Kyocera FS-3700 guide

1.7. Memory Expansion Installation

*Withdrawing the Main Circuit Board from the Printer

Be sure to remove the memory card first if inserted in the printer’s memory card slot.

Withdraw the main circuit board completely from the printer as follows:

1.Turn the printer’s power off. Unplug the printer’s power cable and disconnect

the printer from the host computer.

2. Remove the three screws from the printer’s rear cover.

Power OFF (ö)

3. Pull the main circuit board all the way out *of the printer.

Before pulling the main board out, clean an area on the table, etc., at the back of the printer’s rear panel. Foreign objects, accidentally sticking to the back of the main board, can cause serious damage to the printer.

Install the SIMM as described on the next

page.

SIMM Sockets

1-24

Image 19

Kyocera FS-3700 manual Withdrawing the Main Circuit Board from the Printer

Contents

FS-1700/3700 Introduction Typeface Trademark Acknowledgement Conforming to the Class a limits CC statement Laser safety Interface connectorsSafety information Important note on the interface connectors Laser notice Ozone concentration Important Safeguards Prolonged Non-Use and Moving the Printer Canadian Department of Communications compliance statementISO Disclaimer FS-1700 Minutes 30 minutes Power consumptionFS-3700 Minutes 60 minutes Print Engine Features Maintenance FeaturesIntroduction Software Features CD-ROM Kyocera Digital Library Installation ManualOptions Guide to the Manual Xii Table of Contents Xiv Fonts Xvi Printing condition Resolution 300 dpi 600 dpi Memory Expansion InstallationRemoving the Main Circuit Board Withdrawing the Main Circuit Board from the Printer Total printer Memory Type and number of SIMMs Simm to be used Installing SIMMs Installing and Removing SIMMsRemoving SIMMs Testing the Expansion Memory Introduction Typeface Trademark Acknowledgement Iii Interface connectors Ozone concentration Important Safeguards Vii Viii Introduction Software Features Options Xii Table of Contents Xiv Fonts Xvi Feed Selec ion On-line/Off-line SettingAbandoning a Printing Job Status Printout Operating Procedures Sample Status Interface-dependent parameters 3a Default font nameFirmware version information Current status information User defined font list Service informationForm Feed Memory allocation status Mode Select Menu Using the Mode Select MenuFunct on Default Setting Mode Function Default Setting Please2.4. waitSleep Ecopower Mode KIR Level White vertical stripes Ecoprint modeOptimized stripes Dark vertical strip s SourceResource Protection Adjusting the Print Density Priority Error Mess ge Setting the Audio Warning Buzzer Setting the Audio Warning Buzzer Hints on Writing Fonts to the Memory Card Operating a Memory CardReading Fonts/Data from a Memory Card Memory Writing Da To a Memory Card Deleting Ddata from a Memory Card Formatting destroys any existing data on the memory card Formatting a Memory Card Printing a list of data names Bitmap and Scalable Fonts Fonts Scalable fonts Bitmap fonts Option Fonts List of FontsKpdl fonts Resident Bitmap Fonts List of Fonts List of Fonts Resident Scalable Fonts List of Fonts List of Fonts Kpdl Fonts Symbol set Symbol set Scalable Fonts Symbol sets Symbol set Maintenance Supplying Toner Close the top cover by pressing the ar Replace the Waste Toner Bottle Do not cap the new waste toner bot- tle Cleaning the Charger Wire CleaningMain Charger Unit Cleaning the Grid Paper Feed Unit If the printer does not print General GuideIf the printing is abnormal Interface Problems Power Problems Check the developer unit Print Quality ProblemsCompletely blank printout All-black printout Check the control panel Clean the charger wireDropouts, horizontal streaks, stray dots Black or white vertical streaks Grey background Faint or blurred printing Check the transfer roller Dirt on the top edge or back of the paperCharacters out of position Check the paper chute and the ramp Indicators Indicators and MessagesIndicator Condition Correc ive Action Key Message Corrective Action CallservicepersonFn123456 Error Messages Foccupied Feed cassette Reaching the registration rollers, remove Correcting a Paper Jam Rear Cover Codeset MenuNormal Error due to insufficient FS-1700 FS-3700 Description Printer Specifications Paper Availability General Guidelines Condition of the Paper Paper SpecificationsSpecification Selecting the Right Paper Smoothness Basis WeightMoisture Content Paper Size Other Paper Properties Paper Grain Overhead Projection OHP Film Special Paper Adhesive-Backed Labels Table B.4 lists the specifications for adhesive label paper Recycled Paper EnvelopesColored Paper Preprinted Paper Parallel interface communication modes Parallel Interface Pin In/out Description Interface Signals Detailed descriptions of the signals follow Select In NSelectIn Pin RS-232C interface Interface SignalsPin In/out Signal Description RS-232C/RS-422A Interface Removing*the Main Circuit Board RS-422A interface Changing the Jumper Connector Overview of Signals RS-422A Verifying the Setting RS-422A interface voltage levels Serial Connector Parameter value Baud rate RS-232C/RS-422A ProtocolMeaning Parameter value Meaning Prescribe II Frpo D0 commandSerial interface error Error not handled Error handled RS-232C Cable Connection Connecting the Printer to the ComputerPreparing an RS-232C Cable Cmode LPT1=COM1 Last Index Index-2 Index-3