Bosch Appliances VG5 700 series Getting Started, Powering On, Establishing AutoDome Control

Page 5

AutoDome 700 Series IP PTZ CameraGetting Started en 5

1

Getting Started

 

 

Install and wire the AutoDome according to the VG5 AutoDome Installation Manual. A typical

 

 

system includes an ethernet connection, a video management system, a monitor, and

 

 

appropriate wiring connections. Please refer to the individual product manuals for complete

 

 

installation and setup instructions for each of the system components.

1.1

Powering On

 

 

 

 

When you turn the AutoDome power on there is a ten (10) second pause before the dome

 

 

starts its homing phase. During the homing phase the camera pans left and right and tilts up

 

 

and down. It also adjusts the lens focus. The entire homing phase lasts approximately 40

 

 

seconds and ends with a firmware version screen.

 

 

 

 

 

 

Bosch Security Sys. AutoDome

 

 

700 Series

5.00.00.03/1.05.00.02

 

 

 

Day/Night 36X

1.00.00.00

 

 

 

SC Boot

5.00.00.03

 

 

 

FPGA

1.13.01.05

 

 

 

Lang. Table

1.00.00.01

 

 

 

VCA_boot

1.02.00.01

 

 

 

IP-Panel

4.53.50.13

 

 

 

IP Address

192.169.0.0

 

 

 

Subnet Mask

255.255.248. 0

 

 

 

No Heater

 

 

FastAddress: Not Set

Figure 1.1 Sample VG5 Startup Firmware Version Screen

The splash screen displays the type of AutoDome, the camera installed, the firmware levels for various files, and the current IP address (for VG5 AutoDome 700 Series models).

1.2

Establishing AutoDome Control

The most common ways to interface with the AutoDome are:

Using the Bosch IP Web interface included with VG5 AutoDome 700 Series models. Refer to Section 2 Using the AutoDome 700 Series, page 6.

Using the Bosch Video Management System (VMS) or the Bosch Video Client.

Using the Bosch Configuration Manager to configure camera settings.

Bosch Security Systems, Inc.

User Manual

F.01U.215.777 1.0 2011.07

Image 5
Contents AutoDome 700 Series IP PTZ Camera Page Table of Contents User Command Table Index Troubleshooting GuideGetting Started Powering OnEstablishing AutoDome Control Seconds and ends with a firmware version screenSystem Requirements Using the AutoDome 700 SeriesOverview of Features Installation manual Connecting the AutoDome 700 Series to the PCUsing the Configuration Manager Configuring the AutoDome 700 Series CameraNetwork Settings Using the AutoDome 700 Series Web ServerMaximum Number of Connections 5The LivepageDisplay Stamping Protected Network Protected AutoDome 700 SeriesImage Selection View ControlSystem Log / Event Log Digital I/OTriggering Relay To Set a Preset Shot To Enter a Keyboard Control CommandTo View a Preset Shot Aux Control TabSaving Snapshots Image ResolutionRecording Video Sequences Processor LoadContact Description Audio Line Input SpecificationsVG5 Audio Connections Activating Audio Reception Enabling Audio Transmission Starting Configuration Configuring the AutoDome 700 SeriesNavigation Making ChangesBasic Mode Date/Time Basic Mode Device AccessBasic Mode Network Page Basic Mode Recording Basic Mode AudioBasic Mode System Overview Advanced Mode GeneralInitiator extension PasswordDate format Date/TimeDevice date/Device time Device time zoneDisplay Stamping Advanced Mode Web Interface Appearance Livepage Functions Encoder Profile Advanced Mode Camera Installer MenuLogging Bosch Security Systems, Inc 01U.215.777 1.0 Expert Settings Video resolutionProfile name Target data rateEncoder Streams Jpeg stream Privacy MasksPreview Camera Settings Night Mode High Sensitivity Setting StabilizationNight Mode Threshold ShutterLens Settings Diagnostics PTZ SettingsTo define a preposition tour Preposition and ToursTo define and edit an individual scene Miscellaneous SectorsLogs AudioAdvanced Mode Recording Storage Management Deactivating Storage Media Formatting Storage MediaRecording Profiles Retention Time Virtual alarmRecording Schedule Recording includesRecording Status Connect on alarm Advanced Mode Alarm Alarm ConnectionsDestination password Number of destination IP addressRemote port Video transmissionVideo output DecoderAlarm status VCA configuration39 VCA VCA ProfilesSensitivity MOTION+ only Motion detector MOTION+ onlyMinimum object size MOTION+ only Select Area MOTION+ onlyTamper detection Trigger delay sSensitivity Global changeAudio Alarm Alarm E-Mail Alarm Rules Alarm Task EditorRelay Advanced Mode Interfaces Alarm InputsAdvanced Mode Network Network Access DNS server address Automatic IP assignmentHttp browser port Https browser portEnable DynDNS Interface mode ETHRCP+ port Telnet supportAdvanced Multicast EnableUPnP TCP Metadata PortFTP Posting Firmware Advanced Mode Service MaintenanceEncryption System Overview LicensesUpload DownloadIf O.K., then If using a non-Bosch power supply Troubleshooting GuideIf O.K., then If there is power to the AutoDome, then VG5 AutoDome Operation and ControlVG5 700 Series AutoDome Video and Control Problem Solution No Network3VG5 Series AutoDome Audio ConnectionProblem Solution No Audio Poor Audio Problem Solution If O.K., thenUser Command Table Index SymbolsJpeg Vidos Page Page Page Page Page Page Bosch Security Systems, Inc