Cleaning the Grid | Kyocera FS-3700 instruction

4.2. Cleaning

Cleaning the Grid

1.Take the grid cleaner from protective bag in the new toner kit, and remove the cap.

☛The grid cleaner pad is impregnated with water. Perform the following cleaning procedure before the pad dries.

2.Attach the grid cleaner to the printer with the pad uppermost, as shown in the dia- gram.

Protective Bag	Cap

Grid Cleaner

Grid Cleaner

3.After attaching the grid cleaner, repeat the action of slowly pulling out and then pushing back in the main charger unit at least 5 times. It is easier to pull out the main charger for the first time if it is raised slightly, as shown in the figure.

The grid part underneath the main charger is cleaned by this procedure.

(1)

(3)

(2)

Main Charger Unit

4.When the grid is clean, remove the grid cleaner from the printer and dispose of it. The grid cleaner is not re-usable.

5.After cleaning the charger wire, push the cleaning knob all the way in and close the side cover.

4-7

Image 76

Kyocera FS-3700 manual Cleaning the Grid

Contents

FS-1700/3700 Introduction Typeface Trademark Acknowledgement CC statement Conforming to the Class a limits Interface connectors Safety informationImportant note on the interface connectors Laser safety Ozone concentration Laser notice Important Safeguards Canadian Department of Communications compliance statement ISODisclaimer Prolonged Non-Use and Moving the Printer FS-1700 Minutes 30 minutes Power consumptionFS-3700 Minutes 60 minutes Print Engine Features Maintenance FeaturesIntroduction Software Features Installation Manual OptionsGuide to the Manual CD-ROM Kyocera Digital Library Xii Table of Contents Xiv Fonts Xvi Printing condition Resolution 300 dpi 600 dpi Memory Expansion InstallationRemoving the Main Circuit Board Withdrawing the Main Circuit Board from the Printer Simm to be used Total printer Memory Type and number of SIMMs Installing SIMMs Installing and Removing SIMMsRemoving SIMMs Testing the Expansion Memory Introduction Typeface Trademark Acknowledgement Iii Interface connectors Ozone concentration Important Safeguards Vii Viii Introduction Software Features Options Xii Table of Contents Xiv Fonts Xvi Feed Selec ion On-line/Off-line SettingAbandoning a Printing Job Operating Procedures Status Printout Sample Status 3a Default font name Firmware version informationCurrent status information Interface-dependent parameters Service information Form FeedMemory allocation status User defined font list Mode Select Menu Using the Mode Select MenuFunct on Default Setting Function Default Setting Mode Please2.4. waitSleep Ecopower Mode KIR Level Ecoprint mode Optimized stripesDark vertical strip s White vertical stripes Adjusting the Print Density SourceResource Protection Setting the Audio Warning Buzzer Priority Error Mess ge Setting the Audio Warning Buzzer Hints on Writing Fonts to the Memory Card Operating a Memory CardReading Fonts/Data from a Memory Card Writing Da To a Memory Card Memory Deleting Ddata from a Memory Card Formatting a Memory Card Formatting destroys any existing data on the memory card Printing a list of data names Fonts Bitmap and Scalable Fonts Bitmap fonts Scalable fonts Option Fonts List of FontsKpdl fonts Resident Bitmap Fonts List of Fonts List of Fonts Resident Scalable Fonts List of Fonts List of Fonts Kpdl Fonts Symbol set Symbol set Scalable Fonts Symbol sets Symbol set Maintenance Supplying Toner Close the top cover by pressing the ar Replace the Waste Toner Bottle Do not cap the new waste toner bot- tle Cleaning the Charger Wire CleaningMain Charger Unit Cleaning the Grid Paper Feed Unit If the printer does not print General GuideIf the printing is abnormal Power Problems Interface Problems Print Quality Problems Completely blank printoutAll-black printout Check the developer unit Clean the charger wire Dropouts, horizontal streaks, stray dotsBlack or white vertical streaks Check the control panel Faint or blurred printing Grey background Dirt on the top edge or back of the paper Characters out of positionCheck the paper chute and the ramp Check the transfer roller Indicators Indicators and MessagesIndicator Condition Correc ive Action Message Corrective Action Key Error Messages CallservicepersonFn123456 Foccupied Correcting a Paper Jam Feed cassette Reaching the registration rollers, remove Rear Cover MenuNormal Codeset Error due to insufficient Description FS-1700 FS-3700 Printer Specifications General Guidelines Paper Availability Paper Specifications SpecificationSelecting the Right Paper Condition of the Paper Basis Weight Moisture ContentPaper Size Smoothness Paper Grain Other Paper Properties Special Paper Overhead Projection OHP Film Table B.4 lists the specifications for adhesive label paper Adhesive-Backed Labels Envelopes Colored PaperPreprinted Paper Recycled Paper Parallel Interface Parallel interface communication modes Interface Signals Pin In/out Description Detailed descriptions of the signals follow Select In NSelectIn Pin Interface Signals Pin In/out Signal DescriptionRS-232C/RS-422A Interface RS-232C interface RS-422A interface Removing*the Main Circuit Board Changing the Jumper Connector Verifying the Setting Overview of Signals RS-422A Serial Connector RS-422A interface voltage levels Parameter value Baud rate RS-232C/RS-422A ProtocolMeaning Prescribe II Frpo D0 command Serial interface errorError not handled Error handled Parameter value Meaning RS-232C Cable Connection Connecting the Printer to the ComputerPreparing an RS-232C Cable Cmode LPT1=COM1 Index Last Index-2 Index-3