Axis Communications P3354 IPv4 Address Configuration, IPv6 Address Configuration, ARP/Ping

Page 39

AXIS P3354 Network Camera

System Options

IPv4 Address Configuration

By default, the Axis product is set to use IPv4 (IP version 4) and to obtain the IP address automatically via DHCP. The IPv4 settings are configured under System Options > Network > TCP/IP > Basic.

DHCP (Dynamic Host Configuration Protocol) allows network administrators to centrally manage and automate the assignment of IP addresses. DHCP should only be enabled if using dynamic IP address notification, or if the DHCP can update a DNS server. It is then possible to access the Axis product by name (host name).

If DHCP is enabled and the product cannot be accessed, run AXIS IP Utility to search the network for connected Axis products, or reset the product to the factory default settings (see page 46) and then perform the installation again.

To use a static IP address, check Use the following IP address and specify the IP address, subnet mask and default router.

IPv6 Address Configuration

If IPv6 (IP version 6) is enabled, the Axis product will receive an IP address according to the configuration in the network router.

To enable IPv6, go to System Options > Network > TCP/IP > Basic. Other settings for IPv6 should be configured in the network router.

ARP/Ping

The product’s IP address can be assigned using ARP and Ping. For instructions, see .

The ARP/Ping service is enabled by default but is automatically disabled two minutes after the product is started, or as soon as an IP address is assigned. To re-assign IP address using ARP/Ping, the product must be restarted to enable ARP/Ping for an additional two minutes.

To disable the service, go to System Options > Network > TCP/IP > Basic and clear the option Enable ARP/Ping setting of IP address.

Pinging the product is still possible when the service is disabled.

AXIS Video Hosting System (AVHS)

AVHS used in conjunction with an AVHS service, provides easy and secure Internet access to live and recorded video accessible from any location. For more information and help to find a local AVHS Service Provider go to www.axis.com/hosting

The AVHS settings are configured under System Options > Network > TCP IP > Basic. The possibility to connect to an AVHS service is enabled by default. To disable, clear the Enable AVHS box.

One-click enabled - Press the product’s control button (see Hardware Overview, on page 5 ) to connect to an AVHS service over the Internet. Once registered, Always will be enabled and the Axis product stays connected to the AVHS service. If the product is not registered within 24 hours from when the button is pressed, the product will disconnect from the AVHS service.

Always - The Axis product will constantly attempt to connect to the AVHS service over the Internet. Once registered the product will stay connected to the service. This option can be used when the product is already installed and it is not convenient to use the one-click installation.

AXIS Internet Dynamic DNS Service

AXIS Internet Dynamic DNS Service assigns a host name for easy access to the product. For more information, see www.axiscam.net

To register the Axis product with AXIS Internet Dynamic DNS Service, go to System Options > Network > TCP/IP > Basic. Under Services, click the AXIS Internet Dynamic DNS Service Settings button (requires access to the Internet). The domain name currently registered at AXIS Internet Dynamic DNS service for the product can at any time be removed.

Note

AXIS Internet Dynamic DNS Service requires IPv4.

39

Page 38 Page 40
Image 39
Page 38 Page 40
Contents
Axis P3354 Network Camera Intellectual Property Rights About this DocumentLegal Considerations LiabilityLearn More SupportAxis P3354 Network Camera Table of ContentsHardware Overview Connectors and ButtonsNetwork Connector For technical specifications, seeLED Indicators SD Card SlotColor Indication Start a browser Internet Explorer, Firefox, Safari Accessing the ProductAccessing the Product Access from a BrowserClick Create self-signed certificate Accessing the Product Access from the InternetSet the Root Password Set Power Line FrequencyLive View Controls on the Live ViewAxis Media Control viewer toolbar PTZ Controls Axis Media Control AMC How to Stream H.264Media Streams Media StreamsQuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamAxis P3354 Network Camera Setting Up the Product Setting Up the ProductBasic Setup Image Setting Up the Product VideoClick Save to apply the new settings Video StreamCamera Settings Stream Profiles264 Wide Dynamic Range Exposure SettingsImage Appearance White BalanceGo to Video View Area Iris adjustmentView Area Day/NightGo to Video Video Stream and select the Image tab Select an Aspect ratio and a Video stream resolutionOverlay Overlay ImageGo to Video Video Stream and select the Image tab When satisfied, click Enable iris to enable the irisPrivacy Mask Focus & ZoomAxis P3354 Network Camera Viewer Settings Live View ConfigLive View Config Default Viewer for BrowsersUser Defined Links Guard Tour Preset PositionsPTZ Pan Tilt Zoom PTZ Pan Tilt ZoomControls Operator Same as administrator but with lower priorityPTZ Pan Tilt Zoom Advanced Control QueueMotion Detection DetectorsDetectors Camera TamperingMotion Detection Parameters Set Up Motion Detection WindowsAxis P3354 Network Camera Application Licenses Install ApplicationApplications ApplicationsAxis P3354 Network Camera Events EventsPTZ Control Setting Up an Action RuleSystem TimeGo to Events Recipients and click Add RecipientsSchedules Recipient Use with actionGo to Events Recurrences and click Add RecurrencesTo create a new schedule Go to Events Schedules and click AddContinuous Recording RecordingsRecordings Recording ListUsers System OptionsSystem Options SecurityIeee CertificatesGo to System Options Security Ieee Network Basic TCP/IP SettingsGo to Setup System Options Security Certificates Date & TimeARP/Ping IPv4 Address ConfigurationIPv6 Address Configuration Axis Internet Dynamic DNS ServiceHost Name Configuration Advanced TCP/IP SettingsDNS Configuration NTP ConfigurationFTP NAT traversal port mapping for IPv4RTP/H.264 QoS Quality of ServiceUPnPTM can be disabled under System Options Network UPnPTM UPnPTMNetwork Share StorageBonjour SD CardMaintenance To add a network shareGo to System Options Storage Click Network Share Logs & Reports System Options SupportSupport Overview System OverviewReset to Factory Default Settings Plain ConfigFile Upload Checking the Firmware TroubleshootingTroubleshooting Emergency Recovery ProcedureSymptoms, Possible Causes and Remedial Actions Problems setting the IP addressProduct cannot be accessed from a browser Product is accessible locally but not externally Problems with streaming H.264Basic Storage and disk management problems Status and Network indicator LEDs are flashing red rapidlyVideo and image problems, general Video Camera SettingsTechnical Specifications Technical SpecificationsMaintenance General Casing Function/group Specifications Network SecurityAlarm actions InstallationPerformance Considerations ConnectorsM3.4
Related manuals
Manual 54 pages 46.9 Kb