RS-422A interface | Kyocera FS-3700 instruction

C.2. RS-232C/RS-422A Interface

RS-232C Interface Voltage Levels

The voltage levels of the interface signals conform to EIA RS-232C specifications. SPACE is from 3 volts to 15 volts. MARK is from -3 volts to -15 volts. Voltages between -3 volts and 3 volts are undefined.

RS-422A interface

The serial interface of this printer was set to RS-232C mode before leaving the factory. How- ever, by changing the jumper connector on the main circuit board, the interface can be changed to RS-422A mode.

In RS-232C mode, the printer can be connected to a personal computer (or similar de- vice) equipped with an RS-232C serial interface. (The serial interface is set to RS-232C be- fore leaving the factory.)

In RS-422A mode, the printer can be connected to a personal computer (or similar de-

*vice) equipped with an RS-422A serial interface.

The changing of the main circuit board jumper connector should be carried out only by a Kyocera authorized dealer or Kyocera certified technician. Kyo- cera shall not be liable for damage due to improper changing of this main cir- cuit board jumper connector.

Removing*the Main Circuit Board

The following instructions are intended for the technician only.

Notes on Handling the Main Circuit Board

Protect the electronics by taking these precautions:

Before touching the main circuit board, touch a water pipe or other large metal object to discharge yourself of static electricity. While doing the work, it is recommended

Fthat you wear an antistatic wrist strap.

Touch the main circuit board only by the edge.

C-6

Image 106

Kyocera FS-3700 manual RS-422A interface, Removing*the Main Circuit Board

Contents

FS-1700/3700 Introduction Typeface Trademark Acknowledgement CC statement Conforming to the Class a limits Important note on the interface connectors Interface connectorsSafety information Laser safety Ozone concentration Laser notice Important Safeguards Disclaimer Canadian Department of Communications compliance statementISO Prolonged Non-Use and Moving the Printer FS-1700 Minutes 30 minutes Power consumptionFS-3700 Minutes 60 minutes Print Engine Features Maintenance FeaturesIntroduction Software Features Guide to the Manual Installation ManualOptions CD-ROM Kyocera Digital Library Xii Table of Contents Xiv Fonts Xvi Printing condition Resolution 300 dpi 600 dpi Memory Expansion InstallationRemoving the Main Circuit Board Withdrawing the Main Circuit Board from the Printer Simm to be used Total printer Memory Type and number of SIMMs Installing SIMMs Installing and Removing SIMMsRemoving SIMMs Testing the Expansion Memory Introduction Typeface Trademark Acknowledgement Iii Interface connectors Ozone concentration Important Safeguards Vii Viii Introduction Software Features Options Xii Table of Contents Xiv Fonts Xvi Feed Selec ion On-line/Off-line SettingAbandoning a Printing Job Operating Procedures Status Printout Sample Status Current status information 3a Default font nameFirmware version information Interface-dependent parameters Memory allocation status Service informationForm Feed User defined font list Mode Select Menu Using the Mode Select MenuFunct on Default Setting Function Default Setting Mode Please2.4. waitSleep Ecopower Mode KIR Level Dark vertical strip s Ecoprint modeOptimized stripes White vertical stripes Adjusting the Print Density SourceResource Protection Setting the Audio Warning Buzzer Priority Error Mess ge Setting the Audio Warning Buzzer Hints on Writing Fonts to the Memory Card Operating a Memory CardReading Fonts/Data from a Memory Card Writing Da To a Memory Card Memory Deleting Ddata from a Memory Card Formatting a Memory Card Formatting destroys any existing data on the memory card Printing a list of data names Fonts Bitmap and Scalable Fonts Bitmap fonts Scalable fonts Option Fonts List of FontsKpdl fonts Resident Bitmap Fonts List of Fonts List of Fonts Resident Scalable Fonts List of Fonts List of Fonts Kpdl Fonts Symbol set Symbol set Scalable Fonts Symbol sets Symbol set Maintenance Supplying Toner Close the top cover by pressing the ar Replace the Waste Toner Bottle Do not cap the new waste toner bot- tle Cleaning the Charger Wire CleaningMain Charger Unit Cleaning the Grid Paper Feed Unit If the printer does not print General GuideIf the printing is abnormal Power Problems Interface Problems All-black printout Print Quality ProblemsCompletely blank printout Check the developer unit Black or white vertical streaks Clean the charger wireDropouts, horizontal streaks, stray dots Check the control panel Faint or blurred printing Grey background Check the paper chute and the ramp Dirt on the top edge or back of the paperCharacters out of position Check the transfer roller Indicators Indicators and MessagesIndicator Condition Correc ive Action Message Corrective Action Key Error Messages CallservicepersonFn123456 Foccupied Correcting a Paper Jam Feed cassette Reaching the registration rollers, remove Rear Cover MenuNormal Codeset Error due to insufficient Description FS-1700 FS-3700 Printer Specifications General Guidelines Paper Availability Selecting the Right Paper Paper SpecificationsSpecification Condition of the Paper Paper Size Basis WeightMoisture Content Smoothness Paper Grain Other Paper Properties Special Paper Overhead Projection OHP Film Table B.4 lists the specifications for adhesive label paper Adhesive-Backed Labels Preprinted Paper EnvelopesColored Paper Recycled Paper Parallel Interface Parallel interface communication modes Interface Signals Pin In/out Description Detailed descriptions of the signals follow Select In NSelectIn Pin RS-232C/RS-422A Interface Interface SignalsPin In/out Signal Description RS-232C interface RS-422A interface Removing*the Main Circuit Board Changing the Jumper Connector Verifying the Setting Overview of Signals RS-422A Serial Connector RS-422A interface voltage levels Parameter value Baud rate RS-232C/RS-422A ProtocolMeaning Error not handled Error handled Prescribe II Frpo D0 commandSerial interface error Parameter value Meaning RS-232C Cable Connection Connecting the Printer to the ComputerPreparing an RS-232C Cable Cmode LPT1=COM1 Index Last Index-2 Index-3