Manuals / Kyocera / Computer Equipment / Printer

Kyocera FS-3700 manual RS-422A interface voltage levels, Serial Connector

Models: FS-3700

1 116

Download 116 pages 6.16 Kb

Page 109

C.2. RS-232C/RS-422A Interface

RS-422A interface voltage levels

The interface signal voltage levels conform with the EIA RS-422A standard. The differential voltage varies from 200 mV to 6V.

SERIAL Connector

The connector marked "IöIöI " (RS-232C/RS-422A) on the rear panel is a DB-25S connector. Use a DB-25P connector (or equivalent) for the connector on the cable.

C-9

Image 109

Kyocera FS-3700 manual RS-422A interface voltage levels, Serial Connector

Contents

FS-1700/3700 Introduction Typeface Trademark Acknowledgement Conforming to the Class a limits CC statementSafety information Interface connectorsImportant note on the interface connectors Laser safetyLaser notice Ozone concentrationImportant Safeguards ISO Canadian Department of Communications compliance statementDisclaimer Prolonged Non-Use and Moving the PrinterFS-1700 Minutes 30 minutes Power consumptionFS-3700 Minutes 60 minutes Print Engine Features Maintenance FeaturesIntroduction Software Features Options Installation ManualGuide to the Manual CD-ROM Kyocera Digital LibraryXii Table of Contents Xiv Fonts Xvi Printing condition Resolution 300 dpi 600 dpi Memory Expansion InstallationRemoving the Main Circuit Board Withdrawing the Main Circuit Board from the Printer Total printer Memory Type and number of SIMMs Simm to be usedInstalling SIMMs Installing and Removing SIMMsRemoving SIMMs Testing the Expansion Memory Introduction Typeface Trademark Acknowledgement Iii Interface connectors Ozone concentration Important Safeguards Vii Viii Introduction Software Features Options Xii Table of Contents Xiv Fonts Xvi Feed Selec ion On-line/Off-line SettingAbandoning a Printing Job Status Printout Operating ProceduresSample Status Firmware version information 3a Default font nameCurrent status information Interface-dependent parametersForm Feed Service informationMemory allocation status User defined font listMode Select Menu Using the Mode Select MenuFunct on Default Setting Mode Function Default SettingPlease2.4. waitSleep Ecopower Mode KIR Level Optimized stripes Ecoprint modeDark vertical strip s White vertical stripesSourceResource Protection Adjusting the Print DensityPriority Error Mess ge Setting the Audio Warning BuzzerSetting the Audio Warning Buzzer Hints on Writing Fonts to the Memory Card Operating a Memory CardReading Fonts/Data from a Memory Card Memory Writing Da To a Memory CardDeleting Ddata from a Memory Card Formatting destroys any existing data on the memory card Formatting a Memory CardPrinting a list of data names Bitmap and Scalable Fonts FontsScalable fonts Bitmap fontsOption Fonts List of FontsKpdl fonts Resident Bitmap Fonts List of Fonts List of Fonts Resident Scalable Fonts List of Fonts List of Fonts Kpdl Fonts Symbol set Symbol setScalable Fonts Symbol sets Symbol set Maintenance Supplying Toner Close the top cover by pressing the ar Replace the Waste Toner Bottle Do not cap the new waste toner bot- tle Cleaning the Charger Wire CleaningMain Charger Unit Cleaning the Grid Paper Feed Unit If the printer does not print General GuideIf the printing is abnormal Interface Problems Power ProblemsCompletely blank printout Print Quality ProblemsAll-black printout Check the developer unitDropouts, horizontal streaks, stray dots Clean the charger wireBlack or white vertical streaks Check the control panelGrey background Faint or blurred printingCharacters out of position Dirt on the top edge or back of the paperCheck the paper chute and the ramp Check the transfer rollerIndicators Indicators and MessagesIndicator Condition Correc ive Action Key Message Corrective ActionCallservicepersonFn123456 Error MessagesFoccupied Feed cassette Reaching the registration rollers, remove Correcting a Paper JamRear Cover Codeset MenuNormalError due to insufficient FS-1700 FS-3700 DescriptionPrinter Specifications Paper Availability General GuidelinesSpecification Paper SpecificationsSelecting the Right Paper Condition of the PaperMoisture Content Basis WeightPaper Size SmoothnessOther Paper Properties Paper GrainOverhead Projection OHP Film Special PaperAdhesive-Backed Labels Table B.4 lists the specifications for adhesive label paperColored Paper EnvelopesPreprinted Paper Recycled PaperParallel interface communication modes Parallel InterfacePin In/out Description Interface SignalsDetailed descriptions of the signals follow Select In NSelectIn Pin Pin In/out Signal Description Interface SignalsRS-232C/RS-422A Interface RS-232C interfaceRemoving*the Main Circuit Board RS-422A interfaceChanging the Jumper Connector Overview of Signals RS-422A Verifying the SettingRS-422A interface voltage levels Serial ConnectorParameter value Baud rate RS-232C/RS-422A ProtocolMeaning Serial interface error Prescribe II Frpo D0 commandError not handled Error handled Parameter value MeaningRS-232C Cable Connection Connecting the Printer to the ComputerPreparing an RS-232C Cable Cmode LPT1=COM1 Last IndexIndex-2 Index-3