Axis Communications P3354 user manual Events

Page 31

AXIS P3354 Network Camera

Events

Events

The Axis product can be configured to perform actions when different events occur, for example, start a recording when motion is detected. The set of conditions that defines how and when the action is triggered is called an Action Rule.

Available action rule triggers and conditions include:

•Applications – Use installed applications to trigger the rule. See Applications, on page 29.

•Detectors

-Day/Night Mode – Trigger the rule when the product switches between day mode (IR cut filter on) and night mode (IR cut filter off). This can for example be used to control an external infrared (IR) light connected to an output port.

-Live Stream Accessed – Trigger the rule when any stream is accessed and during edge storage playback. This can for example be used to send notifications.

-Motion Detection – Trigger the rule when motion is detected. See Motion Detection, on page 26.

-Tampering – Trigger the rule when tampering is detected. See Camera Tampering, on page 26.

•Hardware

-Network – Trigger the rule if network connection is lost or restored. This can for example be used to start recording to the SD card.

-Temperature – Trigger the rule if the temperature falls outside or inside the operating range of the product. This can for example be used to send maintenance notifications.

•Input Signal

-Manual Trigger – Trigger the rule using the Manual Trigger button in the Live View page. See Controls on the Live View Page, on page 9 . This can for example be used to validate actions during product installation and configuration.

-Virtual Inputs – can be used by a VMS (Video Management System) to trigger actions. Virtual inputs can, for example, be connected to buttons in the VMS user interface.

•PTZ

-Error – Trigger the rule if the PTZ functionality is not working correctly. This can for example be used to send maintenance notifications.

-Moving – Trigger the rule when the camera view moves due to a PTZ operation. This can for example be used as an additional condition to prevent an action rule triggered by motion detection to record video while the camera view moves due to a PTZ operation.

-Preset Reached – Trigger the rule when the camera stops at a preset position. This can be for example be used with the Send Images action to upload images from the preset position.

-Ready – Trigger the rule when the PTZ functionality is ready to be used. This can for example be used to steer the camera to a specific preset position when the product is started.

•Storage

-Disruption – Trigger the rule if storage problems are detected, for example if the storage device is unavailable, removed, full, locked or if other read or write problems occur. This can for example be used to send maintenance notifications.

-Recording – Triggers the rule when the Axis product records to the storage device. The recording status trigger can be used to notify the operator, for example by flashing LED lights, if the product has started or stopped to record to the storage device. Note that, this trigger can be used only for edge storage recording status.

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Axis P3354 Network Camera Intellectual Property Rights About this DocumentLegal Considerations LiabilityLearn More SupportAxis P3354 Network Camera Table of ContentsHardware Overview Connectors and ButtonsNetwork Connector For technical specifications, seeSD Card Slot LED IndicatorsColor Indication Start a browser Internet Explorer, Firefox, Safari Accessing the ProductAccessing the Product Access from a BrowserClick Create self-signed certificate Accessing the Product Access from the InternetSet the Root Password Set Power Line FrequencyControls on the Live View Live ViewAxis Media Control viewer toolbar PTZ Controls Axis Media Control AMC How to Stream H.264Media Streams Media StreamsQuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamAxis P3354 Network Camera Setting Up the Product Setting Up the ProductBasic Setup Image Setting Up the Product VideoClick Save to apply the new settings Video StreamStream Profiles Camera Settings264 Wide Dynamic Range Exposure SettingsImage Appearance White BalanceGo to Video View Area Iris adjustmentView Area Day/NightGo to Video Video Stream and select the Image tab Select an Aspect ratio and a Video stream resolutionOverlay Overlay ImageGo to Video Video Stream and select the Image tab When satisfied, click Enable iris to enable the irisPrivacy Mask Focus & ZoomAxis P3354 Network Camera Viewer Settings Live View ConfigLive View Config Default Viewer for BrowsersUser Defined Links Guard Tour Preset PositionsPTZ Pan Tilt Zoom PTZ Pan Tilt ZoomControls Operator Same as administrator but with lower priorityPTZ Pan Tilt Zoom Advanced Control QueueMotion Detection DetectorsDetectors Camera TamperingMotion Detection Parameters Set Up Motion Detection WindowsAxis P3354 Network Camera Application Licenses Install ApplicationApplications ApplicationsAxis P3354 Network Camera Events EventsPTZ Control Setting Up an Action RuleSystem TimeGo to Events Recipients and click Add RecipientsSchedules Recipient Use with actionGo to Events Recurrences and click Add RecurrencesTo create a new schedule Go to Events Schedules and click AddContinuous Recording RecordingsRecordings Recording ListUsers System OptionsSystem Options SecurityCertificates IeeeGo to System Options Security Ieee Network Basic TCP/IP SettingsGo to Setup System Options Security Certificates Date & TimeARP/Ping IPv4 Address ConfigurationIPv6 Address Configuration Axis Internet Dynamic DNS ServiceHost Name Configuration Advanced TCP/IP SettingsDNS Configuration NTP ConfigurationFTP NAT traversal port mapping for IPv4RTP/H.264 QoS Quality of ServiceUPnPTM can be disabled under System Options Network UPnPTM UPnPTMNetwork Share StorageBonjour SD CardTo add a network share MaintenanceGo to System Options Storage Click Network Share Logs & Reports System Options SupportSupport Overview System OverviewPlain Config Reset to Factory Default SettingsFile Upload Checking the Firmware TroubleshootingTroubleshooting Emergency Recovery ProcedureProblems setting the IP address Symptoms, Possible Causes and Remedial ActionsProduct cannot be accessed from a browser Problems with streaming H.264 Product is accessible locally but not externallyBasic Storage and disk management problems Status and Network indicator LEDs are flashing red rapidlyVideo and image problems, general Video Camera SettingsTechnical Specifications Technical SpecificationsMaintenance General Casing Function/group Specifications Network SecurityAlarm actions InstallationPerformance Considerations ConnectorsM3.4

P3354 specifications

Axis Communications P3354 is a high-performance network camera designed to meet the demands of modern security and surveillance applications. Engineered with advanced imaging technologies, this camera offers exceptional video quality, reliability, and versatility for various environments.

One of the key features of the P3354 is its high-resolution video capabilities. With a 2 MP sensor, the camera delivers crisp images at resolutions up to 1080p. This ensures clear and detailed video footage, making it suitable for identifying faces or reading license plates in security-critical applications. The camera supports multiple streaming formats, allowing users to select the appropriate compression and resolution for their specific needs.

The P3354 is built with Axis’ proprietary Wide Dynamic Range (WDR) technology, which enhances image quality in challenging lighting conditions. This is particularly useful in outdoor settings where there can be a significant contrast between light and dark areas. The camera can capture details in both bright highlights and dark shadows, ensuring comprehensive coverage of a scene.

Additionally, the P3354 features Lightfinder technology, which is designed to optimize performance in low-light environments. This innovative technology utilizes a sensitivity-enhancing mechanism that allows the camera to produce color images even in very low light, making it an ideal solution for nighttime security.

The camera's robust design is built to withstand environmental challenges. It comes with an IP66 rating, ensuring that it is dust-tight and can withstand heavy rain, making it suitable for both indoor and outdoor use. The P3354 is also equipped with a tamper-resistant casing to deter vandalism and unauthorized access.

Axis’ application platform enables users to integrate the P3354 with various video management systems and smart analytics features. The camera supports features such as motion detection, audio detection, and tampering alarm, ensuring proactive security monitoring.

Installation and configuration are user-friendly, thanks to the camera's Power over Ethernet (PoE) capability, which simplifies wiring requirements. The P3354 can be easily mounted on walls or ceilings, providing flexible placement options to meet surveillance needs.

In summary, the Axis Communications P3354 is a versatile network camera that combines high-resolution imaging, advanced technologies like WDR and Lightfinder, along with a durable design suited for various environmental conditions. With these features, the P3354 stands as a reliable choice for comprehensive surveillance and security applications.
Top Page Image Contents