Manuals / Kyocera / Computer Equipment / Printer

Kyocera FS-3700 manual Setting the Audio Warning Buzzer, Priority Error Mess ge

Models: FS-3700

1 116

Download 116 pages 6.16 Kb

Page 50

2.9.Setting the Audio Warning (Buzzer)

2.9.Setting the Audio Warning (Buzzer)

In addition to the message displayed when the paper supply is exhausted, or when paper jam- ming occurs, an audio warning is made to sound. This is useful, for example, when the printer is in a location some distance from the user.

The audio alarm is set to ON when leaving the factory. An audio alarm corresponding to the

type of printer			rror will s			und according to the table below. If the alarm is set to OFF, it is
made not to sound.
Type of Error			d Corresp			ding Audio Alarm (Buzzer)

							Alarm Frequency
Priority			Error Mess ge				Short beeps: approx. 0.8 s	Remarks
					Tonr		Long beeps: approx. 0.4 s
High		ton		bottlewaster-			short beeps	—
		Replace
		..CleanprintPessCONTr					short beeps	—
		..CleanprintPessCONTr					short beeps	—

		P		jam			short beeps	—

		Fc-downtray					short beeps	—

		Optionfullstcker					short beeps	*

		StackRemoveoverpapOpt.					short beeps	**

		Paperpatherror					short beeps	**

		MemoyPressCONTflow					short beeps	**

		Print				run	short beeps	—

		KPDL		rro			short beeps	—

		MEMORYCARDerr					short beeps	**

		..OptPressCONT.ROMerro					short beeps	**

		PressSepaperCONT					short beeps	**

		Loadpaper					short beeps	—
		Addpaper					short beeps	—
Low							long beeps	—

*Model FS-3700 only

**These error messages are displayed if the relevant option is fitted.

2-18

Image 50

Kyocera FS-3700 manual Setting the Audio Warning Buzzer, Priority Error Mess ge

Contents

FS-1700/3700 Introduction Typeface Trademark Acknowledgement CC statement Conforming to the Class a limitsImportant note on the interface connectors Interface connectorsSafety information Laser safetyOzone concentration Laser noticeImportant Safeguards Disclaimer Canadian Department of Communications compliance statementISO Prolonged Non-Use and Moving the PrinterFS-3700 Minutes 60 minutes Power consumptionFS-1700 Minutes 30 minutes Introduction Maintenance FeaturesPrint Engine Features Software Features Guide to the Manual Installation ManualOptions CD-ROM Kyocera Digital LibraryXii Table of Contents Xiv Fonts Xvi Removing the Main Circuit Board Memory Expansion InstallationPrinting condition Resolution 300 dpi 600 dpi Withdrawing the Main Circuit Board from the Printer Simm to be used Total printer Memory Type and number of SIMMsRemoving SIMMs Installing and Removing SIMMsInstalling SIMMs Testing the Expansion Memory Introduction Typeface Trademark Acknowledgement Iii Interface connectors Ozone concentration Important Safeguards Vii Viii Introduction Software Features Options Xii Table of Contents Xiv Fonts Xvi Abandoning a Printing Job On-line/Off-line SettingFeed Selec ion Operating Procedures Status PrintoutSample Status Current status information 3a Default font nameFirmware version information Interface-dependent parametersMemory allocation status Service informationForm Feed User defined font listFunct on Default Setting Using the Mode Select MenuMode Select Menu Function Default Setting ModePlease2.4. waitSleep Ecopower Mode KIR Level Dark vertical strip s Ecoprint modeOptimized stripes White vertical stripesAdjusting the Print Density SourceResource ProtectionSetting the Audio Warning Buzzer Priority Error Mess geSetting the Audio Warning Buzzer Reading Fonts/Data from a Memory Card Operating a Memory CardHints on Writing Fonts to the Memory Card Writing Da To a Memory Card MemoryDeleting Ddata from a Memory Card Formatting a Memory Card Formatting destroys any existing data on the memory cardPrinting a list of data names Fonts Bitmap and Scalable FontsBitmap fonts Scalable fontsKpdl fonts List of FontsOption Fonts Resident Bitmap Fonts List of Fonts List of Fonts Resident Scalable Fonts List of Fonts List of Fonts Kpdl Fonts Symbol set Symbol setScalable Fonts Symbol sets Symbol set Maintenance Supplying Toner Close the top cover by pressing the ar Replace the Waste Toner Bottle Do not cap the new waste toner bot- tle Main Charger Unit CleaningCleaning the Charger Wire Cleaning the Grid Paper Feed Unit If the printing is abnormal General GuideIf the printer does not print Power Problems Interface ProblemsAll-black printout Print Quality ProblemsCompletely blank printout Check the developer unitBlack or white vertical streaks Clean the charger wireDropouts, horizontal streaks, stray dots Check the control panelFaint or blurred printing Grey backgroundCheck the paper chute and the ramp Dirt on the top edge or back of the paperCharacters out of position Check the transfer rollerIndicator Condition Correc ive Action Indicators and MessagesIndicators Message Corrective Action KeyError Messages CallservicepersonFn123456Foccupied Correcting a Paper Jam Feed cassette Reaching the registration rollers, removeRear Cover MenuNormal CodesetError due to insufficient Description FS-1700 FS-3700Printer Specifications General Guidelines Paper AvailabilitySelecting the Right Paper Paper SpecificationsSpecification Condition of the PaperPaper Size Basis WeightMoisture Content SmoothnessPaper Grain Other Paper PropertiesSpecial Paper Overhead Projection OHP FilmTable B.4 lists the specifications for adhesive label paper Adhesive-Backed LabelsPreprinted Paper EnvelopesColored Paper Recycled PaperParallel Interface Parallel interface communication modesInterface Signals Pin In/out DescriptionDetailed descriptions of the signals follow Select In NSelectIn Pin RS-232C/RS-422A Interface Interface SignalsPin In/out Signal Description RS-232C interfaceRS-422A interface Removing*the Main Circuit BoardChanging the Jumper Connector Verifying the Setting Overview of Signals RS-422ASerial Connector RS-422A interface voltage levelsMeaning RS-232C/RS-422A ProtocolParameter value Baud rate Error not handled Error handled Prescribe II Frpo D0 commandSerial interface error Parameter value MeaningPreparing an RS-232C Cable Connecting the Printer to the ComputerRS-232C Cable Connection Cmode LPT1=COM1 Index LastIndex-2 Index-3