Interface connectors, Safety information | Kyocera FS-3700 manual

Introduction

Conforming to the Class B limits

❐DU-20 Duplexer

❐EF-1 Envelope Feeder

❐HS-20 Paper Handler/Stacker

❐IB-3 AppleTalk Interface Board

❐PF-20 Paper Feeder

❐PF-20mini Paper Feeder

❐PK-series KPDL Upgrade Kit

❐SO-6 Sorter/Stacker

❐ST-20 Bulk Paper Stacker

Interface connectors

Important note on the interface connectors

Be sure to turn off printer power before connecting or disconnecting an interface cable to the printer. For protection against static discharge which may be applied to the printer’s internal elec- tronics through the interface connector(s), keep any interface connector which is not in use capped using the protective cap supplied.

☛Use shielded interface cable.

Safety information

Laser safety

This printer is certified as a Class 1 laser product under the U.S. Department of Health and Hu- man Services (DHHS) Radiation Performance Standard according to Radiation Control for Health and Safety Act of 1968. This means that the printer does not produce hazardous laser radiation. Since radiation emitted inside the printer is completely confined within protective housings and external covers, the laser beam cannot escape from the printer during any phase of user operation.

iv

Image 5

Kyocera FS-3700 manual Interface connectors, Safety information, Conforming to the Class B limits, Laser safety

Contents

FS-1700/3700 Introduction Typeface Trademark Acknowledgement Conforming to the Class a limits CC statement Safety information Interface connectorsImportant note on the interface connectors Laser safety Laser notice Ozone concentration Important Safeguards ISO Canadian Department of Communications compliance statementDisclaimer Prolonged Non-Use and Moving the Printer FS-3700 Minutes 60 minutes Power consumptionFS-1700 Minutes 30 minutes Introduction Maintenance FeaturesPrint Engine Features Software Features Options Installation ManualGuide to the Manual CD-ROM Kyocera Digital Library Xii Table of Contents Xiv Fonts Xvi Removing the Main Circuit Board Memory Expansion InstallationPrinting condition Resolution 300 dpi 600 dpi Withdrawing the Main Circuit Board from the Printer Total printer Memory Type and number of SIMMs Simm to be used Removing SIMMs Installing and Removing SIMMsInstalling SIMMs Testing the Expansion Memory Introduction Typeface Trademark Acknowledgement Iii Interface connectors Ozone concentration Important Safeguards Vii Viii Introduction Software Features Options Xii Table of Contents Xiv Fonts Xvi Abandoning a Printing Job On-line/Off-line SettingFeed Selec ion Status Printout Operating Procedures Sample Status Firmware version information 3a Default font nameCurrent status information Interface-dependent parameters Form Feed Service informationMemory allocation status User defined font list Funct on Default Setting Using the Mode Select MenuMode Select Menu Mode Function Default Setting Please2.4. waitSleep Ecopower Mode KIR Level Optimized stripes Ecoprint modeDark vertical strip s White vertical stripes SourceResource Protection Adjusting the Print Density Priority Error Mess ge Setting the Audio Warning Buzzer Setting the Audio Warning Buzzer Reading Fonts/Data from a Memory Card Operating a Memory CardHints on Writing Fonts to the Memory Card Memory Writing Da To a Memory Card Deleting Ddata from a Memory Card Formatting destroys any existing data on the memory card Formatting a Memory Card Printing a list of data names Bitmap and Scalable Fonts Fonts Scalable fonts Bitmap fonts Kpdl fonts List of FontsOption Fonts Resident Bitmap Fonts List of Fonts List of Fonts Resident Scalable Fonts List of Fonts List of Fonts Kpdl Fonts Symbol set Symbol set Scalable Fonts Symbol sets Symbol set Maintenance Supplying Toner Close the top cover by pressing the ar Replace the Waste Toner Bottle Do not cap the new waste toner bot- tle Main Charger Unit CleaningCleaning the Charger Wire Cleaning the Grid Paper Feed Unit If the printing is abnormal General GuideIf the printer does not print Interface Problems Power Problems Completely blank printout Print Quality ProblemsAll-black printout Check the developer unit Dropouts, horizontal streaks, stray dots Clean the charger wireBlack or white vertical streaks Check the control panel Grey background Faint or blurred printing Characters out of position Dirt on the top edge or back of the paperCheck the paper chute and the ramp Check the transfer roller Indicator Condition Correc ive Action Indicators and MessagesIndicators Key Message Corrective Action CallservicepersonFn123456 Error Messages Foccupied Feed cassette Reaching the registration rollers, remove Correcting a Paper Jam Rear Cover Codeset MenuNormal Error due to insufficient FS-1700 FS-3700 Description Printer Specifications Paper Availability General Guidelines Specification Paper SpecificationsSelecting the Right Paper Condition of the Paper Moisture Content Basis WeightPaper Size Smoothness Other Paper Properties Paper Grain Overhead Projection OHP Film Special Paper Adhesive-Backed Labels Table B.4 lists the specifications for adhesive label paper Colored Paper EnvelopesPreprinted Paper Recycled Paper Parallel interface communication modes Parallel Interface Pin In/out Description Interface Signals Detailed descriptions of the signals follow Select In NSelectIn Pin Pin In/out Signal Description Interface SignalsRS-232C/RS-422A Interface RS-232C interface Removing*the Main Circuit Board RS-422A interface Changing the Jumper Connector Overview of Signals RS-422A Verifying the Setting RS-422A interface voltage levels Serial Connector Meaning RS-232C/RS-422A ProtocolParameter value Baud rate Serial interface error Prescribe II Frpo D0 commandError not handled Error handled Parameter value Meaning Preparing an RS-232C Cable Connecting the Printer to the ComputerRS-232C Cable Connection Cmode LPT1=COM1 Last Index Index-2 Index-3