonts List of FontsKpdl fonts Resident Bitmap Fonts List of Fonts List of Fonts Resident Scalable Fonts List of Fonts List of Fonts Kpdl Fonts Symbol set Symbol set Scalable Fonts Symbol sets Symbol set Maintenance Supplying Toner Close the top cover by pressing the ar Replace the Waste Toner Bottle Do not cap the new waste toner bot- tle Cleaning the Charger Wire CleaningMain Charger Unit Cleaning the Grid Paper Feed Unit If the printer does not print General GuideIf the printing is abnormal Interface Problems Power Problems Completely blank printout Print Quality ProblemsAll-black printout Check the developer unit Dropouts, horizontal streaks, stray dots Clean the charger wireBlack or white vertical streaks Check the control panel Grey background Faint or blurred printing Characters out of position Dirt on the top edge or back of the paperCheck the paper chute and the ramp Check the transfer roller Indicators Indicators and MessagesIndicator Condition Correc ive Action Key Message Corrective Action CallservicepersonFn123456 Error Messages Foccupied Feed cassette Reaching the registration rollers, remove Correcting a Paper Jam Rear Cover Codeset MenuNormal Error due to insufficient FS-1700 FS-3700 Description Printer Specifications Paper Availability General Guidelines Specification Paper SpecificationsSelecting the Right Paper Condition of the Paper Moisture Content Basis WeightPaper Size Smoothness Other Paper Properties Paper Grain Overhead Projection OHP Film Special Paper Adhesive-Backed Labels Table B.4 lists the specifications for adhesive label paper Colored Paper EnvelopesPreprinted Paper Recycled Paper Parallel interface communication modes Parallel Interface Pin In/out Description Interface Signals Detailed descriptions of the signals follow Select In NSelectIn Pin Pin In/out Signal Description Interface SignalsRS-232C/RS-422A Interface RS-232C interface Removing*the Main Circuit Board RS-422A interface Changing the Jumper Connector Overview of Signals RS-422A Verifying the Setting RS-422A interface voltage levels Serial Connector Parameter value Baud rate RS-232C/RS-422A ProtocolMeaning Serial interface error Prescribe II Frpo D0 commandError not handled Error handled Parameter value Meaning RS-232C Cable Connection Connecting the Printer to the ComputerPreparing an RS-232C Cable Cmode LPT1=COM1 Last Index Index-2 Index-3