Axis Communications axis communications dome network camera Convert Event Types to Action Rules

Page 35

AXIS Q6035 PTZ Dome Network Camera

Events

Available actions include:

•Output Port — activate an I/O port to control an external device.

•Play Audio Clip — see Audio Clips, on page 22.

•PTZ Control

-Autotracking — start autotracking, see Autotracking, on page 26.

-Preset Position — go to a preset position.

-Guard Tour — start a guard tour, see Guard Tour, on page 28.

•Record Video — record video to a selected storage.

•Send Images — send images to a recipient.

•Send Notifications — send a notification message to a recipient.

Convert Event Types to Action Rules

If the Axis product is upgraded to firmware version 5.40 or later, it is recommended to convert Event Types to Action Rules. The legacy user Event Types in the camera will continue to work but will not be visible in the user interface of the camera. The Event Types need to be converted to Action rules to become visible in the user interface.

To convert Event Types to Action Rules go to Events > Action Rules and click Convert.

NOTICE

This is not recommended when using a VMS based on the old Event Management System.

Setting Up an Action Rule

An action rule defines the conditions that must be met for the product to perform an action, for example record video or send email notifications. If multiple conditions are defined, all must be met to trigger the action.

The following example describes how to set up an action rule to record video to a network share if there is movement in the camera’s field of view.

Set up motion detection and add a network share:

1.Go to Detectors > Motion Detection and configure a motion detection window, see page 31

2.Go to System Options > Storage and set up the network share, see page 47.

Set up the action rule:

1.Go to Events > Action Rules and click Add.

2.Select Enable rule and enter a descriptive name for the rule.

3.Select Detectors from the Trigger drop-down list.

4.Select Motion Detection from the drop-down list. Select the motion detection window to use.

5.Optionally, select a Schedule and Additional conditions, see below.

6.Under Actions, select Record Video from the Type drop-down list.

7.Select a Stream profile and configure the Duration settings as described below.

8.Select Network Share from the Storage drop-down list.

35

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Axis Q6035 PTZ Dome Network Camera Intellectual Property Rights SafetyAbout this document LiabilityAxis Q6035 PTZ Dome Network Camera Table of ContentsSymptoms, Possible Causes and Remedial Actions For technical specifications, see ConnectorsHardware Overview Hardware OverviewColor Indication LED IndicatorsMidspan LED Indicators Start a browser Internet Explorer, Firefox, Safari Accessing the ProductAccessing the Product Access from a BrowserNetwork TCP/IP Advanced Access from the InternetSet the Root Password Configure Capture ModeAxis Media Control viewer toolbar Live ViewControls on the Live View AMC Audio Controls PTZ ControlsAxis Q6035 PTZ Dome Network Camera Axis Media Control AMC How to Stream H.264Media Streams Media StreamsQuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamJava applet supports simplex audio with G.711 encoding Accessing Audio StreamsBasic Setup Setting Up the ProductSetting Up the Product Pixel Counter Video and AudioVideo and Audio Video Stream264 Click Save to apply the new settingsStream Profiles ImageImage Appearance Camera SettingsCapture Mode Go to Setup Video & Audio Camera SettingsWide Dynamic Range Exposure SettingsImage Settings OverlayGo to Video & Audio Overlay Image Privacy MaskOverlay Image G711 Audio SettingsAudio Modes Audio InputG726 Audio ClipsAudio Output Live View Config Default Viewer for BrowsersLive View Config Output Buttons Viewer SettingsGo to Setup Live View Config User Defined LinksAxis Q6035 PTZ Dome Network Camera Autotracking Preset PositionsPTZ Pan Tilt Zoom PTZ Pan Tilt ZoomMax Limits ConfigurationExclude Areas Guard Tour GatekeeperLimits Osdi ZonesAdvanced Tour RecordingControls Operator Same as administrator but with lower priorityControl Queue Motion Detection Set Up Motion Detection WindowsDetectors DetectorsMotion Detection Parameters Audio DetectionApplications ApplicationsEvents EventsGo to Events Action Rules and click Add Setting Up an Action RuleConvert Event Types to Action Rules PTZ ControlGo to Events Recipients and click Add RecipientsSchedules Recipient Use with actionGo to Events Recurrences and click Add RecurrencesContinuous Recording RecordingsRecordings Recording ListAxis Q6035 PTZ Dome Network Camera Users System OptionsSystem Options SecurityAudio Support Date & TimeIeee IPv6 Address Configuration Basic TCP/IP SettingsNetwork IPv4 Address ConfigurationAdvanced TCP/IP Settings NAT traversal port mapping for IPv4 Link-Local IPv4 AddressSmtp email QoS Quality of ServiceBonjour StorageUPnPTM RTP/H.264Go to System Options Storage Click Network Share Ports & DevicesNetwork Share PortsSupport MaintenancePlain Config Reset to Factory Default SettingsScripting File Upload192.168.0.90 Checking the Firmware TroubleshootingTroubleshooting Emergency Recovery ProcedureProduct cannot be accessed from a browser Symptoms, Possible Causes and Remedial ActionsProblems setting the IP address Problems with the H.264 format Product is accessible locally but not externallyOverlay image is not displayed Video and image problems, generalSetup Video & Audio Camera Settings No images displayed on webBrowser freezes Problems uploading filesSettings Storage and disk management problemsTechnical Specifications Technical SpecificationsConnectors Installation aidMaintenance PowerMulti-Connector Cable sold separately With the load, for protection against voltage transients Function Pin SpecificationsTo +40 V DC Max voltage = +40 V DCPerformance Considerations Connection diagramDC power input Axis Q6035 PTZ Dome Network Camera M1.8
Top Page Image Contents