Axis Communications axis communications dome network camera Storage, UPnPTM, RTP/H.264, Bonjour

Page 46

AXIS Q6035 PTZ Dome Network Camera

System Options

The following traps are available:

•Cold start

•Warm start

•Link up

•Authentication failed

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see HTTPS, on page 40. To enable SNMP v3, check the box and provide the initial user password.

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to Factory Default Settings, on page 49.

UPnPTM

The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

UPnPTM can be disabled under System Options > Network > UPnPTM.

RTP/H.264

The RTP port range and multicast settings are conﬁgured under System Options > Network > RTP.

The RTP port range deﬁnes the range of ports from which the video/audio ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used.

Select Always Multicast Video and/or Always Multicast Audio to start multicast streaming without opening an RTSP session.

Bonjour

The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

Bonjour can be disabled under System Options > Network > Bonjour.

Storage

SD Card

NOTICE

To prevent corruption of recordings, the SD card should always be unmounted before it is ejected.

The Axis product supports SD cards with the following ﬁle systems:

•ext4 — recommended due to its resilience against data loss if the card is ejected or if there is abrupt power loss. To access data stored on the card from the Windows operating system, a third-party ext4 driver or application is required.

•vFAT — most SD cards are pre-formatted with vFAT when purchased.

If required, the SD card can be re-formatted to the desired ﬁle system. To format the SD card:

1.Insert the SD card in the SD card slot.

2.Go to System Options > Storage and click SD Card.

46

Image 46

Contents Axis Q6035 PTZ Dome Network Camera Liability SafetyAbout this document Intellectual Property RightsTable of Contents Axis Q6035 PTZ Dome Network CameraSymptoms, Possible Causes and Remedial Actions Hardware Overview ConnectorsHardware Overview For technical speciﬁcations, seeMidspan LED Indicators LED IndicatorsColor Indication Access from a Browser Accessing the ProductAccessing the Product Start a browser Internet Explorer, Firefox, SafariConﬁgure Capture Mode Access from the InternetSet the Root Password Network TCP/IP AdvancedControls on the Live View Live ViewAxis Media Control viewer toolbar PTZ Controls AMC Audio ControlsAxis Q6035 PTZ Dome Network Camera Media Streams How to Stream H.264Media Streams Axis Media Control AMCAlternative Methods of Accessing the Video Stream QuickTimeTM. The following paths can be usedAccessing Audio Streams Java applet supports simplex audio with G.711 encodingSetting Up the Product Setting Up the ProductBasic Setup Video Stream Video and AudioVideo and Audio Pixel CounterImage Click Save to apply the new settingsStream Proﬁles 264Go to Setup Video & Audio Camera Settings Camera SettingsCapture Mode Image AppearanceOverlay Exposure SettingsImage Settings Wide Dynamic RangeOverlay Image Privacy MaskGo to Video & Audio Overlay Image Audio Input Audio SettingsAudio Modes G711Audio Output Audio ClipsG726 Live View Conﬁg Default Viewer for BrowsersLive View Conﬁg User Deﬁned Links Viewer SettingsGo to Setup Live View Conﬁg Output ButtonsAxis Q6035 PTZ Dome Network Camera PTZ Pan Tilt Zoom Preset PositionsPTZ Pan Tilt Zoom AutotrackingExclude Areas ConﬁgurationMax Limits Gatekeeper Guard TourTour Recording Osdi ZonesAdvanced LimitsControl Queue Operator Same as administrator but with lower priorityControls Detectors Set Up Motion Detection WindowsDetectors Motion DetectionAudio Detection Motion Detection ParametersApplications ApplicationsEvents EventsPTZ Control Setting Up an Action RuleConvert Event Types to Action Rules Go to Events Action Rules and click AddRecipient Use with action RecipientsSchedules Go to Events Recipients and click AddRecurrences Go to Events Recurrences and click AddRecording List RecordingsRecordings Continuous RecordingAxis Q6035 PTZ Dome Network Camera Security System OptionsSystem Options UsersIeee Date & TimeAudio Support IPv4 Address Conﬁguration Basic TCP/IP SettingsNetwork IPv6 Address ConﬁgurationAdvanced TCP/IP Settings Link-Local IPv4 Address NAT traversal port mapping for IPv4QoS Quality of Service Smtp emailRTP/H.264 StorageUPnPTM BonjourPorts Ports & DevicesNetwork Share Go to System Options Storage Click Network ShareMaintenance SupportFile Upload Reset to Factory Default SettingsScripting Plain Conﬁg192.168.0.90 Emergency Recovery Procedure TroubleshootingTroubleshooting Checking the FirmwareProblems setting the IP address Symptoms, Possible Causes and Remedial ActionsProduct cannot be accessed from a browser Product is accessible locally but not externally Problems with the H.264 formatNo images displayed on web Video and image problems, generalSetup Video & Audio Camera Settings Overlay image is not displayedStorage and disk management problems Problems uploading ﬁlesSettings Browser freezesTechnical Speciﬁcations Technical SpeciﬁcationsPower Installation aidMaintenance ConnectorsMulti-Connector Cable sold separately Max voltage = +40 V DC Function Pin SpeciﬁcationsTo +40 V DC With the load, for protection against voltage transientsDC power input Connection diagramPerformance Considerations Axis Q6035 PTZ Dome Network Camera M1.8