Axis Communications AXIS Q1614 Network Connector, Power Connector, Audio Connector, SD Card Slot

Page 7

AXIS Q1614 Network Camera

Hardware Overview

Network Connector

RJ45 Ethernet connector with Power over Ethernet (PoE).

NOTICE

The product shall be connected using a shielded network cable (STP). All cables connecting the product to the network shall be intended for their specific use. Make sure that the network devices are installed in accordance with the manufacturer’s instructions. For information about regulatory requirements, see Electromagnetic Compatibility (EMC) on page 2 .

I/O Connector

Use with external devices in combination with, for example, tampering alarms, motion detection, event triggering, time lapse recording and alarm notifications. In addition to the 0 V DC reference point and power (DC output), the I/O connector provides the interface to:

•Digital output – For connecting external devices such as relays and LEDs. Connected devices can be activated by the VAPIX® Application Programming Interface, output buttons on the Live View page or by an Action Rule. The output will show as active (shown under System Options > Ports & Devices) if the alarm device is activated.

•Digital input – An alarm input for connecting devices that can toggle between an open and closed circuit, for example: PIRs, door/window contacts, glass break detectors, etc. When a signal is received the state changes and the input becomes active (shown under System Options > Ports & Devices).

Power Connector

2-pin terminal block for power input. Use a Safety Extra Low Voltage (SELV) compliant limited power source (LPS) with either a rated output power limited to ≤100 W or a rated output current limited to ≤5 A.

Audio Connector

The Axis product has the following audio connectors:

•Audio in (pink) – 3.5 mm input for a mono microphone, or a line-in mono signal.

•Audio out (green) – 3.5 mm output for audio (line level) that can be connected to a public address (PA) system or an active speaker with a built-in amplifier . A stereo connector must be used for audio out.

RS485/RS422 Connector

Two terminal blocks for RS485/RS422 serial interface used to control auxiliary equipment such as PTZ devices.

SD Card Slot

A microSD card (not included) can be used for local recording with removable storage. For more information, see Technical Specifications on page 64.

NOTICE

To prevent corruption of recordings, the SD card should be unmounted before removal. To unmount, go to Setup > System Options > Storage > SD Card and click Unmount.

Note

For SD card recommendations see www.axis.com

Control Button

The control button is used for:

•Resetting the product to factory default settings. See page 59.

•Connecting to an AXIS Video Hosting System service. See page 51. To connect, press and hold the button for about 3 seconds until the Status LED flashes green.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Axis Q1614 Network Camera Intellectual Property Rights About this DocumentLegal Considerations LiabilityLearn More SupportAxis Q1614 Network Camera Table of ContentsStorage Ports Maintenance Support Advanced Technical SpecificationsConnectors For technical specifications, see Connectors and ButtonsHardware Overview Audio Connector Network ConnectorConnector Power ConnectorColor Indication LED IndicatorsStatus LED Behavior for Focus Assistant Function ButtonLens Buzzer Signal for Focus AssistantReplace the Lens BuzzerAxis Q1614 Network Camera Set the Root Password Access the ProductAccess from a Browser Access from the InternetLive View PTZ ModeConfigure Capture Mode Set Power Line FrequencyTo show the manual trigger buttons in the Live View Go to Setup EventsControls on the Live View Manual TriggerPTZ Controls Axis Media Control viewer toolbarAMC Audio Controls Axis Q1614 Network Camera Media Streams How to Stream H.264Axis Media Control AMC QuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamJava applet supports simplex audio with G.711 encoding Access Audio StreamsBasic Setup Set Up the ProductFocus Adjustment Image Video and AudioVideo Stream Pixel CounterStream Profiles Click Save to apply the new settings264 Capture Mode Camera SettingsGo to Setup Video & Audio Camera Settings White Balance Lightfinder ModeExposure Settings Image AppearanceDay/Night Iris configurationIris adjustment Set Shutter toGo to Video & Audio Video Stream and select the Image tab To configure the view areaView Area OverlayUse Overlay Text in an Action Rule Overlay ImageGo to Video & Audio Overlay Image Basic Privacy MaskFocus Go to Events Action RulesAudio Modes Audio SettingsAudio Input Audio Output Audio ClipsBrowser Viewer Description Configure the Live ViewDefault Viewer for Browsers Viewer SettingsFor more information about I/O ports, see I/O Ports on Go to Setup Live View ConfigUser Defined Links Output ButtonsGuard Tour Preset PositionsGo to PTZ Preset Positions PTZ Pan Tilt ZoomControl Queue Install PTZ DriverDevice Settings AdvancedOperator Same as administrator but with lower priority Shock Detection DetectorsCamera Tampering Motion DetectionParameter Object Size History Sensitivity Description Set Up Motion Detection WindowsMotion Detection Parameters Go to Detectors Motion DetectionAudio Detection Application Licenses Install ApplicationGo to Setup Applications ApplicationsAxis Q1614 Network Camera Go to Events Action Rules and click Add Set Up Action RulesEvents TriggersSystem Input SignalHardware StoragePTZ Control Set Up Email RecipientsAdd Recipients ActionsGo to Events Schedules and click Add Set Up RecurrencesCreate Schedules To create a new scheduleGo to Recordings List RecordingsFind Recordings Play RecordingGo to Recordings Continuous Export Video ClipContinuous Recording To play a recording, follow these stepsLanguages IP Address Filter System OptionsSecurity UsersCertificates IeeeGo to System Options Security Ieee Date & Time To install a self-signed certificateGo to Setup System Options Security Certificates Click Install certificate and upload the certificateNetwork Basic TCP/IP SettingsDNS Configuration Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service Axis Internet Dynamic DNS Service requires IPv4NAT traversal port mapping for IPv4 NTP ConfigurationHost Name Configuration Link-Local IPv4 AddressFTP QoS Quality of ServiceUPnPTM UPnPTM can be disabled under System Options Network UPnPTMRTP/H.264 Mount and Unmount SD Card StorageBonjour SD CardGo to System Options Storage Click Network Share Under General Settings, select Autoformat toNetwork Share To add a network sharePorts MaintenanceLogs & Reports SupportSupport Overview System OverviewPlain Config Reset to Factory Default SettingsFile Upload Check the Firmware TroubleshootingUpgrade the Firmware Emergency Recovery ProcedureProduct is accessible locally but not externally Symptoms, Possible Causes and Remedial ActionsProblems setting the IP address Product cannot be accessed from a browserSetup Video & Audio Camera Settings Problems with streaming H.264Status and Network indicator LEDs are flashing red rapidly Video and image problems, generalPoor audio quality SettingsStorage and disk management problems No audioTechnical Specifications Audio output Function/group Specifications AudioSpecification Network Security Audio inputWeight Function/group Specifications Video bufferPower ConnectorsFunction Pin Specifications ConnectorsFunction/group Specifications Warranty ConnectorFunction Pin RS485/422 ConnectorPerformance Considerations OutputAxis Q1614 Network Camera M4.4
Top Page Image Contents