Axis Communications AXIS Q1614 user manual UPnPTM, RTP/H.264

Page 54

AXIS Q1614 Network Camera

System Options

SNMP

The Simple Network Management Protocol (SNMP) allows remote management of network devices. An SNMP community is the group of devices and management station running SNMP. Community names are used to identify groups.

AXIS Video MIB (Management Information Base) for video hardware can be used to monitor Axis-specific, hardware-related issues that may need administrative attention. For more information about AXIS Video MIB and to download MIB files, go to www.axis.com/techsup

To enable and configure SNMP in the Axis product, go to the System Options > Network > SNMP page.

Depending on the level of security required, select the version on SNMP to use.

Traps are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

Note

If HTTPS is enabled, SNMP v1 and SNMP v2c should be disabled.

Traps for SNMP v1/v2 are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

The following traps are available:

•Cold start

•Warm start

•Link up

•Authentication failed

Note

All AXIS Video MIB traps are enabled when SNMP v1/v2c traps are enabled. It is not possible to turn on or off specific traps.

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see HTTPS on page 47. To enable SNMP v3, check the box and provide the initial user password.

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to Factory Default Settings on page 59.

UPnPTM

The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

UPnPTM can be disabled under System Options > Network > UPnPTM.

RTP/H.264

The RTP port range and multicast settings are configured under System Options > Network > RTP.

The RTP port range defines the range of ports from which the video/audio ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used.

Select Always Multicast Video and/or Always Multicast Audio to start multicast streaming without opening an RTSP session.

54

Page 53 Page 55
Image 54
Page 53 Page 55
Contents Axis Q1614 Network Camera Liability About this DocumentLegal Considerations Intellectual Property RightsSupport Learn MoreTable of Contents Axis Q1614 Network CameraTechnical Specifications Storage Ports Maintenance Support AdvancedConnectors Connectors and Buttons For technical specifications, seeHardware Overview Power Connector Network ConnectorConnector Audio ConnectorFunction Button LED IndicatorsStatus LED Behavior for Focus Assistant Color IndicationBuzzer Buzzer Signal for Focus AssistantReplace the Lens LensAxis Q1614 Network Camera Access from the Internet Access the ProductAccess from a Browser Set the Root PasswordSet Power Line Frequency PTZ ModeConfigure Capture Mode Live ViewManual Trigger Go to Setup EventsControls on the Live View To show the manual trigger buttons in the Live ViewAxis Media Control viewer toolbar PTZ ControlsAMC Audio Controls Axis Q1614 Network Camera How to Stream H.264 Media StreamsAxis Media Control AMC Alternative Methods of Accessing the Video Stream QuickTimeTM. The following paths can be usedAccess Audio Streams Java applet supports simplex audio with G.711 encodingSet Up the Product Basic SetupFocus Adjustment Pixel Counter Video and AudioVideo Stream ImageClick Save to apply the new settings Stream Profiles264 Camera Settings Capture ModeGo to Setup Video & Audio Camera Settings Image Appearance Lightfinder ModeExposure Settings White BalanceSet Shutter to Iris configurationIris adjustment Day/NightOverlay To configure the view areaView Area Go to Video & Audio Video Stream and select the Image tabOverlay Image Use Overlay Text in an Action RuleGo to Video & Audio Overlay Image Go to Events Action Rules Privacy MaskFocus BasicAudio Settings Audio ModesAudio Input Audio Clips Audio OutputViewer Settings Configure the Live ViewDefault Viewer for Browsers Browser Viewer DescriptionOutput Buttons Go to Setup Live View ConfigUser Defined Links For more information about I/O ports, see I/O Ports onPTZ Pan Tilt Zoom Preset PositionsGo to PTZ Preset Positions Guard TourAdvanced Install PTZ DriverDevice Settings Control QueueOperator Same as administrator but with lower priority Motion Detection DetectorsCamera Tampering Shock DetectionGo to Detectors Motion Detection Set Up Motion Detection WindowsMotion Detection Parameters Parameter Object Size History Sensitivity DescriptionAudio Detection Applications Install ApplicationGo to Setup Applications Application LicensesAxis Q1614 Network Camera Triggers Set Up Action RulesEvents Go to Events Action Rules and click AddStorage Input SignalHardware SystemActions Set Up Email RecipientsAdd Recipients PTZ ControlTo create a new schedule Set Up RecurrencesCreate Schedules Go to Events Schedules and click AddPlay Recording RecordingsFind Recordings Go to Recordings ListTo play a recording, follow these steps Export Video ClipContinuous Recording Go to Recordings ContinuousLanguages Users System OptionsSecurity IP Address FilterIeee CertificatesGo to System Options Security Ieee Click Install certificate and upload the certificate To install a self-signed certificateGo to Setup System Options Security Certificates Date & TimeBasic TCP/IP Settings NetworkAxis Internet Dynamic DNS Service requires IPv4 Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service DNS ConfigurationLink-Local IPv4 Address NTP ConfigurationHost Name Configuration NAT traversal port mapping for IPv4QoS Quality of Service FTPUPnPTM can be disabled under System Options Network UPnPTM UPnPTMRTP/H.264 SD Card StorageBonjour Mount and Unmount SD CardTo add a network share Under General Settings, select Autoformat toNetwork Share Go to System Options Storage Click Network ShareMaintenance PortsSystem Overview SupportSupport Overview Logs & ReportsReset to Factory Default Settings Plain ConfigFile Upload Emergency Recovery Procedure TroubleshootingUpgrade the Firmware Check the FirmwareProduct cannot be accessed from a browser Symptoms, Possible Causes and Remedial ActionsProblems setting the IP address Product is accessible locally but not externallyVideo and image problems, general Problems with streaming H.264Status and Network indicator LEDs are flashing red rapidly Setup Video & Audio Camera SettingsNo audio SettingsStorage and disk management problems Poor audio qualityTechnical Specifications Audio input Function/group Specifications AudioSpecification Network Security Audio outputConnectors Function/group Specifications Video bufferPower WeightConnector ConnectorsFunction/group Specifications Warranty Function Pin SpecificationsOutput RS485/422 ConnectorPerformance Considerations Function PinAxis Q1614 Network Camera M4.4
Top Page Image Contents