Indicators and Messages | Kyocera FS-3700 guide

5.5. Indicators and Messages

5.5. Indicators and Messages

The tables on the following pages indicate how to respond to problems indicated by the con- trol panel symbolic indicators and messages.

Indicators

Table 5.1 Symbolic Indicators

Indicator

Condition

Correc ive Action

Flashing

The printer has run low on toner. The toner should be replaced as

soon as possible.

Lit

Install a new toner kit. See Section 4.1.

(Toner Empty)

Fast

There is a paper jam. There is possibility that paper may be jammed

at the point indicated by flash ng, open and remove any jammed

Flashing

paper. See Section 5.6.

Slow

The paper has run out in the paper cassette or multi-purpose tray.

Flashing

Please insert paper. See Section 1.4.

Lit

This indicates eith r the current paper feeder or the paper output

point.

The printer has insuffici nt memory available or the printer is

Flashing

warming up (Pleasewait ). Confirm the message indicated

ATTENTION

on the message display. See Section 5.5.

Lit

Note the maintenance message on the message display and consult

Table 5.2.

5-7

Image 84

Kyocera FS-3700 manual Indicators and Messages, Indicator Condition Correc ive Action

Contents

FS-1700/3700 Introduction Typeface Trademark Acknowledgement CC statement Conforming to the Class a limits Interface connectors Safety informationImportant note on the interface connectors Laser safety Ozone concentration Laser notice Important Safeguards Canadian Department of Communications compliance statement ISODisclaimer Prolonged Non-Use and Moving the Printer Power consumption FS-1700 Minutes 30 minutesFS-3700 Minutes 60 minutes Maintenance Features Print Engine FeaturesIntroduction Software Features Installation Manual OptionsGuide to the Manual CD-ROM Kyocera Digital Library Xii Table of Contents Xiv Fonts Xvi Memory Expansion Installation Printing condition Resolution 300 dpi 600 dpiRemoving the Main Circuit Board Withdrawing the Main Circuit Board from the Printer Simm to be used Total printer Memory Type and number of SIMMs Installing and Removing SIMMs Installing SIMMsRemoving SIMMs Testing the Expansion Memory Introduction Typeface Trademark Acknowledgement Iii Interface connectors Ozone concentration Important Safeguards Vii Viii Introduction Software Features Options Xii Table of Contents Xiv Fonts Xvi On-line/Off-line Setting Feed Selec ionAbandoning a Printing Job Operating Procedures Status Printout Sample Status 3a Default font name Firmware version informationCurrent status information Interface-dependent parameters Service information Form FeedMemory allocation status User defined font list Using the Mode Select Menu Mode Select MenuFunct on Default Setting Function Default Setting Mode Please2.4. waitSleep Ecopower Mode KIR Level Ecoprint mode Optimized stripesDark vertical strip s White vertical stripes Adjusting the Print Density SourceResource Protection Setting the Audio Warning Buzzer Priority Error Mess ge Setting the Audio Warning Buzzer Operating a Memory Card Hints on Writing Fonts to the Memory CardReading Fonts/Data from a Memory Card Writing Da To a Memory Card Memory Deleting Ddata from a Memory Card Formatting a Memory Card Formatting destroys any existing data on the memory card Printing a list of data names Fonts Bitmap and Scalable Fonts Bitmap fonts Scalable fonts List of Fonts Option FontsKpdl fonts Resident Bitmap Fonts List of Fonts List of Fonts Resident Scalable Fonts List of Fonts List of Fonts Kpdl Fonts Symbol set Symbol set Scalable Fonts Symbol sets Symbol set Maintenance Supplying Toner Close the top cover by pressing the ar Replace the Waste Toner Bottle Do not cap the new waste toner bot- tle Cleaning Cleaning the Charger WireMain Charger Unit Cleaning the Grid Paper Feed Unit General Guide If the printer does not printIf the printing is abnormal Power Problems Interface Problems Print Quality Problems Completely blank printoutAll-black printout Check the developer unit Clean the charger wire Dropouts, horizontal streaks, stray dotsBlack or white vertical streaks Check the control panel Faint or blurred printing Grey background Dirt on the top edge or back of the paper Characters out of positionCheck the paper chute and the ramp Check the transfer roller Indicators and Messages IndicatorsIndicator Condition Correc ive Action Message Corrective Action Key Error Messages CallservicepersonFn123456 Foccupied Correcting a Paper Jam Feed cassette Reaching the registration rollers, remove Rear Cover MenuNormal Codeset Error due to insufficient Description FS-1700 FS-3700 Printer Specifications General Guidelines Paper Availability Paper Specifications SpecificationSelecting the Right Paper Condition of the Paper Basis Weight Moisture ContentPaper Size Smoothness Paper Grain Other Paper Properties Special Paper Overhead Projection OHP Film Table B.4 lists the specifications for adhesive label paper Adhesive-Backed Labels Envelopes Colored PaperPreprinted Paper Recycled Paper Parallel Interface Parallel interface communication modes Interface Signals Pin In/out Description Detailed descriptions of the signals follow Select In NSelectIn Pin Interface Signals Pin In/out Signal DescriptionRS-232C/RS-422A Interface RS-232C interface RS-422A interface Removing*the Main Circuit Board Changing the Jumper Connector Verifying the Setting Overview of Signals RS-422A Serial Connector RS-422A interface voltage levels RS-232C/RS-422A Protocol Parameter value Baud rateMeaning Prescribe II Frpo D0 command Serial interface errorError not handled Error handled Parameter value Meaning Connecting the Printer to the Computer RS-232C Cable ConnectionPreparing an RS-232C Cable Cmode LPT1=COM1 Index Last Index-2 Index-3